Viewed products





Confianza Online


AEOTEC - Z-Wave+ Nano Dimmer

AEO-ZW111-EU

New

This micromodule light regulator will allow to control a lamp or ceiling light remotely through the Z-Wave protocol while maintaining its existing switch.

More details

In Stock

64,99 €

Technical characteristics

Technology Z-Wave Plus
Characteristic Dimmer

More info

Make your lights smart. With little.


The Nano Dimmer from Aeotec greatly improves the lighting of your home. The third generation of invisible lighting controller from Aeotec surpasses all of the above. The gradation is softer. The compatibility is wider. The lighting is faster and more receptive. Automation and intelligence have never been so powerful. And it comes in such a small size, that you will be surprised at the many features built into it.

Perfect lighting is a part of every truly intelligent home. Lighting that reacts. It is always a good shine. It is always on when you need it and turned off when you do not want it. But perfect lighting has never been easy.

In contrast, perfect lighting was too complicated to achieve. In the past, to automate your lights in Z-Wave you had to worry about the type of wiring you have, if your lighting is up and down and if you are using TRIAC or thyristors. Very complicated. An incorrect configuration and its connected lighting will quickly become a connected headache.

More of that. The Nano Dimmer offers intelligent and connected lighting without any problem.

Easy to install
The Nano Dimmer allows you to add new and existing lights to your Z-Wave system. Makes your lights smarter It makes them sensitive. It gives you the opportunity to control them, vary them and program them.

All this control and intelligence comes from the simple wiring of the Nano Dimmer behind an existing wall switch.

With the AEOTEC Nano Dimmer, switchable and adjustable electrical installations such as lighting or ceiling fans can be integrated into a Z-Wave network. Therefore, the connected load can be switched and attenuated wirelessly via Z-Wave and locally via the existing wall switch. The AEOTEC Nano Dimmer automatically adjusts to the connected lighting and, therefore, can be used with various types of lighting (LED, dimmable LED, CFL, fluorescent, incandescent, halogen). Combined with an appropriate Bypass, it can even dim low-power LEDs and compact fluorescent lamps that use less than 20 watts.

The compact radio module (60% smaller than its predecessor Micro Dimmer) is placed in a wall box just behind the normal switch. The switch is no longer directly connected to the load, but acts as an input device for the AEOTEC insert that controls the load. The switch only sends a control signal to the insert that controls the load again. The solution works with all switch designs. You can use a momentary or lever switch. The use of wall boxes with a depth of 65 mm is recommended. But smaller boxes with a depth of only 45 mm can also be used if there is enough space behind the switch. The space available depends on the size of the traditional switch, the dimensions of the wall box and the amount of additional wiring placed in this box.

characteristics:
Recessed radio module
Integrate existing installations (lighting, ceiling fans) in a Z-Wave network
Works with momentary or lever switches
Voltage: 230 V, 50 Hz
Wiring: compatible with 2 and 3 wire systems (with and without neutral)
Power consumption: <0.8 W
Wireless technology: Z-Wave Plus
Dimensions: 42.5x40x20 mm

Extended Z-Wave info

Name: Nano Dimmer
Manufacturer:Aeotec
Identifier:ZW111-C
Z-Wave Certification Number:ZC10-17015388
Hardware Plattform:ZM5101
FLiRS:NO
Role Type:Always On Slave
Short Description:Aeotec Nano Dimmer is a Z-Wave Smart Dimmer specifically used to enable Z-Wave command and control (on/off/dim) of any wall switches also provides energy metering.
Description:Aeotec Nano Dimmer is a Z-Wave Smart Dimmer specifically used to enable Z-Wave command and control (on/off/dim) of any wall switches. It can report immediate wattage consumption or kWh energy usage over a period of time. In the event of power failure, non-volatile memory retains all programmed information relating to the unit’s operating status. It can connect to 2 external manual switches to control the load ON/OFF independently. Its surface has a pin socket, which can be used for connecting to the touch panel, so you can also use the touch panel to control the Nano Dimmer. The Nano Dimmer is also a security Z-Wave plus device and supports Over The Air (OTA) feature for the products firmware upgrade.

Manual download HERE.

Group
Max Nodes
Description
1
5
Z-Wave Plus Lifeline. When the load state of Nano Dimmer (on/off/dim the load ) is changed, the Hail CC, Switch Multilevel Report and Basic Report (configured by parameter 80) can be sent to the associated nodes in this group.
2
5
Forward the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Switch all to the associated nodes in Group 2 when the Nano Dimmer receives the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Switch all commands from main controller.
3
5
Send Basic Set (configured by parameter 0x51 ) to the associated nodes in Group 3 when the external switch S1 is operated
4
5
Send Basic Set (configured by parameter 0x52) to the associated nodes in Group 4 when the external switch S2 is operated
Number
Size (Bytes)
Default Value
Name
Description
100
1
0
Set parameter 101-103 to default value.
Set parameter 101-103 to default value.
101
4
0
To set which reports need to be sent in Report group 1.
To set which reports need to be sent in Report group 1.
102
1
0
To set which reports need to be sent in Report group 2.
To set which reports need to be sent in Report group 2.
103
1
0
To set which reports need to be sent in Report group 3.
To set which reports need to be sent in Report group 3.
110
1
0
Set parameter 111-113 to default value.
Set parameter 111-113 to default value.
111
4
3
Set the interval of automatic report for Report group 1.
Set the interval of automatic report for Report group 1.
112
4
600
Set the interval of automatic report for Report group 2.
Set the interval of automatic report for Report group 2.
113
4
600
Set the interval of automatic report for Report group 2.
Set the interval of automatic report for Report group 3.
120
1
0
Configure the external switch mode for S1.
Configure the external switch mode for S1.
121
1
0
Configure the external switch mode for S2.
Configure the external switch mode for S2.
122
1
0
Get the state of touch panel port
Get the state of touch panel port
123
1
3
Set the control destination for external switch S1
Set the control destination for external switch S1
124
1
3
Set the control destination for external switch S2
Set the control destination for external switch S2.
125
1
3
Set the default dimming rate.
Set the default dimming rate.
128
1
0
Get the current working mode
Get the current working mode. Note: This parameter is a Get-only parameter.
129
1
1
Set the dimming principle
Set the dimming principle.
130
1
0
To get what type of load the Dimmer is connected to.
To get what type of load the Dimmer is connected to. Note: This parameter is a Get-only parameter.
131
1
0
Set the min brightness level that the load can reach to.
Set the min brightness level that the load can reach to.
132
1
99
Set the max brightness level that the load can reach to. Note:
Set the max brightness level that the load can reach to. Note:
20
1
0
Configure the output status after re-power on it.
Configure the output status after re-power on it.
249
1
2
Set the recognition way of load
Set the recognition way of load
252
1
0
Lock/unlock configuration parameters
Lock/unlock configuration parameters.
255
4
0
Reset the Nano Dimmer
Reset the Nano Dimmer to factory default.
3
1
1
Current Overload Protection.
Output Load will be turned off automatically after 30 seconds and if the current overrun 1.5A.
4
1
0
Overheat protection.
Output Load will be turned off automatically after 30 seconds and if the temperature of product inside exceeds 100 ℃.
80
1
0
To set which notification would be sent to the associated devices (Group 1)
To set which notification would be sent to the associated devices (Group 1) when the state of Nano Dimmer’s load is changed.
81
1
1
To set which notification would be sent to the associated nodes in association group 3
To set which notification would be sent to the associated nodes in association Group 3 when using the external switch 1 to switch the loads.
82
1
1
To set which notification would be sent to the associated nodes in association group 4
To set which notification would be sent to the associated nodes in association Group 4 when using the external switch 2 to switch the loads.
85
4
1573017
Set appointment 1
Set the ON time of output load.
86
4
2293760
Set appointment 2
Set the ON time of output load.
90
1
0
Enables/disables parameter 91 and 92 below:
Enables/disables the function of parameter 91 and 92.
91
2
25
Set the threshold value of wattage.
Threshold change in wattage (in terms of wattage) to induce an automatic report.
92
1
5
Set the threshold value of wattage.
Threshold change in wattage (in terms of percentage) to induce an automatic report.
Basic
COMMAND_CLASS_BASIC
Hail
COMMAND_CLASS_HAIL
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Clock
COMMAND_CLASS_CLOCK
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V3
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V3
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V3
COMMAND_CLASS_METER_V3
Notification V4
COMMAND_CLASS_NOTIFICATION_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Scene Activation
COMMAND_CLASS_SCENE_ACTIVATION
Scene Actuator Conf
COMMAND_CLASS_SCENE_ACTUATOR_CONF
Security S0
COMMAND_CLASS_SECURITY
Switch All
COMMAND_CLASS_SWITCH_ALL
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Switch Multilevel V3
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Inclusion
Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Action button that you can find on the product's housing.
Exclusion
Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Action button that you can find on the product's housing.
Factory Reset
Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is missing or inoperable.
Additional Special Features
Support ""Over the Air Firmware Updating"" and “Z-Wave Security”.

Electric Load Type
Select the electric load type(s) supported by the device.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Neutral Wire Required
For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.
Supported Meter Type
Indicate which type of metering is supported by the device.
Switch Type
Describes the type of operator for a switch.
Z-Wave Scene Type
Indicates which of the two types of Z-Wave scene command classes are supported. Scenes or Central Scene

 

Reviews

Write a review

AEOTEC - Z-Wave+ Nano Dimmer

AEOTEC - Z-Wave+ Nano Dimmer

This micromodule light regulator will allow to control a lamp or ceiling light remotely through the Z-Wave protocol while maintaining its existing switch.

30 other products in the same category:

Customers who bought this product also bought: