Viewed products





Confianza Online


Aeotec Nano Shutter Micromodule Blinds Z-Wave Plus

AEO_ZW141-EU

New

The control for blinds Z-Wave Aeotec Nano Shutter makes the motor controls of your blind, awning, blind or curtain, etc. are connected to your Z-Wave wireless network.

More details

Out of stock

49,99 €

Technical characteristics

Technology Z-Wave Plus

More info

Nano Shutter. The controls of the motor of its shutter are connected in Z-Wave.
Security shutters for skylights, electronic devices and motorized furniture are part of a modern home. Now, they can be part of your connected home.

The Nano Shutter integrates with the engines and converts them into Z-Wave. Instantly, everything connected can be wirelessly controlled and intelligently automated thanks to the Nano Shutter that can be integrated with a wide selection of devices.

Easy to install Simple to control.
The Nano Shutter is connected to the accessories of your home controlled by an engine. It simply does this and immediately makes these accessories available for control, automation and planning through Z-Wave.

It can be connected to connect directly to the motor. It can be connected to any existing wall switch that controls the motor. And you can connect in seconds to WallSwipe, which allows you to further improve the Nano Shutter for tactile and gestural control.

Once installed, you can control the Nano Shutter through any connected switch and through Z-Wave through its gateway, its remote control and the application of your smartphone.

Made with experience
The Nano Shutter is designed from the same 10-year experience that has been infused into the Nano Dimmer and the Nano Switch. The experience that includes the engineering of the first Z-Wave shutter controller; the motor micro driver.

With this experience, the Nano Shutter offers 3 new essential improvements for this technology.

Better security
For any engine that controls access points, such as security doors and shutters, the Z-Wave S2 is crucial. The S2 improves the Nano Shutter with state-of-the-art anti-piracy features, including 128-bit AES encryption and ECDH key exchange.

Z-Wave Plus.
In addition to its advanced security, the Z-Wave Plus Nano Shutter. The latest version of Z-Wave allows the Nano Shutter to control connected accessories with a response time of 250% faster and a wireless range of 67% higher, up to 150 meters.

60% smaller.
Designed to be easy to install, the Nano shutter has also been designed to be easier to install. With only 43 x 20 cm, it is 60% smaller than the Micro Motor Controller, which means that it is even easier to install behind the motor switches.

Attention, this module requires the neutral to work.

FUNCTIONS:

Order your blinds or blinds remotely
Installs behind an existing switch
Function up / down (without positioning)
Integrates the Z-Wave 500 series chip.
Communication 250% faster compared to standard Z-Wave devices
Supports the Z-Wave S2 security framework
Automatic detection of the type of switch.
Compatible with all Z-Wave and Z-Wave + controllers
Measurement of the instantaneous and cumulative consumption function.
Connector for WallSwipe switch (coming soon)
Use with toggle or impulse switch
Small, discreet and aesthetic.
Ease of use and installation.


TECHNICAL CHARACTERISTICS :

Module type: Z-Wave receiver
Power supply: 120-240VAC, 50 / 60Hz
Standby power consumption: <0.8W
Wiring: 3 wires, neutral required
Maximum load: 2.5A
Status indicator: LED
Frequency: 868.42 Mhz
Transmission distance: 150m in free field.
Dimensions: 42.5mm x 40mm x 20mm
Operating temperature: 0-40 ° C
Operating humidity: 8-80%
Certifications: FCC, UL, CE, ROHS

Extended Z-Wave info

Name: Nano Shutter
Manufacturer:Aeotec
Identifier:ZW141-C
Z-Wave Certification Number:ZC10-19126810
Hardware Plattform:ZM5101
FLiRS:NO
Role Type:Always On Slave
Short Description:Aeotec New Generation motor controller
Description:Aeotec New Generation Nano Shutter 1. Used to control the motor of Curtain, support Shutter Mode and Venetian Mode . 2. Can be calibrated according to diff e rent curtains 3. Used to control other Z-Wave device directly. 4. Support S2, more safe and more re liable 5. Support SmartStart, faster inclusion

Manual download HERE.

Group
Max Nodes
Description
1
5
Used for some commands auto sending when status changed.
2
5
Retransmit when receiving the follow commands
Number
Size (Bytes)
Default Value
Name
Description
120
1
0
Switch Type of External Switch 1
Used to set Switch type of External Switch 1,and reports will return automatically during identify.
121
1
0
Switch Type of External Switch 1
Used to set Switch type of External Switch 1,and reports will return automatically during identify.
20
1
0
Motor Behavior After Power ON
Setting the Motor Behavior After Power ON.
22
1
0
Determine motor run direction
Note: 1.Motor will stop when receiving this command in moving; 2.This configuration will not change after network exclusion or Configuration Reset.
248
1
1
Function Setting of External Switch S1&S2
Used to Enable/Disable function of External Switch S1&S2. Note : This value can be combine, e.g. set to 3(1+2=3),means networking function and Reset function are both enable.
255
4
0
Reset Function
Used to reset configuration parameter value to default value or reset to factory default settings. Note: Parameter 0x16, 0x22, 0x23, 0x24, 0x25, 0x27, 0x28 will not reset to default value by this command.
34
2
150
Set the Blade Turn Time
This parameter is to config the blade turn time(unit = 0.01s),which works only for venetian mode.Details can be found in section 4.2 of Advanced information Product Manual. Note: For Venetian, if this value is set too large for blade turning, curtain may move upwards or downwards. Calibration need to work correctly.Or this setting will force the curtain to move up or down. This configuration will not change after network exclusion or Configuration Reset.
35
2
15000
Curtain Trip Time
Curtain Trip Time is about the run time of the curtain (unit = 0.01s). Details can be found in section 4.2 of Advanced information Product Manual. Note: For Venetian, if this value is set too large for blade turning, curtain may move upwards or downwards. Calibration need to work correctly.Or this setting will force the curtain to move up or down. This configuration will not change after network exclusion or Configuration Reset.
36
1
0
Enter/Exit Calibration
Note: Product will enter the right Curtain Mode after calibration, see Configuration 0x27(39)
37
1
0
User confirmation for Calibration
User confirmation for Calibration(set only)
38
1
0
Calibration Status Report
Return Calibration Status(Get or Report)
39
1
0
Cutain Mode Setting
Set the Curtain Mode. Note: 1. This Operation will enter repositioning automatically; 2. This configuration will not change after network exclusion or Configuration Reset.
40
1
1
Repositioning
Set to begin repositioning.
41
1
0
Repositioning Status Report
Used to Get repositioning Status.
42
1
1
Calibration Lock
Used to enable/disable calibration lock from different ways.
80
1
2
Switch Status Report Selection
Choose which report to send when switch status change
85
1
0
Extern Button Mode Setting
Extern Button Mode Setting Note: when setting value to 2, we advice not to set only one external switch to push button, do remember to change the controller channel before operating push button, or the curtain level will be wrong.
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic V2
COMMAND_CLASS_BASIC_V2
Central Scene V3
COMMAND_CLASS_CENTRAL_SCENE_V3
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V4
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Powerlevel
COMMAND_CLASS_POWERLEVEL
Scene Activation
COMMAND_CLASS_SCENE_ACTIVATION
Scene Actuator Conf
COMMAND_CLASS_SCENE_ACTUATOR_CONF
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Supervision
COMMAND_CLASS_SUPERVISION
Switch Multilevel V4
COMMAND_CLASS_SWITCH_MULTILEVEL_V4
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Classic Exclusion
3.6 How to Remove the device from Z-Wave network

1. Set your Z-Wave Controller into its 'Remove Device' mode in order to remove the product from your Z-Wave system. Refer to the Controller's manual if you are unsure of how to perform this step.

2. Click Action Button/S1/S2(external switch need to be identified first) 6 times will enter exclusion mode.

3. If Removing fails, it will bright red light for 2s then turn back to Regular Light Mode, repeat steps 1-2. Contact us for further support if needed.

4. If Removing succeeds, it will alternate through a rainbow of colors. Now, it is removed from Z-Wave network successfully.

Other Special Features
Calibration for Shutter have 2 modes: Shutter Mode for Standard roller blind, and Venetian Mode for Venetian Blind. Shutter will record the Curtain Trip Time for Shutter mode and Curtain Trip Time + Blade Turn Time for Venetain Mode.



The detail can be found in section 4.2 Calibration in Advanced information Product Manual.
Where to find S2 DSK on product
There is no DSK on the product.QR code used for SmartStart inclusion. DSK code can be found on packaging.
Factory Reset Procedure
3.7 How to Factory Reset

Manually, press and hold the Action Button for at least 20s and then release. The LED indicator will alternate through a rainbow of colors, which indicates the reset operation is successful. Otherwise, please try again. Contact us for further support if needed.

Note:

1. This procedure should only be used when the primary controller is missing or inoperable.

2. Factory Reset will:

a) Remove the product from Z-Wave network;

b) Delete the Association setting;

Classic Inclusion
3.5.2 Classic inclusion Learn Mode

1. Set your Z-Wave Controller into its 'Add Device' mode in order to add the product into your Z-Wave system. Refer to the Controller's manual if you are unsure of how to perform this step.

2. Make sure the product is powered. After powered up, Its LED will alternate through a rainbow of colors all the time.

3. Click Action Button once, it will quickly flash blue light for 30 seconds until it is added into the network.

4. If your Z-Wave Controller supports S2 encryption, enter the first 5 digits of DSK into your Controller's interface if /when requested. The DSK is printed on its housing.

5. If Adding fails, it will bright red light for 2s and then alternate through a rainbow of colors; repeat steps 1 to 4. Contact us for further support if needed.

6. If Adding succeeds, it will bright blue light for 2s and then turn to Motor Mode(green for runing, off for stop). Now, this product is a part of your Z-Wave home control system. You can configure it and its automations via your Z-Wave system; please refer to your software's user guide for precise instructions.

S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Color
If the product is only available in one color, pick the color from the list.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Neutral Wire Required
For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps
Window Covering Control Features
Select the feature(s) supported in the Window Covering Control product.

 

Reviews

Write a review

Aeotec Nano Shutter Micromodule Blinds Z-Wave Plus

Aeotec Nano Shutter Micromodule Blinds Z-Wave Plus

The control for blinds Z-Wave Aeotec Nano Shutter makes the motor controls of your blind, awning, blind or curtain, etc. are connected to your Z-Wave wireless network.

30 other products in the same category:

Customers who bought this product also bought: