Viewed products





Confianza Online


FIBARO Door / Window Sensor 2 Opening and temperature detector for door / window Z-Wave Plus

New

Z-Wave + opening detector available in various colors for doors, windows, roof windows, etc. ElFIBARO Door / Window Sensor 2 for door / window combines the functionality of two devices: a contact and temperature sensor in a single product Easy to use. It also has a double protection against sabotage.

More details

In Stock

49,99 €

Technical characteristics

Technology Z-Wave Plus

More info

It is a magnetic sensor Z-Wave + called with temperature sensor that will allow you to control the open or closed state of doors and windows. Integrable with other Z-Wave devices such as motion sensors , flood sensors , alarm sensors , etc., allows you to create different events, if you have a Z-Wave controller .

It has a mobile part with a magnet fixed on the door or window, and the main unit located in the fixed part of the window or door. When both parties are not facing each other, a Z-Wave radio signal is automatically sent. Very easy to install, the main unit is usually placed in the moving part of the window or door, and the magnetic element is installed in the frame. Available in various colors (white, black, gray, light gray, brown, light brown, dark brown) so as not to clash with the color of your doors and windows.

This 4-function battery operated detector for Z-Wave wireless networks has a magnetic proximity sensor to detect the opening of a door or window. The device consists of a part with magnets (the mobile part) fixed in the door or window, and the main unit located in the fixed part of the window or door with screws or by means of adhesive. When both parties are not facing each other, a signal is automatically sent to the Z-Wave radio network.

In addition, the sensor has a temperature sensor.

A Z-Wave Control Unit is required to integrate this sensor into the Z-Wave network.

CHARACTERISTICS:

  • Opening detector
  • Temperature sensor
  • Button to include / exclude the detector
  • Low battery detection
  • Protection handling
  • Very small size
  • Ease of use and installation

SPECIFICATIONS :

  • Module type: wireless behavior as a Z-Wave transmitter
  • Wireless behavior: slave
  • Colors: White, Gray, Black, Light Gray, Light Brown, Brown, Dark Brown
  • Power: ER14250 battery (1 / 2AA) 3.6 V
  • Frequency: 868.42 Mhz
  • Transmission distance: 50m free field, 30m in buildings
  • Dimensions: 76 x 17 x 19 mm
  • Operating temperature: 0-40 ° C
  • Certifications:
    • RoHS 2011/65 / EU
    • LVD 2006/95 / WE
    • EMC 2004/108 / WE
    • R & TTE 1999/5 / WE

Z-Wave Plus - Fibaro ZW5Meets CE and ROHS Certifications

Extended Z-Wave info

Name: FIBARO Door/Window Sensor 2
Manufacturer:FIBARO
Identifier:FGDW-002
Z-Wave Certification Number:ZC10-17035459
Hardware Plattform:ZM5101
FLiRS:NO
Role Type:Reporting Sleeping Slave
Short Description:FIBARO Door/Window Sensor 2 is a wireless, battery powered, Z-Wave Plus compatible magnetic contact sensor.
Description:FIBARO Door/Window Sensor 2 is a wireless, battery powered, Z-Wave Plus compatible magnetic contact sensor. Changing the device’s status will automatically send signal to the Z-Wave controller and associated devices. In addition the FIBARO Door/Window Sensor 2 is equipped with a built-in temperature sensor. Sensor can be used to trigger scenes and wherever there is a need for information about opening or closing of doors, windows, garage doors, etc. Opening is detected by separating the sensor’s body and the magnet.

Manual download HERE.

Group
Max Nodes
Description
1
1
“Lifeline” reports the device status and allows for assigning single device only (main controller by default).
2
5
2nd Association Group – “On/Off” is assigned to the device status - Hall effect sensor (sends Basic Set command frames).
3
5
3rd Association Group – “Tamper” is assigned to the TMP switch (sends alarm command frames).
Number
Size (Bytes)
Default Value
Name
Description
1
1
0
Door window state
This parameter allows to set in what state is door window when the magnet is close to the sensor. 0 - closed when magnet near 1 - opened when magnet near
11
1
0
2nd association group triggers
Parameter defines events which result in sending on-off commands to devices added to the 2nd association group. These commands are sent alternately to switch the devices on and off. 0 - switch after opening and closing 1 - switch after opening (parameter 12) 2 - switch after closing (parameter 13)
12
2
255
Association for opening - value sent
Value sent to devices in 2nd association group when opening is detected. The value of 0 turns OFF the device, 255 turns it On. In case of associating devices allowing smooth control, values 1-99 allow to set an associated device to a specified level.
13
2
0
Association for closing - value sent
Value sent to devices in 2nd association group when closing is detected The value of 0 turns OFF the device, 255 turns it On. In case of associating devices allowing smooth control, values 1-99 allow to set an associated device to a specified level.
14
2
0
Association for opening - time delay
Time that must elapse from opening to send the command frame to to devices in 2nd association group. 0-32400 - time in seconds
15
2
0
Association for closing - time delay
Time that must elapse from closing to send the command frame to devices in 2nd association group. 0-32400- time in seconds
2
1
0
Visual LED indications
This parameter defines events indicated by the visual LED indicator. Disabling events might extend battery life. 1 - indication of opening-closing status change 2 - indication of wake up (1 x click or periodical) 4 - indication of device tampering NOTE Parameter 2 values may be combined, e.g. 1+2=3 means that in -dications for opening/ closing and waking up are enabled.
3
1
3
Associations in Z-Wave network Security Mode
This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network Security Mode. It does not apply to 1st group Lifeline. 0 - none of the groups sent as secure 1 - 2nd group On-Off sent as secure 2 - 3rd group Tamper sent as secure 3 - 2nd and 3rd group sent as secure
30
2
5
Tamper - alarm cancellation delay
Time period after which a tamper alarm will be cancelled. 0-32400- time in seconds .
31
1
1
Tamper - reporting alarm cancellation
Reporting cancellation of tamper alarm to the controller and 3rd association group. 0 - do not send tamper cancellation report 1 - send tamper cancellation report
50
2
300
Interval of temperature measurements
This parameter defines how often the temperature will be measured. The shorter the time, the more frequently the temperature will be measured, but the battery life will shorten. 0 - temperature measurements disabled 5-32400 - time in seconds
51
2
10
Temperature reports threshold
This parameter defines the change of temperature in comparison with last reported, resulting in temperature report being sent to the main controller. 0 - temperature reports based on threshold disabled 1-300 - temperature threshold (0.1-30C, 0.1C step) NOTE Parameter 51 is active only if parameter 50 is not set to 0. Temperature measurement is performed before sending any report (regardless of parameter no. 50). Excessive reporting can affect battery lifetime. Reporting on the basis of temperature change (parameter no. 51) is recommended.
52
2
0
Interval of temperature reports
This parameter determines how often the temperature reports will be sent to the main controller (regardless of parameters 50 and 51). 0 - periodic temperature reports disabled 300-32400 - time in seconds
53
2
0
Temperature offset
The value to be added to the actual temperature, measured by the sensor (temperature compensation). - 1000–1000 (-100–100C, 0.1C step)
54
1
0
Temperature alarm reports
Temperature alarms reported to the Z-Wave controller. Thresholds are set in parameters 55 and 56. 0 - temperature alarms disabled 1 - high temperature alarm 2 - low temperature alarm 3 - high and low temperature alarms enabled.
55
2
350
High temperature alarm threshold
If temperature is higher than set value, overheat notification will be sent and high temperature scene will be triggered (if activated). 1-600 (0.1-60C, 0.1C step)
56
2
100
Low temperature alarm threshold
If temperature is lower than the set value, underheat notification will be sent and low temperature scene will be triggered (if activated). 0-599 (0-59.9C, 0.1C step)
Basic
COMMAND_CLASS_BASIC
Notification V5
COMMAND_CLASS_NOTIFICATION_V5
Application Status
COMMAND_CLASS_APPLICATION_STATUS
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Battery
COMMAND_CLASS_BATTERY
Configuration
COMMAND_CLASS_CONFIGURATION
CRC16 Encapsulation
COMMAND_CLASS_CRC_16_ENCAP
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V4
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Notification V5
COMMAND_CLASS_NOTIFICATION_V5
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Sensor Multilevel V5
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
Version V2
COMMAND_CLASS_VERSION_V2
Wake Up V2
COMMAND_CLASS_WAKE_UP_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Exclusion
1) Place the Door/Window Sensor 2 within the direct range of your Z-Wave controller.

2) Set the main controller into remove mode (see the controller’s manual).

3) Quickly, three times press one of the TMP buttons (while the other button is pressed).

4) Wait for the removing process to end.

5) Successful removing will be confirmed by the Z-Wave controller’s message.



Device Wake-Up
The Door/Window Sensor 2 needs to be woken up to receive informa¬tion about the new configuration from the controller, like parameters and associations.

1) To wake up the sensor manually, click one of the TMP buttons (while the other button is pressed).

Inclusion
1) Place the Door/Window Sensor 2 within the direct range of your Z-Wave controller.

2) Set the main controller in (security/non-security) add mode (see the controller’s manual).

3) Click the Button at least six times.

4) Quickly, three times press one of the TMP buttons (while the other button is pressed).

5) Wait for the adding process to end.

6) Successful adding will be confirmed by the Z-Wave controller’s message.

Factory Reset
Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. In order to reset the device:

1) Open the cover.

2) Remove the battery.

3) Install the battery while holding both TMP buttons.

4) Release the TMP button within 5 seconds.

5) Visual indicator will blink 3 times to confirm launching of reset procedure.

6) Wait around 30s for the resetting process to end, do not remove the battery.

7) Visual LED indicator will blink 6 times to confirm the reset.



*Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use reset procedure only if the primary controller is missing or inoperable.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).
Battery Quantity
Enter the number of batteries of the designated type that the product uses.
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Sensors
Sensor types supported by the product.

 

Reviews

Write a review

FIBARO Door / Window Sensor 2 Opening and temperature detector for door / window Z-Wave Plus

FIBARO Door / Window Sensor 2 Opening and temperature detector for door / window Z-Wave Plus

Z-Wave + opening detector available in various colors for doors, windows, roof windows, etc. ElFIBARO Door / Window Sensor 2 for door / window combines the functionality of two devices: a contact and temperature sensor in a single product Easy to use. It also has a double protection against sabotage.

9 other products in the same category:

Customers who bought this product also bought: