Viewed products





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es
Aeon Labs Smart Energy Monitor View larger

Aeotec Consumer Measurement Clamp - 3 Z-Wave + GEN5 clamps (60A)

AEO_ZW0953C60A

New

Power consumption meter of Z-Wave 3-clamp meter technology for measuring consumption of Aeon Labs, for electrical currents up to 60 amps per clamp.

More details

In Stock

113,99 €

Technical characteristics

Technology Z-Wave Plus
Characteristic Consumption Measurement

More info

Aeon Labs Intelligent Energy Consumption Monitoring Clamps is a low cost electric consumption meter for the home or office. It can wirelessly report the instantaneous use of watts and kWh and send the information to the home automation controller and can be easily installed. Installed in a register box or electrical box, the energy meter will control the total electricity consumption used by an entire building, plants or circuits. The smart clamp will report when the power usage returns to a control point, in watts or kilowatt-hours, and in real time. So you can see how much electricity you actually use and when you use it. The home automation controller will be able to present the information stored to you over time in the form of graphs, depending on what the home automation controller with which it works is able to do ....

The main body is anchored using a back support. The device is powered from a normal AC power source. The device has a clamp and reports W and kWH (up to 60 Amps).

Easy to install, wirelessly informs the energy consumption of the whole house to a domotic controller based on Z-Wave: watts and kW / h. It is connected to the electrical panel of the home or business to control all its electrical consumption, even in real time. Therefore it is a perfect tool to know how much electricity is consumed and when.

This device works through Z-Wave protocol, and there are variants of this same equipment with more or less clamps (depending on what you want to control) and different amperage limits. It allows to know in real time the consumption of one or several phases of a switchboard or electrical circuit, and is a very useful tool to collect readings or more or less constant studies to installers or energy managers, because it allows to reach conclusions quickly and be able to take measures to reduce energy expenditure in electricity.

Electric consumption meter

Remote monitoring via electric consumption meter via Z-Wave

Energy meter for the whole house or low cost trade (power and kWh)

Powered to 220V

Z-Wave Plus Technology

Extended Z-Wave info

Name: Home Energy Meter Gen5
Manufacturer:Aeotec
Identifier:ZW095-C
Z-Wave Certification Number:ZC10-16105288
Hardware Plattform:ZM5202
FLiRS:NO
Role Type:Always On Slave
Short Description:Aeon Labs Home Energy Meter Gen5 is a smart energy meter, which can monitor the total amount of electricity of your home. This HEM G5 has 3 metering channels and supports the installation on 3 phases 4 wire or 3 phases 3 wire power system.
Description:Aeon Labs Home Energy Meter Gen5 is a Z-Wave device that can monitor the total amount of electricity of your home. It can report the wattage energy usage and KWH usage to a Z-Wave Controller (especially a gateway). In near real-time you’ll have a full understanding of how much electricity you use and when you use it. Products that are Z-Wave certified can be used and communicate with other Z-Wave certified devices. Also a tool that can be programmed, scheduled, controlled and communicated with from anywhere in the world.

Manual download HERE.

Group
Max Nodes
Description
1
5
Z-Wave Plus Lifeline. The automatic reports (configured by parameter 101/102/103) can be sent to the associated nodes in association group 1.
Number
Size (Bytes)
Default Value
Name
Description
10
1
10
Percentage change in wattage to induce a automatic report
Percentage change in wattage to induce a automatic report for the power report of Clamp 2.
101
4
2
To set which report need to be sent.
To set which report need to be sent in Report group 1.
102
4
1
To set which report need to be sent.
To set which report need to be sent in Report group 2.
103
4
0
To set which report need to be sent.
To set which report need to be sent in Report group 3.
11
1
10
Percentage change in wattage to induce a automatic report
Percentage change in wattage to induce a automatic report for the power report of Clamp 3.
111
4
5
Set the interval time of sending report.
Set the interval time of sending report in Report group 1.
112
4
120
Set the interval time of sending report.
Set the interval time of sending report in Report group 2.
113
4
120
Set the interval time of sending report.
Set the interval time of sending report in Report group 3.
2
1
0
Set the energy detection mode for parameter 101 to 103.
Set the energy detection mode for the measure reports of parameter 101 to 103.
200
1
0
Partner ID
Partner ID.
252
1
0
Enable/Disable Lock Configuration
Enable/Disable Lock Configuration.
255
4
0
Reset to default factory setting
Reset to default factory setting.
3
1
1
Enable/disable selective reporting only when power change reaches a certain threshold or percentage
Enable/disable selective reporting only when power change reaches a certain threshold or percentage set in parameter 4 to 11.
4
2
50
Threshold change in wattage to induce a automatic report
Threshold change in wattage to induce a automatic report for total power report.
5
2
50
Threshold change in wattage to induce a automatic report
Threshold change in wattage to induce a automatic report for the power report of Clamp 1.
6
2
50
Threshold change in wattage to induce a automatic report
Threshold change in wattage to induce a automatic report for the power report of Clamp 2.
7
2
50
Threshold change in wattage to induce a automatic report
Threshold change in wattage to induce a automatic report for the power report of Clamp 3.
8
1
10
Percentage change in wattage to induce a automatic report
Percentage change in wattage to induce a automatic report for total power report.
9
1
10
Percentage change in wattage to induce a automatic report
Percentage change in wattage to induce a automatic report for the power report of Clamp 1.
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
CRC16 Encapsulation
COMMAND_CLASS_CRC_16_ENCAP
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V4
COMMAND_CLASS_METER_V4
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Factory Reset
Press and hold the Action button that you can find on the product's housing for 10 seconds and then release. This procedure should only be used when the primary controller is inoperable.
Additional Special Features
Support ""Over the Air Firmware Updating"" and “Z-Wave Security”.
Inclusion
Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Action button that you can find on the product's housing.
Exclusion
Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Action button that you can find on the product's housing.
Supported Meter Type
Indicate which type of metering is supported by the device.
Color
If the product is only available in one color, pick the color from the list.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

 

Reviews

Write a review

Aeotec Consumer Measurement Clamp - 3 Z-Wave + GEN5 clamps (60A)

Aeotec Consumer Measurement Clamp - 3 Z-Wave + GEN5 clamps (60A)

Power consumption meter of Z-Wave 3-clamp meter technology for measuring consumption of Aeon Labs, for electrical currents up to 60 amps per clamp.

10 other products in the same category:

Customers who bought this product also bought: