Viewed products





Confianza Online


Qubino Smart Meter 3 phases - 3-phase Z-Wave Plus electric consumption meter for DIN rail

ZMNHXD1

New

Qubino's three-phase smart DIN electric power meter is used for energy measurements in three-phase power grids.
It reduces energy consumption, decreases the bills of public public administrations and improves efficiency in residential, industrial and public service applications.

More details

In Stock

169,90 €

Technical characteristics

Technology Z-Wave Plus

More info

Extremely powerful three-phase power meter

Reduce energy consumption

The Qubino three-phase smart meter is used for energy measurements in three-phase electrical networks.
It reduces energy consumption, decreases utility bills and improves efficiency in residential, industrial and public service applications.

Three Phase Qubino Smart Meter 3 Phase Consumption Meter

How can the three-phase smart meter be used?

The three-phase Qubino Smart Meter can be used in many different scenes, which can help make your life more comfortable.
There are countless options to use the Qubino three-phase smart meter to remotely measure the power consumption
of your home or connected devices.

  • Track the energy consumption of the entire house and measure 9 different electrical values.
  • Track the energy consumption of a three-phase electrical device (for example, a three-phase heat pump) and measure up to 9 different electrical values.
  • Track the energy consumption of a three-phase electrical device (for example, an induction furnace) and measure up to 9 different electrical values.
  • Measure 3 different electrical values (V, A, W) in each phase, plus 5 electrical values in common (Kwh, Kvar, KVarh, kVAh, PF).
  • Remotely control and measure the energy consumption of 3 phases of an electrical device. The device (heat pump, for example) can be controlled with an external contactor.
  • Remotely control and measure the energy consumption of 3 phases of an electrical device. The device (induction furnace, for example) can be controlled with an external contactor.
  • Remotely control and measure the energy consumption of 3 phases of an electrical device (for example, accurate information on the energy consumption of the electric car). The device (for example: electric charger for electric car) can be controlled with an external contactor.
  • Remotely measure the energy consumption of the entire house and control a group of electrical devices (for example: lights) with an external contactor.
  • Track the energy consumption for each of the three electrical devices and control two groups of electrical devices (for example: three-phase heat pump and lights) with external contactors.
  • Measure remotely the energy consumption of the whole house and the control of the electrical devices of the groups (for example: heat pump and lights) with external contactors.

Main advantages

It is an extremely versatile and powerful Z-Wave device for measuring energy in a three-phase power network of up to 3 x 65A.

The only three-phase intelligent meter in the world that allows the connection of additional relay contactors and DIN rail support.

Some devices in your home consume too much energy

The three-phase Smart Meter can automatically turn off the devices / lights after they exceed the set power consumption. For example, the heating will automatically turn off after reaching the set power consumption value. This function is independent of other scenes and gateway commands (hub).

Control other devices in your Z-Wave network

Connect the three-phase smart meter with other devices in your network to remotely and automatically activate another Z-Wave device. And have other Z-Wave devices power your Qubino 3-Phase Smart Meter.

The simplest installation

There is no simpler installation than the DIN rail installation, and the Qubino three-phase smart meter is a device mounted on a DIN rail.

Technical specifications

Three phase meter of Qubino Smart Meter 3 Phase

Main terminals (L1 I , L2 I , L3 I , N I , L1 O , L2 O , L3 O , N O )
Contacts capacity: 2.5 ... 16 (25) mm 2
Connection screws: M5
Max torque: 3.5 Nm (PZ2)
Optional terminals (DI, DO)
Contact capacity: 1 ... 2.5 mm 2
Screws: M3
Max torque: 1.2 Nm
Measuring input:
Type (connection): three phase (4u)
Basic current (Ib): 5 A
Maximum current (Imax): 65 A
Minimum current (Imin): 0.25 A
Starting current: 20 mA
Nominal voltage (Un): 230V (+ 15-20%)
Power at Un: <8 VA
Nominal frequency (fn): 50 and 60 Hz
Accuracy:
Active energy and power:
Standard EN 62053-21: class 1
Standard EN 50470-3: class B
Reactive energy:
Standard EN 62053-23: class 2
LED:
Color: net
Pulse rate: 500 imp / kWh
Led on: no load indication
Optical communication:
Type: IR - used to control BICOM432-40-IR
Digital Input (16):
Rated voltage: 230 V (± 20%)
Digital Output (15):
Rated voltage: 230 V (± 20%)
LCD:
Display 7 + 1 digit (100Wh resolution)
Safety:
Indoor Meter: And it is
Degree of pollution: 2
Protection class: II
AC voltage test: 4 kV
Installation Category: 300 VRMS Cat. III
Standard: EN 50470
Ambient conditions and EMC: Meets standards for indoor active energy meters. Temperature and climatic conditions to EN 62052-11
Ambient conditions and Safety: Meets standards for indoor active energy meters. Temperature and climatic conditions to EN 62052-11
Dust / water protection: IP20
Operating temperature: -10 ... 55 ° C
Storage temperature: -40 ... 70 ° C
Enclosure material: self-extinguishing
complying UL94 V
UL94 V compliant And it is
Indoor meter: And it is
Degree of pollution: 2
AC voltage test: 4 kV
Standard: EN 50470
Distance: up to 30 m indoors (depending on building materials)
Weight (with packaging): 220 g (240 g)
Frequency range: 868.4 MHz *, Z-Wave
Installation Din rail 35 mm (EN 60715)
Dimensions (WxHxD): 53.6 x 84 x 65 mm
Package dimensions (WxHxD): 56 x 86 x 70 mm
Color: RAL 7035
EC Directives conformity:
EC Directive on Meas. Instruments 2004/22 / EC
EC Directive on EMC 2004/108 / EC
EC Directive on Low Voltage 2006/95 / EC
EC Directive WEEE 2002/96 / EC

* Depends on ordering code

Box contents

Practical lightweight cardboard packaging guarantees a lower delivery cost.
The package contains 1 module and 1 user manual.

Dimensions of the package (WxHxD): 53.6 x 84 x 65 mm
Gross weight (including packaging): 240 g

Additional parameters for professionals

There are 16 additional parameters for expert users. Some of the most useful are:

Input switch function selection
Automatic start / stop of the external relay after the set exit time
Reports in Watts about the change of energy or time intervals

Setting Parameters

Parameter no. 7 Input 1 switch function selection

Available configuration parameters (data type is 1 DEC Byte):

default value 4

  • 0 - disabled
  • 1 - Tariff input
  • 2 - IR external relay control mono stable push button
  • 3 - IR external relay control - bi stable switch
  • 4 - External relay control mono stable push button
  • 5 - External relay control bi stable switch

Parameter no. 40 Reporting on power change

Set value means percentage, set value from 0 100 = 0% - 100%. Available configuration parameters (data type is 1 DEC Byte):

    • default value 10
    • 0 - reporting disabled
    • 1 - 100 = 1% - 100% Reporting enabled. Power report is sent (pushed) only when current power in Watts in real time changes for more than set percentage comparing to previous current power in Watts, step is 1%.

NOTE: If power changed is less than 1 W, the report is not sent (pushed)

NOTE: when W is changed for more than percent value in this parameter -> the module is reporting also:

  • A (if the value has changed)
  • V (if the value has changed)
  • Power factor (if the value has changed)
  • kVar (Reactive power) (if the value has changed)

The module is measuring some disturbances even if the output is not load. To avoid unintended reporting: If measured active power (W) is below 5 W -> the value is not reported.

Parameter no. 42 Reporting on time interval

Available configuration parameters (data type is 2 Byte DEC):

  • default value 600 (10 minutes)
  • 0 - Reporting Disabled
  • 10 - 32535 = 10 seconds - 32535 seconds. Reporting enabled. Report is sent with the time interval set by entered value.

NOTE: The module is reporting following values (if there was a change):

  • kWh (import / export)
  • kVarh
  • kVAh
  • W, A, V, PF, kVar

NOTE: If measured active power (W) is below 5W -> the value is reported on time interval.

Parameter no. 106 External IR relay (BICOM) power threshold settings maximum power of all phases together

This parameter defines a threshold when External IR relay is being turned off. (If Parameter No. 100 is set to the value 1 or 2)
Available configuration parameters (data type is 2 Byte DEC)

  • Default value 0
  • 0 no function
  • 10-60000 10W-60000W
    NOTE: Meter is capable of measuring max 3x80A!

Parameter no. 107 External relay (IKA) power threshold settings maximum power on phase L2

This parameter defines a threshold when External relay is being turned off (if the parameter No. 100 is set to the value 1 or 2).
Available configuration parameters (data type is 2 Byte DEC)

  • Default value 0
  • 0 no function
  • 10-20000 10W-20000W
    NOTE: Meter is capable of measuring max 80A

Parameter no. 112 Overload on External Relay Delay before power on

External relay is turned off due to detected overload on L1, L2 or L3 (Parameter no.110). It remains off for a time, defined in this parameter. After that time, the output is turned on for a short time to check, if overload is still presented.

Available configuration parameters (data type is 2 Byte DEC):

  • Default value 300 (5 minutes)
  • 0 relay configuration if both relays are connected to the same Phase (see the table in Parameter No. 113)
  • 10-32535 10s - 32535s

Download

Extended Z-Wave info

Name: 3-Phase Smart Meter
Manufacturer:QUBINO
Identifier:ZMNHXD1
Z-Wave Certification Number:ZC10-19066549
Hardware Plattform:ZM5101
FLiRS:NO
Role Type:Always On Slave
Short Description:The 3-Phase Smart Meter is a powerful Z-Wave device for measuring energy consumption in a three-phase electrical power network of up to 3 x 65A.
Description:The Qubino 3 Phase Smart Meter can be used in residential, industrial and utility applications. It measures energy directly in 2-wire networks by means of fast sampling of voltage and current signals. It calculates energy, power and power factor from the measured signals. You can control the device through the Z-Wave network. The Qubino 3 Phase Smart Meter can operate across a wide temperature range, from a chilly -15˚C to a scorching 55˚C (5˚F–131˚F). Every device also acts as a repeater in order to improve the range and stability of the Z-Wave network.

Manual download HERE.

Group
Max Nodes
Description
1
1
Supports the following commands: • Device Reset Locally: triggered upon request • Meter Report: triggered according to Configuration parameters 40,42 and 43
Number
Size (Bytes)
Default Value
Name
Description
40
1
50
Reporting on power change
This parameter is valid for Active Power Total, Active Power Phase1, Active Power Phase2 and Active Power Phase3. Set value means percentage from 0-100 = 0% - 100% • Available configuration parameters (data type is 1 Byte DEC) • Default value 50 • 0 – reporting disabled • 1-100 = 1% - 100% reporting enabled. Power report is send only when actual power in Watts (in real time changes for more than set percentage comparing to previous Active Power, step is 1%. NOTE: if power change is less than 5 W, the report is not send (pushed). NOTE: Device is measuring also some disturbances even if on the output is no load. To avoid disturbances: • If measured Active Power (W) is below e.g. 5W-> the reported value in this case is 0W
42
1
600
Reporting on time interval
This parameter is currently valid only for Active Energy Total Import/Export (kWh), Reactive Energy Total (kvarh), Total Energy (kVAh) • Available configuration parameters (data type is 2 Byte DEC) • Default value 600 (600 seconds - 10 minutes) • 0 – reporting disabled EN. 34 • 600-32535 = 600 (600 seconds – 32535 seconds). Reporting enabled. Report is send with the time interval set by entered value. Note: Device is reporting only if there was a change of 0.1 in Energy Note: In the future will be possible to measure and report also Active Energy on PH1, PH2 and PH3.
43
2
600
Other Values - Reporting on time interval
This parameter is valid only for Voltage (V of ph1, ph2, ph3), Current (A of ph1, ph2, ph3), Total Power Factor, Total Reactive Power (var) Available configuration parameters (data type is 2 Byte DEC) • Default value 600 (600 seconds - 10 minutes) • 0 – reporting disabled • 600-32535 = 600 (600 seconds – 32535 seconds). Reporting enabled. Report is send with the time interval set by entered value. • Note: Device is reporting only if there was a change
Association Group Information V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Configuration
COMMAND_CLASS_CONFIGURATION
CRC16 Encapsulation
COMMAND_CLASS_CRC_16_ENCAP
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V4
COMMAND_CLASS_METER_V4
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Supervision
COMMAND_CLASS_SUPERVISION
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Exclusion
EXCLUSION:

1. Connect the device to the power supply

2. Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion

3. Enable add/remove mode on your Z-Wave gateway (hub)

4. Press and hold the S service button between 0.2 and 3 seconds

5. The device will be removed from your network, but custom configuration parameters will not be erased. Wait at least 30 seconds before attempting to add the device back to a network.
Inclusion
AUTOMATICALLY:

1. Enable add mode on your Z-Wave gateway (hub). Put the device in a mode, in which it can be added to a network (learn mode)

2. Automatic selection of secure/unsecure inclusion

3. The device can be automatically added to a Z-Wave network during the first 2 minutes

4. Connect the device to the power supply

5. Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the device will be automatically added to your network



MANUALLY:

1. Connect the device to the power supply

2. Enable add/remove mode on your Z-Wave gateway (hub)

2. Toggle the Service button S between 0.2 and 3 seconds

3. A new multi-channel device will appear on your dashboard
Factory Reset
FACTORY RESET:

1. Connect the device to the power supply

2. Press and hold the S service button between 6 seconds and 20 seconds

3. Device will be removed from you network and the green LED start blinking



By resetting the device, all previously set parameters on the device will return to their default values, and the Home ID will be deleted. Use this reset procedure only when the main

gateway (hub) is missing or otherwise inoperable.

S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps
Loads Controlled
The number of different loads controllable by the product if it supports more than one.
Switch Load Capacity Watts
The amount of switch load energy the product is rated for in Watts
IP (Ingress Protection) Rated
Product is suitable for Outdoor use and is waterproof under an IP (Ingress Protection) rating system.
Supported Meter Type
Indicate which type of metering is supported by the device.
Electric Load Type
Select the electric load type(s) supported by the device.
Communications Protocol
For external interfaces, choose the communications protocol used.
Neutral Wire Required
For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.
Switch Type
Describes the type of operator for a switch.
Color
If the product is only available in one color, pick the color from the list.

 

Reviews

Write a review

Qubino Smart Meter 3 phases - 3-phase Z-Wave Plus electric consumption meter for DIN rail

Qubino Smart Meter 3 phases - 3-phase Z-Wave Plus electric consumption meter for DIN rail

Qubino's three-phase smart DIN electric power meter is used for energy measurements in three-phase power grids.
It reduces energy consumption, decreases the bills of public public administrations and improves efficiency in residential, industrial and public service applications.

Accessories

18 other products in the same category:

Customers who bought this product also bought: