Viewed products





Confianza Online


Fibaro Flood Sensor - Flood Detector Z-Wave Plus

FIB_FGFS-101-ZW5

New

Fibaro's Z-Wave Plus Flood Detector, which alerts you to a flood threat due to water spillage, ponding or a rapid change in temperature.

More details

In Stock

59,99 €

Technical characteristics

Technology Z-Wave Plus

More info

With a compact and futuristic design, in addition to its small size, this Fibaro flood sensor warns you of a flood threat, or a rapid change in temperature. It is a Z-Wave + device that is very suitable to protect the whole family. This ZWave flood detector also detects the temperature. It can be powered by battery or by an external power supply of 12 or 24 V (DC). If it is connected to an external power source, the battery is a source of backup power. The flood warning is sent to the Z-Wave device network or to any cable alarm system through the dry contact (NC) output.

This ZWave flood detector includes a temperature sensor. It also has an LED and an audible alarm. In addition, this ZWave device is equipped with a motion sensor to detect movements or tilt, reporting it to the main controller, for example, when someone moved the sensor from its original location. The LED indicates a flood, as well as the mode or range of communications of the Z-Wave network.

This Fibaro flood sensor is submersible, and tends to come to the surface of the water, while still sending the alarm signal in case of large amounts of water in a flood. It has been designed to be placed on the floor, although it can also be installed on a wall using a probe connected by cable.

For your safety and to ensure that the flood detector is working properly, a test function of the ZWave network is available. The communication in the Z-Wave wireless network, allows the sensor to stay connected with the control unit even through great distances thanks to the indirect connectivity with other Z-Wave modules installed in the house. The integrated LED allows you to easily check whether the sensor has a good connection to communicate with the control unit or requires a different location.

CHARACTERISTICS:

  • Flood and temperature detector Z-Wave PLUS (Fibaro names it as ZW5)
  • Can be connected to any alarm system (dry contact output)
  • Can be installed anywhere - the flood sensor can be extended with a cable probe
  • Powered by external power supply and / or battery
  • Protection against theft or tampering - the tilt is displayed on the control unit of the Z-Wave network or alarm system
  • Two operating modes: flood / temperature sensor or only temperature sensor
  • Integrated Z-Wave network coverage test
  • Updates of the device through the Z-Wave wireless network and the Fibaro Home Center2 or HC Lite
  • Simple installation - just put it in a flood prone area

SPECIFICATIONS:

  • Module Type: Z-Wave transmitter
  • Power supply: 12 to 24 VDC
  • Battery type: CR123A
  • Battery life: 2 years
  • External power consumption: 0.4 W
  • Maximum admitted output current (NC ALARM, NC TAMP): 25 mA
  • Rated maximum output voltage: 40 V (AC or DC)
  • Frequency: 868.42 MHz
  • Transmission distance: 50 m free field, 30 m indoors
  • Dimensions: 72 x 28 mm (diameter x height)
  • Temperature: 0-40 ° C (-20 ° C to 70 ° C if the external power supply)
  • Range of temperature measurement: -20 to 100 ° C
  • Measurement accuracy: 0.5 ° C (in a range of 0 to 40 ° C)
  • Standards: EMC 2004/108 / CE and R & TTE 199/5 / WE

Z-Wave Plus - Fibaro ZW5

Extended Z-Wave info

Name: FIBARO Flood Sensor
Manufacturer:FIBARO
Identifier:FGFS-101
Z-Wave Certification Number:ZC10-19076588
Hardware Plattform:ZM5202
FLiRS:NO
Role Type:Reporting Sleeping Slave
Short Description:FIBARO Flood Sensor is a universal, battery or VDC powered, Z-Wave Plus compatible, flood and temperature sensor, designed to be placed on a floor or on a wall.
Description:FIBARO Flood Sensor is a universal, Z-Wave Plus compatible, flood and temperature sensor. The device can be powered using battery, 12/24V DC power supply or both. Flood alarm is sent to the Z-Wave network devices or additionally to any alarm system controller through opening a NC contact using the external power supply. The device has a built-in temperature sensor that allows to monitor ambient temperature. FIBARO Flood Sensor is designed to be placed on the floor or mounted on a wall (in this case Flood Sensor probes should be extended using addition wire). The device has a built-in visual LED indicator and an acoustic alarm. The LED indicator signals flood, operating mode or the Z-Wave network communication range. In addition, the device is equipped with a sensor reporting tilt or movement to the main controller e.g. when someone has taken the Sensor from its original location. FIBARO Flood Sensor is sink-proof, which means it drifts on the water surface and keeps on sending alarm signal in case of substantial inundation of water (if not wired). Flood Sensor is compatible with any Z-Wave or Z-Wave Plus Controller.

Manual download HERE.

Group
Max Nodes
Description
1
1
“Lifeline” reports the device status and allows for assigning single device only (main controller by default).
2
5
“Flood Control” devices in this group will be switched on or off when flood status changes (done via BASIC SET command frames).
3
5
“Flood Alarm” is assigned to the device status - devices in this group will receive notification about flood detection or cancellation. Useful for devices that can trigger alarms.
4
5
“Tamper Alarm” is assigned to the TMP button and tilt sensor - devices in this group will receive a notification when the sensor is moved or the cover is taken off (which normally holds the button). Useful for devices that can trigger alarms. Functionality can be altered by parameter 74.
Number
Size (Bytes)
Default Value
Name
Description
1
2
0
Alarm cancellation delay
Determines time period (in seconds) by which a Flood Sensor will retain the flood state after the flooding itself has ceased. The sensor will keep on reporting flooding to the main controller. This parameter setting does not affect acoustic and visual alarms, which turn off immediately after flooding ceases.
10
4
300
Temperature measurement interval
Time interval (in seconds) between consecutive measurements of battery level and temperature (done by built-in temperature sensor). If the temperature differs from previously reported by a value determined in parameter 12, it will be reported to the Z-Wave controller. In battery mode more significant battery level changes will be reported. Short time intervals mean more frequent communication, which results in shortened battery life. After consecutive FAILED and SUCCESSFUL communication attempts, the Sensor will go to standby mode.
12
2
50
Temperature measurement hysteresis
Determines a minimum temperature change value (insensitivity level), resulting in a temperature report being sent to the main controller, according to the parameter 10 settings.
2
1
3
Acoustic and visual signals On / Off in case of flooding
The parameter allows for deactivation visual and acoustic alarm. Parameter allows for increasing a battery life. Setting changes will not affect the sensor’s communication with the main controller - commands to association groups, alarms and reports will still be sent.
50
2
1500
Low temperature alarm threshold
The parameter stores a temperature value, below which visual indicator blinks with a colour determined by a parameter 61 settings. By default the visual indicator blinks blue.
51
2
3500
High temperature alarm threshold
The parameter stores a temperature value, above which visual indicator blinks with a colour determined by the parameter 62 settings. By default the visual indicator blinks red.
61
4
255
Low temperature alarm indicator colour
Parameter stores RGB colour value (see the note below for details).
62
4
16711680
High temperature alarm indicator colour
Parameter stores RGB colour value (see the note below for details). NOTE The main controller interprets colours as a sum of its component colours value. Each colours value is a number from 0 to 255. Indicated colour = 65536 RED + 256 GREEN + BLUE Colour Decimal value Red 16711680 Green 65280 Blue 255 Yellow 16776960 Turquoise 65535 Orange 16750848 White 16777215 Indicator turned off 0
63
1
2
Temperature indication using LED visual indicator
Parameter determines visual indicator’s operation. Setting to 0 turns the temperature LED indication off, saving battery life.
7
2
255
Requested dimming level / roller blind opening level when sending turn on / open command to 2nd association group devices
Determines the requested “on” level to be sent to devices from 2nd association group upon flood event.
73
2
0
Temperature measurement compensation
Parameter stores a temperature value to be added to or deducted from the current temperature measured by internal temperature sensor in order to compensate the difference between air temperature and temperature at the floor level.
74
1
2
Alarm frame sent to 1st and 4th Association Group activation
(MOVEMENT_TAMPER / BUTTON_TAMPER) The device is able to report tamper alarms resulting from sensor’s tilt/movement or TMP button state change (e.g. taking off the top cover).
75
4
0
Alarms signalization duration
The device is capable of automatically turning off alarm signalization after a certain amount of time. Long lasting alarm may reduce batter life, when constantly signalized. The parameter determines time after which alarm will become “quiet” - still active but the device will go into battery saving mode. Visual or acoustic alarm will be reactivated after time specified in the parameter 76. When alarm status ceases, alarm will be turned off immediately. NOTE Parameter 75 is ignored when parameter 2 is set to 0.
76
4
0
Alarm signalization reactivation period
Parameter determines a time period after which an alarm will be turned back on (in case it was turned off by parameter 75 setting). It will also resend commands to 2nd and 3rd association groups as if the alarm was detected again. NOTE In case a time period set in parameter 76 is shorter than the one specified in parameter 75, the device will not quiet the alarm, it will remain active.
77
1
0
Flood sensor functionality turned off
Allows to turn off the internal flood sensor. Tamper and built in temperature sensor will remain active.
78
1
7
Associations in Z-Wave network security mode
This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. It does not apply to 1st “Lifeline “group.
9
1
1
Deactivate turning off devices in 2nd association group & alarm cancellation in 3rd group
This setting decides whether device turn off commands and alarm cancellation notifications will be sent to devices in 2nd and 3rd association groups (respectively) Setting the parameter’s value to 0 disables sending these two commands to associated devices. This means that these devices WILL NOT be informed when the flooding has ceased. It is still possible to cancel alarms in 3rd association group by choosing second (green) menu position (see “Menu & visual indications” on page 10).
Basic
COMMAND_CLASS_BASIC
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Application Status
COMMAND_CLASS_APPLICATION_STATUS
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Battery
COMMAND_CLASS_BATTERY
Configuration
COMMAND_CLASS_CONFIGURATION
CRC16 Encapsulation
COMMAND_CLASS_CRC_16_ENCAP
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V3
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V3
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi Channel Association V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2
Notification V5
COMMAND_CLASS_NOTIFICATION_V5
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Sensor Alarm
COMMAND_CLASS_SENSOR_ALARM
Sensor Multilevel V5
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
Version V2
COMMAND_CLASS_VERSION_V2
Wake Up V2
COMMAND_CLASS_WAKE_UP_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Inclusion
1) Open the cover by turning it counter-clockwise.

2) Remove battery blocker.

3) Place the device within the direct range of your Z-Wave controller.

4) Set the main controller in (security/non-security) add mode (see the controller’s manual).

5) Quickly, triple click the TMP button located inside the casing.

6) Wait for the adding process to end.

7) Successful adding will be confirmed by the Z-Wave controller’s message.

8) Close the cover by turning it clockwise.

9) Place the sensor onto a surface prone to flooding. Three electrodes underneath the device should evenly touch the surface.

Exclusion
1) Open the cover by turning it counter-clockwise.

2) Make sure the device is powered (either by a battery or a DC power supply).

3) Place the device within the direct range of your Z-Wave controller.

4) Set the main controller in remove mode (see the controller’s manual).

5) Quickly, triple click the TMP button located inside the casing.

6) Wait for the removing process to end.

7) Successful removing will be confirmed by the Z-Wave controller’s message.

Factory Reset
1) Open the cover by turning it counter-clockwise.

2) Make sure the device is powered (either by a battery or a DC power supply).

3) Press and hold the TMP button for 15-20 seconds until LED glows yellow (4th menu position).

4) Release and click the TMP button to start the reset procedure.

5) Successful reset will be confirmed with the LED indicator changing colour to red and an acoustic signal.

Use reset procedure only if the primary controller is missing or inoperable.

Device Wake-Up
FIBARO Flood Sensor will wake up at a defined time interval and will always try to communicate with the main controller. There is a possibility to wake up the device manually by clicking the TMP button
Color
If the product is only available in one color, pick the color from the list.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Sensors
Sensor types supported by the product.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).
Battery Quantity
Enter the number of batteries of the designated type that the product uses.
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.

 

Reviews

Grade 
02/20/2019

Inundacion a raya

Facil de poner y configurar en mi Home Center Lite. Me lego rapido.

Write your review!

Write a review

Fibaro Flood Sensor - Flood Detector Z-Wave Plus

Fibaro Flood Sensor - Flood Detector Z-Wave Plus

Fibaro's Z-Wave Plus Flood Detector, which alerts you to a flood threat due to water spillage, ponding or a rapid change in temperature.

5 other products in the same category:

Customers who bought this product also bought: