Viewed products





Confianza Online


ZIPATO - Enchufe "schuko" on-off con medición de consumo eléctrico Z-Wave Plus View larger

ZIPATO - On-off wallplug with Z-Wave Plus power consumption measurement

ZIP-PAN16-EU

New

The Z-Wave Plus ZIP-PAN16 socket module allows you to control lighting or a device remotely using the Z-Wave protocol while measuring the energy consumed.

More details

In Stock

59,00 €

Technical characteristics

Technology Z-Wave Plus
Characteristic Consumption Measurement

More info

The intelligent Zipato wall outlet makes it easy to control any outlet remotely.

In addition to the switching function, this module can also measure the power consumption of the connected load. You can check the instantaneous consumption values (in W) and the total energy consumption (in kWh).

Equipped with the chip of the Z-Wave 500 series, it enjoys all its advantages with a greater range and speed of communication, as well as a lower power consumption in standby mode.

This Z-Wave module also works as a wireless repeater with other modules, to ensure full coverage of your home. You need a Z-Wave controller (remote control, dongle ...) to integrate this module into your network if you already have an existing network.

FUNCTIONS:

Lighting control / device remotely
It is installed in an existing point of sale
Adopt the Z-Wave Plus 500 SERIES chip.
Optimized antenna range
On / off function
Measurement of instantaneous and cumulative consumption
Overload protection
Automatic consumption report during a variation of 5%
Ease of use and installation

TECHNICAL CHARACTERISTICS :

Module type: Schuko type Z-Wave Plus receiver
Power supply: 230V
Maximum load: 3000W / 13A (resistive load)
Frequency: 868.42 Mhz
Transmission distance: 40 m
Dimensions: 79x51x18 mm
Weight: 107g
Operating temperature: 0-40 ° C

Extended Z-Wave info

Name: Smart energy plug-in switch
Manufacturer:Zipato
Identifier:ph-pan16.eu
Z-Wave Certification Number:ZC10-17055605
Hardware Plattform:SD3502
FLiRS:NO
Role Type:Always On Slave
Short Description:The product documentation states a Security Enabled Z-Wave Controller must be used in order to fully utilize the product. Smart Energy Plug In Switch is a security enabled wireless switch, based on Z-Wave Plus technology.
Description:The product documentation states a Security Enabled Z-Wave Controller must be used in order to fully utilize the product. Smart Energy Plug In Switch is a security enabled wireless switch, based on Z-Wave Plus technology. Z-Wave Plus enabled devices displaying the Z-Wave Plus logo can also be used with it regardless of the manufacturer, and can also be used in other manufacturer’s Z-Wave enabled networks. Remote On/Off control of the connected load is possible with other manufacturer’s wireless Controller. Each switch is designed to act as a repeater. Repeaters will re-transmit the RF signal to ensure that the signal is received by its intended destination by routing the signal around obstacles and radio dead spots. Because the Switch supports Security Command Class, it can learn with Secured controller. Its functionality and supported command classes is identical when included as a secure and non-secure device. This Smart Energy Plug In Switch is able to detect instance wattage (3000W/230Vac) (13Ampere) and overload current (14.5A with resistive load) of connected lights or appliances. When detecting overload state, the Switch will be disabled and its On/Off button will be lockout of which LED will flash quickly. However, unplug and reconnect the switch will reset its overload condition to normal status.

Manual download HERE.

Group
Max Nodes
Description
1
1
Lifeline The Switch can be set to send reports to associated Z-Wave devices. It supports one association group with one node support for Grouping 1. For group 1, the Switch will report its latest status to Z-Wave Controller. Grouping 1 includes, SWITCH_BINARY_REPORT, METER_REPORT, ALARM_REPORT.
Number
Size (Bytes)
Default Value
Name
Description
1
2
720
Watt Meter Report Period
If the setting is configured for 1hour (set value =720), the Switch will report its instant power consumption every 1 hour to Group1 node. The maximum interval to report its instant power consumption is 45 hours (5s*32767/3600=45hr). When the setting is set at 0, the Switch will disable Watt auto report function. The default value is 720.
11
1
1
Manual Switch Report Mode
The default setting is Enable the function. Whenever the Switch is manually switched on or off, it will send BINARY_SWITCH_REPORT to the node of group1.
12
1
1
Auto Report after Reset
Whenever the Switch is repowered, it will check this parameter for if sending a BINARY_SWITCH_ REPORT to the node of group1 or not. The default setting is Disable the function.
13
2
1450
Adjustable overload
The overload current can be adjustable from 4.5A to 14.5A. The default value is 1450 for 14.5A. (1450 * 0.01A = 14.5A).
2
2
6
KWH Meter Report Period
If the setting is configured for 1hour (set value =6), the Switch will report its Accumulated Power Consumption (KW/h) every 1 hour to Group1 node. The maximum interval to report its Accumulated Power Consumption (KW/h) is 227.55 days (10min*32767/1440=227.55 days). When the setting is set at 0, the Switch will disable KWH auto report function. The default value is 6.
3
2
1300
Threshold of current for Load caution
This is a warning when the current of load over the preset threshold value, if the setting value is 1300, when the load current of Relay1 over this value, Swtich will send current meter report to warn the Group1 node, the Range of the setting value is from 10 to 1300,and the default value is 1300.
4
2
10000
Threshold of KWh for Load caution
This is a warning when the KWh of load over the preset threshold value, If the setting value is 10000, when the Accumulated Power Consumption of Relay1 over this value, the Switch will send KWH meter report to warn the Group1 node, minimum value is 1KWh and default value is 10000 kWh.
5
1
1
Restore switch state mode
Whenever the AC power return from lost, the Switch will restore the switch state which could be SWITCH OFF, LAST SWITCH STATE, SWITCH ON. The default setting is LAST SWITCH STATE.
6
1
1
Mode of Switch Off function
When the mode of switch On/Off is set to 0, any command of switch off will be disabled and the On/Off function of include button will be disabled. The default setting is enable mode. When manual On/Off function is disabled, the RF command can only switch On but not Off. This is useful function for keeping the device in switch on state.
7
1
1
LED indication mode
1.SHOW SWITCH STATE: When the Switch is on, LED is on. When the Switch is off, LED is off. The default setting is Show Switch State. 2.SHOW NIGHT MODE: When the Switch is on, LED is off. When the Switch is off, LED is on. 3.ONE FLASH MODE: When the state of the Switch changes, LED will turn on for 1 second.
8
2
0
Auto off timer
Whenever the Switch switches to on, the auto off timer begin to count down. After the timer decrease to zero, it will switch to off automatically. However if Auto off timer is set as 0, the auto off function will be disabled.
9
1
0
RF off command mode
Whenever a switch off command, BASIC_SET, BINARY_SWITCH_SET, SWITCH_ALL_OFF, is received, it could be interpreted as 4 variety of commands. The default setting is Switch Off. 1.SWITCH OFF: It switches to OFF state. The default setting is Switch Off. 2.IGNORE: The switch off command will be ignored. 3.SWITCH TOGGLE: It switches to the inverse of current state. 4.SWITCH ON: It switches to ON state.
Alarm
COMMAND_CLASS_ALARM
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V2
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
Manufacturer Specific
COMMAND_CLASS_MANUFACTURER_SPECIFIC
Meter V3
COMMAND_CLASS_METER_V3
Powerlevel
COMMAND_CLASS_POWERLEVEL
Protection V2
COMMAND_CLASS_PROTECTION_V2
Security S0
COMMAND_CLASS_SECURITY
Switch All
COMMAND_CLASS_SWITCH_ALL
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Factory Reset
Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.

Pressing On/Off button three times within 2 seconds will enter inclusion mode.

Within 1 second, press On/Off button again for 5 seconds.

IDs are excluded.
Inclusion
Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer.

Pressing On/Off button three times within 2 seconds will enter inclusion mode.
Exclusion
Put your Z-Wave controller into exclusion mode by following the instructions provided by the controller manufacturer.

Pressing On/Off button three times within 2 seconds will enter exclusion mode.

Node ID has been excluded.
Electric Load Type
Select the electric load type(s) supported by the device.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps
Supported Meter Type
Indicate which type of metering is supported by the device.
Color
If the product is only available in one color, pick the color from the list.
Switch Type
Describes the type of operator for a switch.

 

Reviews

Write a review

ZIPATO - On-off wallplug with Z-Wave Plus power consumption measurement

ZIPATO - On-off wallplug with Z-Wave Plus power consumption measurement

The Z-Wave Plus ZIP-PAN16 socket module allows you to control lighting or a device remotely using the Z-Wave protocol while measuring the energy consumed.

14 other products in the same category:

Customers who bought this product also bought: