Name: Heatit Z-Dim
Manufacturer:HEATIT
Identifier:Z-Dim
Z-Wave Certification Number:ZC10-19106778
Hardware Plattform:ZM5101
FLiRS:NO
Role Type:Always On Slave
Short Description:Heatit Z-Dim is a Z-Wave rotary dimmer for many different types of light sources.
Heatit Z-Dim can dim to a lower level than traditional dimmers, only 1VA. This dimmer makes you able to set the mood
in any room of your choosing. It also functions as a scene controller, which enables you to use the dimmer for a large number of tasks.
Description:Heatit Z-Dim is a Z-Wave rotary dimmer for many different types of light sources.
The Heatit Z-Dim works on low loads without causing the lights to flicker. It dims LED-bulbs from 1-200VA, 230V halogen and incandescent bulbs, dimable LED-drivers and electronic transformers. The dimmer is not affected by startup inrush currents. L+N leads must be connected.
The dimmer is equipped with a multiway switching option. This allows you to light and dim a light source from one dimmer, and later turn it off with another one. Very practical for stairwells, long hallways etc.
The dimmer fits into standard Gira System 55 frame systems.
Group
Max Nodes
Description
1
8
Z-Wave Plus Lifeline Supports the following command classes:
• Meter Report: triggered according to Configuration
• Switch Multilevel
• Central Scene
• Device Reset Locally: triggered upon request
2
8
Basic Set: triggered at change of output and reflecting its state.
3
8
Binary Switch Set: triggered at change of output and reflecting its ON/OFF state.
Number
Size (Bytes)
Default Value
Name
Description
1
1
0
Connected Load.
The parameter defines the value of connected load.
Refer to Paragraph 8 ”Power Metering”.
10
1
50
Power restore level.
The parameter defines initial dimming level after power loss.
2
1
20
Minimum Dim level.
The parameter defines the lowest dimming level of the dimmer.
The value must be lower than parameter 3 ”Maximum Dim Level”.
3
1
85
Maximum Dim level.
The parameter defines the highest dimming level of the dimmer.
The value must be higher than parameter 2 ”Minimum Dim Level”.
4
1
15
Total steps.
The parameter defines how many steps it should take to dim from minimum to maximum dim level. (One round = 20 steps)
5
1
0
Double press function.
The parameter defines the double press functionality.
6
1
1
Scene controller.
The parameter enables scene controller.
7
1
0
Switch ON level.
The parameter defines the dimming level when restored from the OFF state by push button.
8
1
1
Dimming Duration.
The parameter defines how long it takes to dim to the desired level.
Note! Only Multilevel Switch Command Class is affected by this parameter.
9
2
60
Meter Report Interval.
The parameter defines the report interval for Power Metering.
Basic V2
COMMAND_CLASS_BASIC_V2
Meter V3
COMMAND_CLASS_METER_V3
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Switch Multilevel V4
COMMAND_CLASS_SWITCH_MULTILEVEL_V4
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic V2
COMMAND_CLASS_BASIC_V2
Central Scene V3
COMMAND_CLASS_CENTRAL_SCENE_V3
Configuration V3
COMMAND_CLASS_CONFIGURATION_V3
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V4
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V3
COMMAND_CLASS_METER_V3
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Supervision
COMMAND_CLASS_SUPERVISION
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Switch Multilevel V4
COMMAND_CLASS_SWITCH_MULTILEVEL_V4
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V3
COMMAND_CLASS_VERSION_V3
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Factory Reset Procedure
By pressing and holding the main button for 20 seconds, the dimmer will perform a complete factory reset. The connected light source will blink once and go in the ”OFF” state if successfully reset.
NB! Please use this procedure only when the primary controller/gateway is missing or otherwise inoperable.
Where to find S2 DSK on product
The Z-Wave DSK can be found in the QR-Code and is located in 3 locations;
1. Box of the product.
2. On physical product, placed on the metal frame.
3. On the PCB.
Classic Exclusion
Remove
Please refer to your primary controller manual on how to enter remove mode. The device can only be removed from the network if the primary controller is in remove mode.
When the primary controller is set to remove modus press the main button on the dimmer 6 times in a rapid sequence.
When the device is removed from the network, the device will revert to factory default settings.
Controller Classic Inclusion
Add
Please refer to your primary controller manual on how to enter add mode. The device can only be added to the network if the primary controller is in add mode.
When the primary controller is set to add modus press the main button on the dimmer 6 times in a rapid sequence.
If the device already belongs to a network, follow the removing process before adding it in your network. Otherwise, the adding of this device will fail.
Other Special Features
Paragraph 8 "Power Metering" configuration guide.
Controller Classic Exclusion
Remove
Please refer to your primary controller manual on how to enter remove mode. The device can only be removed from the network if the primary controller is in remove mode.
When the primary controller is set to remove modus press the main button on the dimmer 6 times in a rapid sequence.
When the device is removed from the network, the device will revert to factory default settings.
Classic Inclusion
Add
Please refer to your primary controller manual on how to enter add mode. The device can only be added to the network if the primary controller is in add mode.
When the primary controller is set to add modus press the main button on the dimmer 6 times in a rapid sequence.
If the device already belongs to a network, follow the removing process before adding it in your network. Otherwise, the adding of this device will fail.
S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Color
If the product is only available in one color, pick the color from the list.
Electric Load Type
Select the electric load type(s) supported by the device.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Neutral Wire Required
For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.
Switch Type
Describes the type of operator for a switch.
Z-Wave Scene Type
Indicates which of the two types of Z-Wave scene command classes are supported. Scenes or Central Scene
Supported Meter Type
Indicate which type of metering is supported by the device.
Switch Load Capacity Volt-Ampere
The amount of switch load energy the product is rated for in VA (Volt-Amperes)
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps
Switch Load Capacity Watts
The amount of switch load energy the product is rated for in Watts