Teltonika Kit for metal DIN-Rail compatible RUT2xx, RUT9xx and RUTXxx

Double relay for radio on and off. It is designed to be installed in standard mechanism boxes next to a wall switch, being compatible with the existing switch and its frame.

They can also be mounted anywhere else where it is necessary to operate two independent 1.5 kW combined power devices. The Fibaro dual on / off relay can turn connected devices on or off either via radio waves or directly connected wall switches.

FIBARO smart module Z-Wave + switching micromodule
The Smart FIBARO micromodule has been designed to activate and deactivate electrical devices. Thanks to its small size, it can be installed in junction boxes or flush-mounting boxes. The module is controlled by the Z Wave network or by a simple switch. Connect your FIBARO Smart Module to your Z-Wave system and other devices to enjoy almost endless possibilities!

This module has two potential-free relays (dry contact) with a timer function (to create a pulse), so it can be used both to switch a conventional 230V voltage as well as any type of DC power supply (5V, 12V ... 24V DC). Therefore, it can be used to control any type of load such as a boiler (by connecting the dry contact instead of a thermostat) or a garage door operator ...

In addition, it has a function to avoid the simultaneous activation of the 2 relays, essential in certain applications to avoid short circuits.

Convenient Terminal Blocks - Easy Installation
The FIBARO Smart Module is equipped with increased cross section plugs that allow you to connect it to larger diameter cables and simplify the installation process.

Easy to use setup menu
The integrated RGB diode is a valuable aid during the installation process. The light will show if the FIBARO Smart Module has been added or removed from the network. You can also see if a calibration or update has been successful.

Z wave network coverage tester
Use the FIBARO Smart Module to check the signal quality on the Z-Wave network. The built-in RGB LED will help you check if the location you have selected for installation is within its range.

Software updates
You can update your FIBARO Smart Module software to the latest version once it is available. This way, you have access to the latest features without having to buy the latest version of the device.

Easy to install
Simply place the module in the back box and plug it into an existing installation. The miniature size of the module allows it to be placed in many convenient locations.

Scene management
Even the most complex actions can be activated by a wall switch connected to a module. With a simple push of the button when entering a room, it is as natural as turning on the lights. 1 to 3 presses and a long press can be assigned to four different actions

Your mobile device is your remote control
You can control the modules and receive information through your personal computers and mobile devices. The FIBARO Single Switch 2 does not require expensive control panels to function.

Caution, this module requires neutrality to function.

FUNCTIONS:

Control two lights / devices remotely
Can be installed behind an existing switch (bi-stable or monostable)
ON / OFF function
Two potential-free relays (door control, boiler, garage door, etc.)
Integrates the Z-Wave 500 series chip
250% faster communication compared to standard Onda Z devices.
Integrated scene trigger mechanism (via S2)
Classes of communication and security notification
Configuration menu with a diode
Supports safe mode (Z-Wave Network Security) encrypted with AES-128 encryption
Integrated Z-Wave network coverage tester
OTA software update (driver dependent)
Larger terminal blocks for easier wiring
Rounded shape to meet the highest standards
Small, discreet and aesthetic
Ease of use and installation

TECHNICAL DATA :

Module Type: Z Wave Receiver
Power supply: 100 - 240V ~, 50 / 60Hz or 24 - 30 Vdc
Wiring: 3 wires, neutral required (at 230V)
Maximum power:
Maximum current per output: 6A / 110 - 240V ~, 50 / 60Hz (differs depending on the type of load)
Maximum total current: 9.5A / 110 - 240V ~, 50 / 60Hz (differs depending on the type of load)
Frequency: 868.42 Mhz
Transmission distance: 50m free field, 40m indoors (depends on building structure)
Signal power: 1mW
Dimensions: 42.5mm x 38.25mm x 20.3mm (L x W x H)
Operating temperature: 0-35 ° C
Standards: EC, ROHS, 2011/65 / EU, 2014/53 / EU, 2015/863, ZWAVE PLUS
All documentation and manuals for the Fibaro product are available at manuals.fibaro.com.