Technical characteristics

Home Automation Technology	Z-Wave 700 Series
Characteristic	Dimmer

More info

Adjust the brightness to the right level with the Zooz 0-10V dimmer

Take full control of your 0-10V LED fixtures with this compact dimmer module. Program your lights to dim automatically every night. Create custom rules based on occupancy or daylight.

Automated lighting ensures the light level in your restaurant, warehouse, or office is always just right. You no longer need to remember to change the wall switch. The lights will dim automatically when needed and turn off at night. Simply program the 0-10V Dimmer on your Z-Wave hub and enjoy the freedom that smart lighting offers in any space.

Remember that you will need a compatible Z-Wave controller to use this device.

Facility

The 0-10V Dimmer is installed between your 0-10V LED driver and a wall switch. It requires a 120V power line and a neutral wire, so please ensure your wiring meets the requirements for successful installation.

The dimmer allows you to change the brightness level of the controller via Z-Wave, as well as from the wall switch if you connect it to a momentary push-button switch (DO NOT connect it to any existing wall dimmer).

You can also completely cut power to the LED driver if it's a 1-10V driver that doesn't fully turn off the light when dimming. This is possible thanks to a relay built into this smart module. Advanced settings also allow you to set minimum and maximum brightness levels, as well as the ramp speed.

Features of the Zooz ZEN54 0-10V attenuator:

Z-Wave 0-10V dimming control for LED accessories
Ideal for 0-10V LED drivers in LED panels
Smooth dimming with instant status updates
It installs behind your existing wall switch (on/off or momentary)
Z-Wave 700 series chip for improved range and faster control
Advanced settings including minimum and maximum brightness
Built-in Z-Wave signal repeater for enhanced communication

Zooz ZEN54 0-10V Dimmer Technical Specifications:

Installation: For indoor use only
Power supply: 120-240 VAC, 50/60 Hz
Maximum loads: 4 A, 960 W at 240V
Z-Wave range: Up to 90 meters line of sight
Dimensions: 3.81 cm high, 3.55 cm wide, 1.77 cm deep
Operating temperature: 0-40°C

Extended Z-Wave info

Name: 0-10V Dimmer

Manufacturer:ZOOZ

Identifier:ZEN54 LR

Z-Wave Certification Number:ZC14-23090325

Hardware Plattform:ZGM130S037HGN2 / ZGM130S037HGN1

FLiRS:NO

Role Type:Always On Slave

Short Description:Z-Wave™ Long Range low voltage dimmer for 0-10 V LED drivers.

Description:Z-Wave™ Long Range low voltage dimmer for 0-10 V LED drivers.

Group

Max Nodes

Description

1

5

2

5

3

5

4

5

Number

Size (Bytes)

Default Value

Name

Description

1

100

Restores state after power failure

10

1

0

Auto turn-on/off timer units

11

1

Enable or Disable Output control

12

1

2

External switch type

13

1

Association reports

14

1

Enable cut the power

2

1

Led indicator load status

3

1

3

Dimming speed time

4

1

Minimum dim level

5

1

99

Maximum dim level

6

1

0

Kick start level

7

1

Enable External Switch Pair

8

4

0

Auto turn-off timer

9

4

0

Auto turn-on timer

Application Status

COMMAND_CLASS_APPLICATION_STATUS

Association Group Information (AGI) V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic V2

COMMAND_CLASS_BASIC_V2

Configuration V4

COMMAND_CLASS_CONFIGURATION_V4

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta Data V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Indicator V3

COMMAND_CLASS_INDICATOR_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Multi Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multilevel Switch V4

COMMAND_CLASS_SWITCH_MULTILEVEL_V4

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security 2

COMMAND_CLASS_SECURITY_2

Supervision

COMMAND_CLASS_SUPERVISION

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Where to find S2 DSK on product

The SmartStart QR Code is located on the back of the relay, next to the Z-Wave Plus logo.

Classic Inclusion

1. ADD DEVICE to your hub: Initiate inclusion (pairing) in the app (or web interface). Check Long Range if using. Not sure how? Scan one of the QR codes below for step-by-step instructions or get in touch: www.support.getzooz.com

2. Finalize inclusion at the dimmer. Tap the Z-Wave™ button 3 times quickly if using traditional Z-Wave™ inclusion.

The LED indicator will blink green to signal communication and turn green for 2 seconds if inclusion is successful or turn red for 2 seconds if the pairing attempt fails.

Classic Exclusion

1. Bring your Z-Wave™ hub close to the device if possible

2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com)

3. Click the Z-Wave button on the relay 3 times quickly (the LED indicator will start blinking green)

4. Your hub will confirm exclusion, the LED indicator on the device will turn green for 2 seconds, and the ZEN54 will disappear from your controller''s device list.

Factory Reset Procedure

If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the relay, click the Z-Wave™ button twice and hold it for 15 seconds.

The LED indicator will flash red during the process and turn solid red for 3 seconds to confirm a successful reset.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

Neutral Wire Required

For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.

Z-Wave Scene Type

Indicates which of the two types of Z-Wave scene command classes are supported. Scenes or Central Scene

Electric Load Type

Select the electric load type(s) supported by the device.