Viewed products





Confianza Online


New Aqua-Scope Ball Valve Servo - Motor to operate ball valves View larger

Product Under Order

Aqua-Scope Ball Valve Servo - Motor to operate ball valves

AQUEBVSZWE

New

Motor / servo accessory to close and open ball valves with very easy installation and superior quality.

More details

Out of stock

416,00 €

Technical characteristics

Technology Z-Wave Plus

More info

The BVS (Ball Valve Servo) with Z-Wave is a motor to retrofit existing and installed ball valves into smart water controlling devices. The motor is powered by a 12 V external power supply.

The variable clamps allow mounting even in complex pipe installations. The patented motor coupling ensures easy installation and precise long-term operation. The device can operate in difficult environmental conditions, even submerged under water and allows to directly connect one additional local water sensor pad by cable. 

Remote control: Control your main water or gas valve remotely, when you have your Ball Valve Servo connected to a Z-Wave gateway.

Simple, Tools-Free: Just snap on and turn 2 knobs. Done in less then one minute!

Elbow proof: Can be installed on pipe elbows by adjustable clamps position.

Smart Adaptive Torque Control: Protects motor, valve and pipe for long term operation.

Outdoor Proof: IP67 rated, worked even submerged under water.

Integrated Water Detection Probe and Freeze Detection. Works Offline as well.

Features:

  • Power Supply. 12 V / 1 A external power supply (included)
  • Simple, Tools-Free: Just snap on and turn 2 knobs. Done in less then one minute!
  • Elbow proof: Can be installed on pipe elbows by adjustable clamps position
  • Smart Adaptive Torque Control: Protects motor, valve and pipe for long term operation
  • Outdoor Proof: IP67 rated, worked even submerged under water
  • Installation: Valves ½ inch to 1 ¼ inch
  • Integrated Water Detection Probe and Freeze Detection. Works Offline as well.
  • Clamp size: 64 - 124 mm adjustable
  • Max Driving Force: 6 Nm
  • Valve Control: Full open/Close, any position in between down to 1 % stepping
  • Protocol: Z-Wave 700-Series
  • Operatint temperature: - 30 °C - 80 °C

Article Dimensions (WxHxL) 145 x 130 x 60 mm
Package Dimensions (WxHxL) 236 x 179 x 114 mm
Article net weight 0.801 Kg
Article gross weight 1.147 Kg
Z-Wave Plus
Z-Wave S2
WEEE
CE
IP-Rating IP67

Extended Z-Wave info

Name: Custos Ball Valve Servo
Manufacturer:Custos
Identifier:BVSZWE
Z-Wave Certification Number:ZC12-21020179
Hardware Plattform:ZGM130
FLiRS:NO
Role Type:Always On Slave
Short Description:Custos Ball Valve Servo (BVS) is the most advance retrofit valve controller for real DIY
Description:With patented mechanic design, Custos BVS can be installed by yourself on existing valve of your water main within 20 seconds without any tool, to provide fully automated shutoff against flooding. A super strong and advance mechanic combined with smart software algorithm allows the BVS to deal with even the toughest valve without compromising the integrity of your valve over the time. Key features: 1. Hassle free bare hand install in 20 seconds 2. Outdoor proof, can be deployed on water main outside your house 3. Build-in local leak detection probe, can work standalone 4. Elbow friendly, adjustable clamp span can fit in smallest space or oversized valve up to 1.25 inches 5. Smart adaptive torque control and self calibration, real plug and play without any hassle for adjustment or calibration.

Manual download HERE.

Group
Max Nodes
Description
1
5
Lifeline Group - Device Reset Locally Notification - Basic Report - Binary Switch Report - Indicator Report - Sensor Multilevel Report – Temperature “Auto report based on Configuration Parameter 0x22 Setting.” - Heat Alarm Notification Report (0x04) - 0x00 = State idle - 0x02 = Overheat – no location support - - 0x06 = Underheat – no location support - Water Alarm Notification Report (0x05) - 0x00 = State idle - 0x02 = Water leak detected – no location support - Water Valve Notification Report (0x0F) - 0x01 = Valve operation - 0x00 = VALVE CLOSED/OFF (Valve does not let the water run through.) - 0x01 = VALVE OPEN/ON (Valve lets the water run through)
2
5
- Basic Set (By default the Configuration CC parameter 0x11 (17) “Inverse Water Valve report” is enabled to send out following report.) - 0x00 = Let the water run through (Based on Configuration Parameter 0x13) - 0xFF = Doesn’t let the water run through. (Based on Configuration Parameter 0x12) - 0x00 = Let the water run through (Based on Configuration Parameter 0x13) - 0xFF = Doesn’t let the water run through. (Based on Configuration Parameter 0x12)
3
5
- Basic Set - 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x32 Setting) - 0xFF = TRIGGERED (Based on Configuration Parameter 0x31 Setting)
4
5
- Basic Set - 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x27 Setting) - 0xFF = TRIGGERED (Based on Configuration Parameter 0x26 Setting)
5
5
- Basic Set - 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x2C Setting) - 0xFF = TRIGGERED (Based on Configuration Parameter 0x2B Setting)
Number
Size (Bytes)
Default Value
Name
Description
17
1
1
Inverse Water Valve Report
Inverses Switch Binary Report when Water Valve = 0x00 “Valve doesn’t let the water run through in Notification and real physical status.”
18
1
1
Association Group 2 SET Value
Configure Association Group 2 Basic Set value when Binary Switch Report = 0xFF *(Related to Configuration setting 0x11)
19
1
2
Association Group 2 SET Value
Configure Association Group 2 Basic Set value when Binary Switch Report = 0x00 *(Related to Configuration setting 0x11)
33
1
1
Temperature Report Unit
Configure Temperature Unit report. The default Unit is depended on Regional Frequency Setting. (By default, US=°F and EU=°C)
34
2
260
Temperature Threshold Change
Configure Temperature threshold changed and send auto report
35
2
256
Temperature Report Offset
Configure Temperature Offset degree; Higher byte 0x = Positive degree and 1x= Negative degree.
36
2
360
Overheat Trigger Value
Configure Overheat report trigger value. “Higher byte 0x00 represents Celsius °C unit, 0x01 represents Fahrenheit °F unit
37
2
342
Overheat Recover value
Configure Overheat Recover report value
38
1
0
Association Group 4 Overheat Trigger
Configure Overheat Trigger Value in Association Group 4
39
1
0
Association Group 4 Overheat Cancel
Configure Overheat Cancellation SET value
40
2
288
Freeze Trigger Value
Configure Freeze Trigger Report value
41
2
292
Freeze Recover Value
Configure Freeze Recover Report Value
42
1
1
Freeze Detection Valve Control
Enable / Disable Valve Control during Freeze when Water Leak is detected “Detected by built-in temperature sensor. Refer to Configuration CC parameter 0x28 (41) & 0x29 (42)
43
1
0
Association Group 5 Freeze Trigger
Configure Association Group 5 Freeze Detection Trigger Basic Set value
44
1
0
Association Group 5 Freeze Cancel
Configure Association Group 5 Freeze Detection Cancellation Basic Set value
49
1
1
Association Group 3 Water Leak Trigger
Configure Association Group 3 Water Leak Trigger Basic Set value
50
1
0
Association Group 3 Water Leak Cancel
Configure Association Group Water Leak Cancellation Basic Set value
51
1
1
Water Leak Detection Valve Control
Disable / Enable Valve Control when Water Leak detected
65
1
1
Buzzer
Enable / Disable Built-in Buzzer Sound
66
1
80
LED Brightness Level
Configure Built-in LED Brightness Level
67
1
0
Touch Keylock Protection
Disable / Enable Touch Keylock Protection
81
1
13
Notification Report
Configure Notification Report in Association Group 1 Lifeline “Set Bit to 0 = Disable, Set Bit to 1 = Enable” Default value 0x0D (13) Only available values as below xxxx xxx0 = Disable to report valve Open / Close status xxxx xxx1 = Enable to report valve Open / Close status (Default) xxxx xx0x = Disable Overheat Detection (Default) xxxx xx1x = Enable Overheat Detection xxxx x0xx = Disable Freeze (Underheat) Detection xxxx x1xx = Enable Freeze (Underheat) Detection (Default) xxxx 0xxx = Disable Water Leak Detection xxxx 1xxx = Enable Water Leak Detection (Default)
Application Status
COMMAND_CLASS_APPLICATION_STATUS
Association Group Information V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
Association V3
COMMAND_CLASS_ASSOCIATION_V3
Basic V2
COMMAND_CLASS_BASIC_V2
Configuration V4
COMMAND_CLASS_CONFIGURATION_V4
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V5
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
Indicator V3
COMMAND_CLASS_INDICATOR_V3
Manufacturer Specific
COMMAND_CLASS_MANUFACTURER_SPECIFIC
Multi-Channel Association V4
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V4
Notification V8
COMMAND_CLASS_NOTIFICATION_V8
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Sensor Multilevel V11
COMMAND_CLASS_SENSOR_MULTILEVEL_V11
Supervision
COMMAND_CLASS_SUPERVISION
Switch Binary V2
COMMAND_CLASS_SWITCH_BINARY_V2
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V3
COMMAND_CLASS_VERSION_V3
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Factory Reset Procedure
Factory Default Reset:

To remove Custos BVS without involve gateway in Exclusion / Remove device operation and BVS will reset all setting to Factory Default

Setting.

i. Start: Long hold Touch Sense Button for 10 seconds then short click 5 times.

ii. Processing: Yellow LED ON 1 second then wait 2-5 seconds.

iii. Success: Green LED on 2 second with long beep sounds for 2 seconds.

*Factory Default Reset will:

a. Remote the BVS from Z-Wave Network;

b. Delete the association setting;

c. Restore the configuration settings to the default.
Classic Exclusion
Remove Custos BVS from Z-Wave Network:

Set your Z-Wave Gateway into Exclusion mode / Remove device.

i. Start: Short press Touch Sense Button 3 times.

ii. Processing: Yellow LED and short beep sound keeping continue.

iii. Success: Green LED on 1 second with 2 short beep sounds.

iv. The LED indication Changes to Yellow LED blinking.
Other Special Features
None
Where to find S2 DSK on product
The DSK is printed on the product itself and also packaging label can be found outside the giftbox
Classic Inclusion
Classic Inclusion:

Set your Z-Wave Gateway into Inclusion mode / Add device.

i. Start: Short press Touch Sense Button 3 times.

ii. Processing: Yellow LED and short beep sound keeping continue. For security inclusion support, you may need to entering first 5 digit

that show on QR Code label, please refer to the instructions of central controller.

iii. Success: Green LED on 1 second with 2 short beep sounds.

iv. The LED indication changes to Green LED slow blinking from Yellow LED blinking.

S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Outdoor Use
Product is suitable for use outdoors.
Switch Type
Describes the type of operator for a switch.

 

Reviews

Write a review

Aqua-Scope Ball Valve Servo - Motor to operate ball valves

Aqua-Scope Ball Valve Servo - Motor to operate ball valves

Motor / servo accessory to close and open ball valves with very easy installation and superior quality.

10 other products in the same category: