Productos más vistos





Confianza Online


Philio PST02-1B Multisensor Z-Wave 3 en 1 (movimiento, luminosidad, temperatura) Ver más grande

Philio PST02-1B Multisensor Z-Wave 3 en 1 (movimiento, luminosidad, temperatura)

PST02-1B

Nuevo

Multisensor Z-Wave para la sensorización de presencia/movimiento, luminosidad (lumens) y temperatura ambiente

Más detalles

En Stock - Envío inmediato

38,99 €

Características técnicas

Tecnología Z-Wave Plus

Descripción

El sensor Z-Wave Plus 3 en 1 está diseñado con tres sensores de detección:

1. PIR/Moción

2. temperatura

3. Iluminación

El detector puede ser usado como un dispositivo de seguridad o de automatización del hogar. Cuando el detector coopera con los aparatos de seguridad, el detector actúa como un dispositivo de seguridad al detectar cambios en los niveles de radiación infrarroja. Si una persona se mueve dentro o a través del campo de visión de los dispositivos, se transmitirá una señal de radio de activación para provocar una condición de alarma total con el fin de ahuyentar a los intrusos. Una vez que cae la noche, el porcentaje de iluminación ambiental es inferior al valor preestablecido. Si una persona se mueve dentro o a través del campo de visión de los dispositivos, se transmitirá una señal de radio de activación para activar las luces conectadas para una mejor iluminación. Cada vez que se dispara el PIR, el sensor también enviará la temperatura y el valor de iluminación. También la temperatura enviará el valor cuando la temperatura cambie. Nota: El sensor de iluminación no funciona aún con Fibaro Homecenter 2 y Zipabox.

Cuando se incluye de forma segura, el dispositivo es capaz de aceptar comandos seguros y de enviar comandos seguros a otros dispositivos. Los comandos y el receptor de los comandos enviados con un solo clic y con doble clic del balancín pueden definirse en los parámetros de configuración y en los grupos de asociación.

Información Ampliada Z-Wave (Inglés)

Nombre: Slim Multisensor
Fabricante:Philio
Identificador:PST02-1B
Número de Certificación Z-Wave:ZC10-14080017
Plataforma Hardware:SD3502
FLiRS:NO
Tipo de Role:Reporting Sleeping Slave
Descripción Corta:Slim Multisensor 3 in 1 (PIR, Temperature and Illumination)
Descripción:The slim multisensor PST02 has PIR, temperature and illumination, 3 sensors function in one,based on Z-Wave technology.

Descargue el manual desde aquí.

Grupo
Max Nodos
Descripción
1
8
Z-Wave Plus Lifeline
2
8
Using the "Basic Set" for lighting control.
Número
Tamaño (Bytes)
Valor por Defecto
Nombre
Descripción
10
1
12
Auto Report Battery Time
The interval time for auto report the battery level. 0 means turn off auto report battery. The default value is 12. The tick time can setting by the configuration No.20.
12
1
12
Auto Report Illumination Time
The interval time for auto report the illumination. 0 means turn off auto report illumination. The default value is 12. The tick time can setting by the configuration No.20.
13
1
12
Auto Report Temperature Time
The interval time for auto report the temperature. 0 means turn off auto report temperature. The default value is 12. The tick time can setting by the configuration No.20.
2
1
255
Basic Set Level
Setting the BASIC command value to turn on the light. The 0xFF(-1) means turn on the light. For dimmer equipment 1 to 100 means the light strength. 0 means turn off the light.
20
1
30
Auto Report Tick Interval
The interval time for auto report each tick. Setting this configuration will effect configuration No.10, No.11, No.12 and No.13. Caution: Setting to 0 means turn off all auto report function.
21
1
1
Temperature Differential Report
The temperature differential to report. 0 means turn off this function. The unit is Fahrenheit. Enable this function the device will detect every minutes. And when the temperature is over 140 degree Fahrenheit, it will continue report. Enable this functionality will cause some issue please see the detail in the “Temperature Report” section.
22
1
0
Illumination Differential Report
The illumination differential to report. 0 means turn off this function. The unit is percentage. Enable this function the device will detect every minutes. Enable this functionality will cause some issue please see the detail in the “Illumination Report” section.
3
1
80
PIR Sensitivity
PIR sensitivity settings. 0 means disable the PIR motion. 1 means the lowest sensitivity, 99 means the highest sensitivity. High sensitivity means can detected long distance, but if there is more noise signal in the environment, it will re-trigger too frequency.
4
1
99
Light Threshold
Setting the illumination threshold to turn on the light. When the event triggered and the environment illumination lower then the threshold, the device will turn on the light. 0 means turn off illumination detected function. And never turn on the light. 1 means darkest. 99 means brightest. 100 means turn off illumination detected function. And always turn on the light. Notice: In none test mode, only the value in 1 to 99 will enable the illumination detected function and update the illumination value.
5
1
0
Operation Mode
Operation mode. Using bit to control. Bit0: Reserve. Bit1: 1 means test mode, 0 means normal mode. Notice: This bit only effect by the DIP Switch setting to “customer mode”, otherwise it decides by DIP Switch setting to Test or Normal Mode. Bit2: Reserve. Bit3: Setting the temperature scale. 0: Fahrenheit, 1:Celsius Bit4: Disable the illumination report after event triggered. (1:Disable, 0:Enable) Bit5: Disable the temperature report after event triggered. (1:Disable, 0:Enable) Bit6: Reserve. Bit7: Disable the back key release into test mode. (1:Disable, 0:Enable) Notice: The reserve bit is allowed any value, but no effect.
6
1
4
Mult-Sensor Function Switch
Multisensor function switch. Using bit to control. Bit0: Reserve. Bit1: Disable PIR integrate Illumination to turn ON the lighting nodes in the association group 2. (1:Disable, 0:Enable) Bit2: Reserve. Bit3: Reserve. Bit4: Reserve. Bit5: Reserve. Bit6: Reserve. Bit7: Reserve. Notice: The reserve bit is allowed any value, but no effect.
7
1
4
Customer Function
Customer function switch, using bit control. Bit0: Reserve. Bit1: Enable sending motion OFF report. (0:Disable, 1:Enable) Note: Depends on the Bit4, 0: Report Notification CC, Type: 0x07, Event: 0xFE 1: Sensor Binary Report, Type: 0x0C, Value: 0x00 Bit2: Enable PIR super sensitivity mode. (0:Disable, 1:Enable) Bit3: Reserve. Bit4: Notification Type, 0: Using Notification Report. 1: Using Sensor Binary Report. Bit5: Disable Multi CC in auto report. (1:Disable, 0:Enable) Bit6: Disable to report battery state when the device triggered. (1:Disable, 0:Enable) Bit7: Reserve. Notice: The reserve bit is allowed any value, but no effect.
8
1
3
PIR Re-Detect Interval Time
In the normal mode, after the PIR motion detected, setting the re-detect time. 8 seconds per tick, default tick is 3 (24 seconds). Setting the suitable value to prevent received the trigger signal too frequently. Also can save the battery energy. Notice: If this value bigger than the configuration setting NO. 9. There is a period after the light turned off and the PIR not start detecting.
9
1
4
Turn Off Light Time
After turn on the lighting, setting the delay time to turn off the lighting when the PIR motion is not detected. 8 seconds per tick, default tick is 4 (32 seconds). 0 means never send turn off light command.
Basic
COMMAND_CLASS_BASIC
Inclusion
There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-Wave network.
To add into a Z-Wave network:
1. Have Z-Wave Controller entered inclusion mode.
2. Pressing tamper key three times within 1.5 seconds to enter the inclusion mode.
3. After add successful, the device will wake to receive the setting command from Z-Wave Controller about 20 seconds.
Exclusion
There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-Wave network.
To remove the device from a Z-Wave network:
1. Have Z-Wave Controller entered exclusion mode.
2. Pressing tamper key three times within 1.5 seconds to enter the exclusion mode.
Node ID has been excluded.
Device Wake-Up
There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-Wave network.
Press any key once, the device will awake 10 seconds.
Factory Reset
There are two tamper keys in the device, one is in the back side, another is in the front side. Both of them can add, remove, reset or association from Z-Wave network.
To reset the device:
Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.
1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4th pressed, and the LED will light ON.
2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise, the LED will flash once.
3. IDs are excluded and all settings will reset to factory default.

 

Opiniones

Escribe tu opinión

Philio PST02-1B Multisensor Z-Wave 3 en 1 (movimiento, luminosidad, temperatura)

Philio PST02-1B Multisensor Z-Wave 3 en 1 (movimiento, luminosidad, temperatura)

Multisensor Z-Wave para la sensorización de presencia/movimiento, luminosidad (lumens) y temperatura ambiente

8 otros productos de la misma categoría:

Los clientes que compraron este producto también han comprado...