Productos más vistos





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

QUBINO DIN Dimmer para carril Z-Wave Plus

ZMNHSD1

Nuevo

Módulo regulador o dimmer Z-Wave+ QUBINO DIN Dimmer para montaje en cuadro eléctrico mediante carril DIN con medición de consumo.

Más detalles

En Stock - Envío inmediato

80,52 €

-12%

91,50 €

Características técnicas

Tecnología Z-Wave Plus
Característica Dimmer

Descripción

Qubino DIN Dimmer: Primer regulador Z-Wave para carril, verdaderamente universal

El regulador Z-Wave, Qubino DIN Dimmer es un dimmer para instalación en carril DIN para bombillas o ventiladores. Puede controlarlo de forma remota a través de la red Z-Wave o a través de interruptores de pared. 

¿Para qué se utiliza?

El Qubino DIN Dimmer es un dimmer montado en carril DIN, ideal para controlar y medir remotamente el consumo de energía de los bulbos o ventiladores. También soporta la conexión de un sensor de temperatura digital.

El dimmer de carril DIN Z-Wave más pequeño

El dimmer Z-Wave Qubino DIN Dimmer es un módulo para carril DIN que ocupa menos espacio que cualquier otro módulo para cuadro con el que se le compare de cualquier otro competidor y encajará fácilmente en menos espacio del que parece en un cuadro eléctrico con carril DIN.

Qubino din dimmer

Control energético

El dimmer Z-Wave Qubino DIN Dimmer, hace medición de consumo eléctrico del aparato eléctrico conectado y de por sí, cuando está en "standby" tan sólo consume 0.7 W.

Muy versátil

El Qubino DIN Dimmer, puede operar a través de un extenso rango de temperaturas desde los fríos -10˚C a los sofocantes 40˚C (14˚–104˚F). Soporta la conexión de un sensor de temperatura digital, que también es útil para crear escenarios complejos. Cada módulo también actúa como un repetidor con el fin de mejorar el alcance y la estabilidad de la red Z-Wave.

La instalación más sencilla

El módulo Qubino DIN Dimmer ocupa un volumen menor que los módulos comparables de cualquier otra marca y se ajusta fácilmente en cualquier carril DIN. El proceso de instalación, probado y aprobado por electricistas profesionales, resulta tan fácil y cómodo com cualquier otro modulo de carril.

Instalacion Qubino DIN Dimmer

Los módulos Z-Wave más probados y más fiables

Los módulos Z-Wave de Qubino son productos de “instalar-y-olvidarte”. Los productos Qubino que te ofrecemos, están fabricados para durar, por lo que sólo utilizan componentes electrónicos que cumplan los más exigentes niveles de calidad. Nuestros módulos además son los micromodulos Z-Wave más testeados del mercado. El Instituto Esloveno de Calidad y Medición (The Slovenian Institute of Quality and Metrology (SIQ)), una entidad europea independiente, comprueba la calidad de los parámetros reales de nuestros productos, incluyendo el aumentos de temperatura, fabricación, resistencia del aislamiento, consumo eléctrico y sobrecargas de acuerdo las normas europeas de la máxima calidad conforme a la especificación del estándar EN 60669-2-1.

Parámetros adicionales para profesionales

El módulo Qubino DIN Dimmer dispone de 17 parámetros adicionales para su uso por expertos. Algunos de los más útiles son:

  • Salida de encendido / apagado automático después del tiempo establecido
  • Cambio entre el tipo de entrada normalmente abierto y normalmente cerrado
  • Guardar el estado del dispositivo después de un corte de corriente

Este módulo Z-Wave se utiliza para controlar y regular lámparas o para controlar la velocidad de un ventilador. Puede ser controlado ya sea inalámbricamente (sin cables) por medio de la red Z-Wave o mediante un interruptor de pared conectado al mismo.
El módulo está diseñado para ser montado dentro de un armario o rack eléctrico en carril DIN. También mide el consumo de energía de las cargas conectadas. También dispone de una entrada para la conexión de un sensor de temperatura que puede ser adquirido aparte.
El Qubino DIN Dimmer también está diseñado para actuar como un repetidor para mejorar el alcance y la estabilidad de la red Z-Wave.
Por último, cabe señalar que la marca QUBINO ha establecido fuertes compromisos en la calidad y la sostenibilidad: se han seleccionado cuidadosamente los componentes de alto rendimiento. Múltiples pruebas de control de calidad también se llevaron a cabo en el módulo para garantizar la máxima durabilidad (lo suficientemente resistente para funcionar a temperaturas desde -10 °C a +40 °C).

Esquema de conexión a 220AC y a 24V DC

Esquema conexion dimmer para carril dinQubino din dimmer esquema electrico

FUNCIONES:


Controlar y regular la iluminación a distancia u otros aparatos susceptibles de regulacion
Se coloca hacia el cuadro eléctrico, instalándose en carril DIN
Permite ON / OFF / DIM
Utiliza tecnología MOSFET: compatible con lámparas halógenas de bajo voltaje con transformador electrónico, las lámparas fluorescentes compactas regulables y LED de intensidad regulable
Integra la serie de chip 500 (Z-Wave +) 
Comunicación 250% más rápido en comparación con los dispositivos estándar Z-Wave
La primera unidad de carril DIN Z-Wave del mundo
Muy bajo consumo de energía de hasta 0.7W
Temperatura de funcionamiento -10 a 40 ° C
Conector del sensor de temperatura analógico
Integra medición del consumo de energía

CARACTERÍSTICAS TÉCNICAS:

Alimentación: 110 – 230 VAC ± 10%
50 / 60 Hz, (24–30 VDC)

Carga máxima de salida AC (carga resistiva)*

0.85 A / 230 VAC
Carga máxima de salida DC (carga resistiva)* 0.85 A / 30 VDC
Output circuit power of AC output (resistive load): 200 W (230 VAC)
Output circuit power of DC output (resistive load): 21 W (24 VDC)
Precisión de la medición de potencia: +/- 2 W
Rango del sensor digital de temperatura: -50° ~ +125°C, resolucion 0.1°C
Longitud del cable del sensor digital de temperatura: 1000 mm
Temperatura de Operacion: -10° ~ +40°C
Distancia hasta 30 m en interior (dependiendo de materiales)
Dimensiones (WxHxD) 18 x 93 x 58 mm
(packaging) (21 x 95 x 64 mm)
Peso (incluyendo packaging) 50 g (56 g)
Consumo electrico en standby 0.7 W
Montaje DIN rail
Conmutación mediante: MOSFET (trailing edge)



Cumple Certificaciones  CE y ROHS

Descargar

Qubino_DIN-Dimmer-manual_V11

Qubino DIN Dimmer Manual del Usuario V1.1 en ingles

Descargar (468.96k)

Información Ampliada Z-Wave (Inglés)

Nombre: DIN Dimmer
Fabricante:QUBINO
Identificador:ZMNHSD1
Número de Certificación Z-Wave:ZC10-17035480
Plataforma Hardware:ZM5202
FLiRS:NO
Tipo de Role:Always On Slave
Descripción Corta:DIN Dimmer is a DIN rail mounted dimmer for light bulbs. You can control it either remotely through the Z-Wave network or through wall switches. It also measures power consumption and supports the connection of a digital temperature sensor.
Descripción:DIN Dimmer is a DIN rail mounted dimmer for light bulbs. You can control it either remotely through the Z-Wave network or through wall switches. It also measures power consumption and supports the connection of a digital temperature sensor.

Descargue el manual desde aquí.

Grupo
Max Nodos
Descripción
1
1
Lifeline group (reserved for communication with the main controller)
2
16
Basic on/off (triggered at change of the input I1 state and reflecting its state)
3
16
Start level change/stop level change (triggered at change of the input I1 state and reflecting its state)
4
16
Multilevel set (triggered at changes of state/value of the DIN Dimmer)
5
16
Multilevel sensor report (triggered at change of temperature sensor)
Número
Tamaño (Bytes)
Valor por Defecto
Nombre
Descripción
1
1
0
Input switch type
Available configuration parameters (data type is 1 Byte DEC): • default value 0 • 0 - mono-stable switch type (push button) • 1 - bi-stable switch type
10
2
255
Activate / deactivate functions ALL ON / ALL OFF
DIN Dimmer module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.
11
2
0
Automatic turning off output after set time
Turns off the output after set time.
110
2
32536
Temperature sensor offset settings
Set value is added or subtracted to actual measured value by sensor. Available configuration parameters (data type is 2 Byte DEC): • default value = 32536 • 32536 = offset is 0.0C • 1 - 100 = value from 0.1 °C to 10.0 °C is added to actual measured temperature. • 1001 - 1100 = value from -0.1 °C to -10.0 °C is subtracted to actual measured temperature.
12
2
0
Automatic turning on output after set time
Turns on the output after set time.
120
1
5
Digital temperature sensor reporting
Digital temperature sensor reporting If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter. Available configuration parameters (data type is 1 Byte DEC): • default value 5 = 0,5°C change • 0 = reporting disabled • 1- 127 = 0,1°C - 12,7°C, step is 0,1°C
21
1
0
Enable/Disable Double click function
If Double click function is enabled, a fast double click on the push button will set dimming power at maximum dimming value.
30
1
0
Saving the state of the device after a power failure
Based on the parameter settings the stores/does not store the last value of the output after power failure.
40
1
5
Power reporting in Watts on power change
Set value means percentage, set value from 0 - 100=0% - 100%. Power report is send (push) only when actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%. NOTE: if power changed is less than 1W, the report is not send (pushed), independent of percentage set.
42
2
0
Power reporting in Watts by time interval
Set value means time interval (0 – 32767) in seconds, when power report is send. Reporting enabled. Power report is send with time interval set by entered value. Please note, that too fast reporting can cause too much Z-Wave traffic resulting in Z-Wave poor response.
5
1
0
Working mode
With this parameter is possible to change the module presentation on the user interface NOTE: After parameter change, first exclude module (without setting parameters to default value) then wait at least 30s and then re include the module!
60
1
1
Minimum dimming value
The minimum level may not be higher than the maximum level! 1% min. dimming value is defined by Z-Wave multilevel device class. When the switch type is selected as Bi-stable, it is not possible to dim the value between min and max. If Switch_multilevel_set is set to the value “0”, the output is turned OFF. If Switch_multilevel_set is set to the value “1”, the output is set to the minimum diming value.
61
1
99
Maximum dimming value
The maximum level may not be lower than the minimum level! 99% max. dimming value is defined by Z-Wave multilevel device class. When the switch type is selected as Bi-stable, it is not possible to dim the value between min and max.
65
2
100
Dimming time (soft on/off)
Set value means time of moving the DIN Dimmer between min. and max. dimming values by short press of push button I or controlled through UI (BasicSet).
66
2
3
Dimming time when key pressed
Time of moving the DIN Dimmer between min. and max dimming values by continues hold of push button I or associated device.
67
1
0
Ignore start level
This parameter is used with association group 3.A receiving device SHOULD respect the start level if the Ignore Start Level bit is 0. A receiving device MUST ignore the start level if the Ignore Start Level bit is 1.
68
1
0
Dimming duration
This parameter is used with association group 3. The Duration field MUST specify the time that the transition should take from the current value to the new target value. A supporting device SHOULD respect the specified Duration value.
Basic
COMMAND_CLASS_BASIC
Switch Multilevel V3
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Association Group Information V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V4
COMMAND_CLASS_METER_V4
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Sensor Multilevel V7
COMMAND_CLASS_SENSOR_MULTILEVEL_V7
Switch All
COMMAND_CLASS_SWITCH_ALL
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Switch Multilevel V3
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Exclusion
• Connect module to power supply

• bring module within maximum 1 meter (3 feet) of the main controller,

• enable add/remove mode on main controller,

• press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or

• press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second.

By this function all parameters of the module are set to default values and own ID is deleted.

If push button I1 is pressed three times within 3s (or service button S is pressed more than 2 and less than 6 seconds) module is excluded, but configuration parameters are not set to default values.



NOTE 1: If the module is included with parameter 1 value 3, 4 or 5 and module reset is done, wait at least 30s before next inclusion.



NOTE 2: Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Inclusion
• Connect module to power supply (with

temperature sensor connected - if purchased),

• enable add/remove mode on main controller

• auto-inclusion (works for about 5 seconds after connected to power supply) or

• press service button S for more than 2 second or

• press push button I1 three times within 3s (3 times change switch state within 3 seconds).



NOTE1: For auto-inclusion procedure, first set main controller into inclusion mode and then connect module to power supply.

NOTE2: When connecting temperature sensor to module that has already been included, you have to exclude module first. Switch off power supply, connect the sensor and re-include the module.

Factory Reset
• Press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or

• press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second.



Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Switch Type
Describes the type of operator for a switch.
Color
If the product is only available in one color, pick the color from the list.
Sensors
Sensor types supported by the product.

 

Opiniones

Escribe tu opinión

QUBINO DIN Dimmer para carril Z-Wave Plus

QUBINO DIN Dimmer para carril Z-Wave Plus

Módulo regulador o dimmer Z-Wave+ QUBINO DIN Dimmer para montaje en cuadro eléctrico mediante carril DIN con medición de consumo.

Accesorios, complementos y/o alternativas

30 otros productos de la misma categoría:

Los clientes que compraron este producto también han comprado...