Produtos visualizados





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

MCO Home MH7 - Termostato para aquecimento de água quente (Version 2)

MCOEMH7H-WH2

Novo

Z-Wave mais termostato para aquecimento com base em água quente, como sistemas de caldeira a gás , válvula ou bomba de água, aquecimento por piso radiante de água quente, sistemas de radiadores, etc.

Mais detalhes

Em estoque

127,05 €

Características tecnicas

Tecnologia Z-Wave Plus

Mais Informação

O termostato de aquecimento de água MCOHome é um dispositivo para controle interno de temperatura com tecnologia Z-Wave Plus. O MCO Home MH7-WH-EU é usado principalmente para controlar caldeiras montadas na parede, quer gasóleo ou caldeiras a gás para água com válvulas / bombas, etc., enquanto a variante ou modelo MCO Home MH7 -EH-EU é indicado para sistemas de aquecimento elétrico. O dispositivo é de alta confiabilidade e praticidade. E pode ser incluído e operado em qualquer rede Z-Wave com outros dispositivos certificados Z-Wave de qualquer outro fabricante.
Insistimos na eficiência oferecida por este Z-Wave e termostato para aquecimento com base em água quente, como sistemas de caldeira a gás, válvula ou bomba de água, aquecimento por piso radiante de água quente, sistemas de radiadores, etc.

Este termostato Z-Wave é construído com um painel de vidro temperado com botões capacitivos
Programação programável: 4 eventos todos os dias de 7 dias 5 + 2 5 + 1 + 1
Operação: manual, automático (períodos de tempo), feriados (economia de energia)
Com dois sensores de temperatura para o controle interno de temperatura. Sensor: NTC 15K
Temp externo Sensor (opcional): NTC R25 = 15K e Omega B25 / 50 = 3550K
Ambiente de trabalho: 0-50 <90% RH (sem condensação)
Built-in Z-Wave module (UE) Opcional: RS485, WIFI
MH7-WH-EU

Informação alargada da Z-Wave (Inglês)

Nome: Heating Thermostat
Fabricante:MCO Home
Identificador:MH7H-WH/EH
Número de Certificação Z-Wave :ZC10-18046084
Plataforma de Hardware :ZM5202
FLiRS:Não
Tipo de Role :Always On Slave
Descrição breve :MCOHome Water / Electrical Heating Thermostat MH7H is a Z-Wave Plus enabled device for indoor temperature control.
Descrição : MH7H-WH is mainly applied to control wall mounted boiler, water valve/pump etc. , while MH7H-EH is for electrical heating system.The device is of high reliability and practicability, which can be included and operated in any Z-Wave network with other Z-Wave certified devices from any other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. Features:  Capacitive touch buttons  Tempered glass panel, PC alloy enclosure  Precise temperature calibration function  Attractive appearance  Clear display, easy to operate Specification:  Power Supply:AC85-260V, 50/60HZ  Output: MH7H-WH ≤5A ; MH7H-EH≤ 16A  Self Consumption:≤1W  External Temp. Sensor(optional): NTC R25℃=15KΩ B25℃/50℃=3550K  Working Environment:0-50℃; 0-90% RH(Non- condensation)  Temperature Setting:5-37 ℃(41-99℉)(Adjustable)  Dimension:86* 86*15mm  Hole Pitch:60-61mm

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
5
Z-Wave Plus Lifeline
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Firmware Update Meta-Data V4
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S2
COMMAND_CLASS_SECURITY_2
Sensor Multilevel V5
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
Supervision
COMMAND_CLASS_SUPERVISION
Thermostat Mode V2
COMMAND_CLASS_THERMOSTAT_MODE_V2
Thermostat Operating State
COMMAND_CLASS_THERMOSTAT_OPERATING_STATE
Thermostat Setpoint V2
COMMAND_CLASS_THERMOSTAT_SETPOINT_V2
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Inclusion
In normal working interface, press & hold S4 to enter interface for adding or removing of Z-Wave network. Before device added into network, “- - -” will display on the screen. Then press S4 once, device will enter learning mode to get a node ID. If adding is succeed, a node ID will display on the screen in a few seconds.



A node ID can always inform us whether the device is in the network or not.



After adding, turn off the device and then turn it on. Now the device is ready to be operated by controller/ gateway in Z-Wave network.

Exclusion
In normal working interface, press & hold S4 to enter interface for adding or removing of Z-Wave network. Before device removed from network, a Node ID will display on the screen. Then press S4 once. If removing is succeed, “- - -”will display on the screen in a few seconds.



A node ID can always inform us whether the device is in the network or not.When removed, the device will restore its factory setting.

Factory Reset
A parameter P18 in the secret menu can be used to restore factory setting locally. Please use this procedure only when the network primary controller is missing or otherwise inoperable. ; And a parameter FF can be used to restore the factory setting via Z-Wave.
S2 Unauthenticated
S2_UNAUTHENTICATED
Thermostat HVAC Systems Supported
Indicate which HVAC system or systems are supported by the thermostat.
Thermostat Modes
Select the mode(s) supported by the thermostat.
Thermostat Power Source
Select one or more supported power sources for a thermostat.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps
Neutral Wire Required
For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.
Sensors
Sensor types supported by the product.

 

Avaliações

Nota 
2020-01-21

Muy bien el termostato

Me llegó rapido. Encaja perfecto en caja de mecanismos. Va bien con mi Saunier Duval.

Faça uma avaliação!

Escrever uma avaliação

MCO Home MH7 - Termostato  para aquecimento de água quente  (Version 2)

MCO Home MH7 - Termostato para aquecimento de água quente (Version 2)

Z-Wave mais termostato para aquecimento com base em água quente, como sistemas de caldeira a gás , válvula ou bomba de água, aquecimento por piso radiante de água quente, sistemas de radiadores, etc.

29 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: