Produtos visualizados





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

HANK Lâmpada LED RGB tecnologia Z-Wave Plus

HNKERGB01

Novo

A lâmpada LED Z-Wave RGB para tomada convencional E27 (a tampa "gorda") de toda a vida.

Mais detalhes

Não disponível

35,70 €

-15%

42,00 €

Características tecnicas

Tecnologia Z-Wave Plus

Mais Informação

Trazer cor à sua vida e criar uma atmosfera confortável pessoal com tons brancos e coloridos regulável. A lâmpada LED RGB Hank se encaixa em cada porta-lâmpada E27 e pode ser conectada a um centro doméstico inteligente através da tecnologia sem fio Z-Wave logo após o aparafusamento. O chip de rádio necessário já está integrado no alojamento do bulbo. Através do controle remoto, smartphone ou tablet, você pode variar o brilho e a cor da luz também. Luz do dia, luz de velas ou clima de festa: A partir de agora, você pode definir uma atmosfera de luz de acordo com seus desejos ou usar cenas (por exemplo, no caso de um alarme) ativando a cor da luz apropriada.

Como uma função especial, a cor da lâmpada Hank pode ser ajustada completamente sem usar uma aplicação de smartphone. Controlá-lo apenas pelo interruptor de parede existente. Através da combinação ON / OFF no interruptor de parede, a lâmpada entra no modo de desvanecimento e é reduzida através de todas as cores principais. Depois de ter encontrado a cor que você gosta, selecione-o ligando / desligando a lâmpada novamente. Em seguida, o modo de atenuação será interrompido e a lâmpada permanecerá no modo de cor atual.

Devido à tecnologia LED, o consumo de energia é muito baixo em comparação com as lâmpadas convencionais. A lâmpada de Hank é tão brilhante quanto uma lâmpada convencional de 60W, mas precisa apenas de 7W.

Características:

Lâmpada para capa tipo E27
Chip de rádio integrado
Cores: RGB de 3 canais, 16 milhões de cores, branco quente e frio
Consumo de energia: máx. 7 W
Intensidade da luz: 600 lm
Classe de eficiência energética: A +
Tecnologia sem fio: Z-Wave Plus
Dimensões: 115x65x65 mm

Informação alargada da Z-Wave (Inglês)

Nome: RGB Bulb
Fabricante:Hank
Identificador:HKZW-RGB01
Número de Certificação Z-Wave :ZC10-16095231
Plataforma de Hardware :ZM5101
FLiRS:Não
Tipo de Role :Always On Slave
Descrição breve :RGB Bulb is a smart bulb enables Z-Wave remote command and control (on/off/dim). It has over 16,000,000 colors, you can choose its color according to your favour.
Descrição :RGB Bulb is a smart bulb enables Z-Wave remote command and control (on/off/dim). It has over 16,000,000 colors, you can choose its color according to your favour.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
5
Z-Wave Plus Lifeline RGB BULB supports only one association groupings: RGB BULB will send the follow notification to the associated nodes when the status of the RGB BULB is changed. 1. Set Configuration parameter 24 to 0: Reserved 2. Set Configuration parameter 24 to 1: Send Basic Report 3. Set Configuration parameter 24 to 2: Send Basic Report only when the status of the RGB BULB is not changed by Z-WAVE Command.
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
21
1
0
Setting device status after power failure
Define how the RGB BULB will react after the power supply is back on.
24
1
1
Notification when Load status change
RGB BULB can send notifications to associated device (Group Lifeline) when the status of the RGB BULB is changed.
255
4
0
Reset to factory default
RGB BULB will exclude from the Z-Wave network with this particular command.
Exclusion
To remove the RGB BULB from the Z-Wave network:

(1) Screw in the RGB BULB.

(2) Set the Z-Wave network main controller into excluding mode

(see Z-Wave controller operating manual).

(3) Toggle the wall switch off and on 3 times quickly(within 3

and the final ending position of the wall switch must be on),

if the exclusion is successful, the RGB BULB will blink fast in

orange for less than 5 seconds and then keep on for 3 seconds.

RGB BULB will keep on warm white after the exclusion procedure

is finished.
Factory Reset
There are two ways to reset the RGB BULB. One is that removing

RGB BULB from the Z-Wave network, the other is that using the

configuration command class.
Inclusion
To include RGB BULB into a Z-Wave network as a non-security device:

(1) Make sure the power supply is disconnected and the RGB BULB is

located within a direct Z-Wave network's main controller

communication range.

(2) Set the Z-Wave network main controller into learning mode

(see Z-Wave network controller operating manual).

(3) Insert the RGB BULB into a lamp-socket and then power on.

(4) Auto-inclusion will be activated. If the inclusion is successful, the

RGB BULB will blink fast in blue for less than 5 seconds and then

keep on for 3 seconds. RGB BULB will keep on in the color before it

is included into the Z-Wave network after the inclusion procedure

is finished.



To include RGB BULB into a Z-Wave network as a security device:

(1) Screw in the RGB BULB.

(2) Set the Z-Wave network main controller into learning mode

(see Z-Wave network controller operating manual).

(3) Toggle the wall switch off and on 3 times quickly (within 3 seconds

and the final ending position of the wall switch must be on).

(4) If the inclusion is successful, the RGB BULB will blink fast in green

for less than 5 seconds and then keep on 3 seconds. RGB BULB will

keep on in the color before it is included into the Z-Wave network

after the inclusion procedure is finished.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

 

Avaliações

Nota 
2020-07-13

Bombilla económica

Económica y práctica. Muy útil para avisarte del disparo de una escena o para avisarte de si algo ocurre

Faça uma avaliação!

Escrever uma avaliação

HANK Lâmpada LED RGB tecnologia Z-Wave Plus

HANK Lâmpada LED RGB tecnologia Z-Wave Plus

A lâmpada LED Z-Wave RGB para tomada convencional E27 (a tampa "gorda") de toda a vida.

4 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: