Produtos visualizados





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

Sensor de Água Aeotec 7 (Série 700) Sensor de Inundação Z-Wave+ ver2

AEOEZWA018

Novo

O Water Sensor 7 é um sensor projetado para detectar pingos e vazamentos e ajudar a mitigar os danos causados pela água.

Mais detalhes

Em estoque

42,00 €

Características tecnicas

Tecnologia Z-Wave Serie 700

Mais Informação

O detector de inundação, Aeotec Water Sensor 7 é um sensor de inundação, um sensor de vazamento e um sensor de segurança em um dispositivo.

Detecção de vazamento. Vazamentos são a base para contas caras e danos quando aparecem onde não deveriam. Monitorando mais do que apenas a presença de líquido, o Aeotec Water Sensor 7 Pro faz jus ao seu nome ao monitorar a ausência de água. Quando usado para monitorar tanques ou poços, o Aeotec Water Sensor 7 Pro pode alertá-lo quando os níveis de água estão muito baixos e acionar rotinas de automação.

O Aeotec Water Sensor 7 Pro não apenas monitora vazamentos de água. Uma vez conectado ao seu sistema de automação Z-Wave, o Aeotec Water Sensor 7 Pro pode tomar medidas de proteção para ajudar a limitar a quantidade de danos causados por gotejamento, vazamentos, quebras ou outros fluxos de água. Por exemplo, no caso de uma ruptura de tubulação, o dispositivo inteligente pode comandar válvulas de água inteligentes, incluindo aquelas instaladas na tubulação principal, para fechar automaticamente.

Gerenciamento de aquecimento. O Aeotec Water Sensor 7 Pro monitora a temperatura ambiente para controlar e gerenciar sistemas de aquecimento ou resfriamento conectados.

Gestão da qualidade do ar. Além de controlar a temperatura ambiente, o Aeotec Water Sensor 7 Pro mede a umidade relativa do ambiente. Com monitoramento de umidade em tempo real, o dispositivo inteligente pode ser usado para gerenciar automaticamente a qualidade do ar em uma sala, ativando exaustores e umidificadores ou desumidificadores.

Destaques do recurso:

Sonda de sensor para detecção de vazamentos em áreas de difícil acesso

SEM CONTROLE DE TEMPERATURA OU UMIDADE
Até 5 anos de vida útil da bateria
Compatível com Aeotec Smart Home Hub
Tecnologia Gen7 (série Z-Wave 700)
SmartStart
Z-Wave Plus V2
Alimentação: bateria de lítio CR123A

Informação alargada da Z-Wave (Inglês)

Nome: Water Sensor 7 Pro
Fabricante:Aeotec
Identificador:ZWA019-C
Número de Certificação Z-Wave :ZC12-20060068
Plataforma de Hardware :ZGM130
FLiRS:Não
Tipo de Role :Reporting Sleeping Slave
Descrição breve :The Aeotec Water Sensor 7 Pro detects any liquid, which is spreaded by a leakage or other damage. It also measures the humidity and temperature of its environment.
Descrição :The Water Sensor 7 pro brings more safety into your home. With its flexible sensor probe and the sensitive sensor point it detects the presence and absence of water at any given location. Furthermore the Watersensor 7 pro is enabled to accurately measure the temperature and humidity of its environment, so you are always informed about your room climate. Thanks to the latest Z-Wave 700 series technology, the Water Sensor 7 is distinguished with and increased range, S2 Security, OTA FW update and SmartStart.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
5
Lifeline association to gateways
2
5
Control devices when water leakage is detected
3
5
Sends out alarm message when water leakage is detected
4
5
Sends out alarm messages when tamper is tripped
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
10
2
0
Time Delay of "Off" command frame
Off command is sent after a delay defined in this parameter.
11
2
0
Delay of Tamper Alarm Cancellation
Time a tamper alarm is delayed.
12
1
1
Reporting Tamper Alarm Cancellation
This parameter defines if the alarm cancellation event is reported.
16
1
20
Minimum Temperature change to report
This value defines the minimum change of temperature to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the temperature changes. However, periodic reports, managed by configuration parameter 18, may still be active.
17
1
5
Minimum humidity change to report
This value defines the minimum change of humidity to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the humidity changes. However, periodic reports, managed by configuration parameter 18, may still be active.
18
2
43200
Temperature and Humidity Periodic Reports
This parameter defines the time interval to send an unsolicited report. If the value is set to 0, there will be no periodic reports sent to the controller. However, reports on temperature/humidity changes, managed by configuration parameters 16 and 17, may still be active.
255
4
0
Reset Parameter
This parameter helps reset configuration parameters and the device to factory defaults 1 - 1431655764 (0x55555554) - Reset all Parameter settings to their default settings. 1431655765 - Completely factory reset sensor and send device reset locally notification.
3
1
7
Visual LED Indications
This parameter defines when LEDs will indicate events. Disabling all indications may extend battery life. Value 0 means - No Indications.
4
1
0
Range Test after double click
Allows to enable the activation of a Z-Wave range test with double clicking the tamper switch.
5
1
0
2nd Association Group Trigger
This parameter defines the status of the magnet switch that causes sending a BASIC command to all devices of Association Group 2.
6
1
2
Command Sent to Devices of Association Group 2
This parameter defines which commands is sent to 2nd Association Group
7
1
255
BASIC command "On event" value
This is the BASIC command value sent in case of "On" event.
8
1
0
BASIC command "Off event" value
This is the BASIC command value sent in case of "Off" event.
9
2
0
Time Delay of "On" command frame
On command is sent after a delay defined in this parameter.
Association Group Information V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Battery
COMMAND_CLASS_BATTERY
Configuration V4
COMMAND_CLASS_CONFIGURATION_V4
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V5
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
Indicator V3
COMMAND_CLASS_INDICATOR_V3
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Notification V8
COMMAND_CLASS_NOTIFICATION_V8
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S2
COMMAND_CLASS_SECURITY_2
Sensor Multilevel V11
COMMAND_CLASS_SENSOR_MULTILEVEL_V11
Supervision
COMMAND_CLASS_SUPERVISION
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V3
COMMAND_CLASS_VERSION_V3
Wake Up V2
COMMAND_CLASS_WAKE_UP_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Where to find S2 DSK on product
Scan the QR code inside the battery compartment of the device and your controller will add the device automatically when powered up.
Classic Inclusion
Inclusion

1. Open the housing.

2. Remove the battery protection.

3. Press the tamper on the side of the appliance three times quickly.
Classic Exclusion
Exclusion

1. Open the housing.

2. Press the tamper on the side of the appliance three times quickly.
Wake-Up Procedure
The Node Information Frame (NIF) is the business card of a Z-Wave device. It contains information about the device type and the technical capabilities. The inclusion and exclusion of the device is confirmed by sending out a Node Information Frame. Beside this it may be needed for certain network operations to send out a Node Information Frame. To issue a NIF execute the following action: Press the tamper once
Factory Reset Procedure
Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Once Cover is removed and the tamper switch is tripped, push the tamper for 5 seconds until the RED LED blinks once. Then release tamper and push it again for 5 seconds while the RED LED is blinking until the GREEN LED blinks once.
Other Special Features
- The product is able to perform a range test to the gateway by setting parameter 4 as described in the manual
S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.
Color
If the product is only available in one color, pick the color from the list.
Battery Quantity
Enter the number of batteries of the designated type that the product uses.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

 

Avaliações

Escrever uma avaliação

Sensor de Água Aeotec 7 (Série 700) Sensor de Inundação Z-Wave+ ver2

Sensor de Água Aeotec 7 (Série 700) Sensor de Inundação Z-Wave+ ver2

O Water Sensor 7 é um sensor projetado para detectar pingos e vazamentos e ajudar a mitigar os danos causados pela água.

8 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: