Nome: Z-Wave Metering Plug Smart Start
Fabricante:Popp & Co.
Número de Certificação Z-Wave :ZC10-18026015
Plataforma de Hardware :ZM5101
Tipo de Role :Always On Slave
Descrição breve :The IP 44Wall Plug Switch Outdoor can be placed between a wall outlet for Schuko plugs and electric devices, plugged in by cord.
Descrição :The Wall Plug Switch Outdoor can be placed between a wall outlet for Schuko plugs (plug type F) and electric devices, plugged in by cord. It can switch all loads up to 3500 W. The plug switch is IP 44 rated and can therefore be used both in dry as well as humid environments in- and outdoor.
Switching is controlled by the local button or wirelessly. The use of the local button and the behavior oon wireless commands can be configured using configuration parameters. Whn detached from the control of local leads the button on the device can be used to trigger scenes in a central gateway. Single click and double click are distinguished.
The device is also measuring the mains voltage supply reporting mains voltage and mains frequency. Addtionally the powr consumption of the attached load is monitored as well.
All metering values an be requested from the central controller and will be reported unsolicited if configured.
Descarregue o manual a partir de aqui.
Control other devices on single click of the button. BASIC command (on/off) is sent according to switching state of the load.
Valor por defeito
LED Operation Mode
Defines when the LED shall shine and how
Defines if and after which time the device shall turn off without any user interaction
LED Color on OFF state
Defines the behavior of the LED when the load is switched off
LED Color on ON state
Defines the behavior of the LED when the load is switched on
Voltage Report Threshold
Report the voltage when the voltage has changed by more then X * 1 V. When disabled the device will report every 10 minutes regardless of current voltage.
Current Reporting Threshold
Report the current when the current has changed by more then X *0,01 A. When disabled the device will report every 10 minutes regardless of current change.
Power Reporting Threshold
Report the power when the power has changed by more then X Watt. When disabled the device will report every 10 minutes regardless of power consumption change.
Soft Circuit Breaker Threshold
When the power draw exceeds the value set in this parameter for a time set in parameter 28 the soft ciruit breaker will disconnect the load.
Soft Circuit Breaker Recovery Time
Once the soft circuit breaker tipps and the load is disconnected the load will be automatically reconneced after X seconds. When disabled the load must be repowered manually or with wireless command.
Soft Circuit Breaker Delay Time
This delay time defines how fast the soft circuit breaker wil react when the threshold power is exceeded. The power is cut off only if the power draw remains over the threshold level for the defines time.
Switching behavior when receiving wireless OFF
This parameter defines if the local button shall control (switch) the load or it is only used to send out scene control commands to the central controller.
Status after Power Failure
Defines the switching status after a power failure or unplugging
Association Group Info
Central Scene V3
Device Reset Locally
Firmware Update Meta-Data V4
Manufacturer Specific V2
Multi-Channel Association V3
Sensor Multilevel V8
Transport Service V2
Z-Wave Plus Info V2
This device allows reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable. Push and hold the button for 10 seconds. After 5 seconds the LED on the button will blink fast.
Tripple Click the button
Tripple Click the button
Sensor types supported by the product.
Electric Load Type
Select the electric load type(s) supported by the device.
Product is suitable for use outdoors.
Switch Load Capacity Watts
The amount of switch load energy the product is rated for in Watts
Supported Meter Type
Indicate which type of metering is supported by the device.
IP (Ingress Protection) Rated
Product is suitable for Outdoor use and is waterproof under an IP (Ingress Protection) rating system.
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
If the product is only available in one color, pick the color from the list.