Produtos visualizados





Confianza Online


Heat-it ZTRM2fx Termostato Z-Wave empotrable para suelo radiante electrico View larger

Produto a Pedido

Heatit ZTRM2fx Recesso Z-Wave termostato para piso radiante elétrico

HEAE5430555

Novo

Heatit Z-TRM2fx é um termostato eletrônico para aquecimento de piso

Mais detalhes

Não disponível

129,99 €

Características tecnicas

Tecnologia Z-Wave Plus

Mais Informação

Heatit Z-TRM2fx é um termostato eletrônico para piso radiante. O termostato possui um chip Z-Wave integrado que pode ser conectado a sistemas de automação residencial como Fibaro, Smarthings, Homeseer, Vera, Zipato, etc.

O Heatit Z-TRM2fx é equipado com um interruptor de polo único e é compatível com a maioria das estruturas do System 55 (Elko RS16, Schneider Exxact, Gira, Jung, etc.). O termostato pode suportar uma carga máxima de 13A / 2900W a 230V. Em cargas maiores, o termostato deve controlar um contator. O termostato pode ser conectado a dois sensores externos com fio.

O termostato tem capacidade para até 5 associações (relés, tomadas de parede, etc.).

O termostato é projetado para aquecimento elétrico. Também pode ser utilizado para aquecimento de pavimentos à base de água quando ligado a Heatit Z-Water.

Características:

Sensor de piso
Sensor externo da sala
Limitador de temperatura
Programa semanal / rebobinar via gateway ou cabo piloto
Medição de potência
Pode ser usado em conexão com diferentes sensores NTC
Bloqueio infantil / modo de bloqueio
Calibração
até 5 associações
Orçamento:

Z-Wave Plus
Tensão nominal: 230V 50 / 60Hz
Carga máxima: 2900W (carga resistiva)
Cabo de aquecimento autolimitado de 750W.
Corrente máxima: 13A
Consumo de energia: <2.0W
Temperatura operacional mínima / máxima: 5 ° C - 40 ° C
Faixas de temperatura Sensor de piso: 5 ° C - 40 ° C
Sensor de ambiente externo: 5 ° C - 40 ° C
Histerese 0,3 ° C - 3,0 ° C (valor padrão 0,5 ° C)
Interruptor monopolar comutável
Compatível com sensores NTC com valores 10, 12, 15, 22, 33 e 47 k © a 25 ° C
Incluído no pacote do sensor de piso

Informação alargada da Z-Wave (Inglês)

Nome: Heatit Z-TRM2fx
Fabricante:HEATIT
Identificador:Z-TRM2fx
Número de Certificação Z-Wave :ZC10-18116305
Plataforma de Hardware :ZM5101
FLiRS:Não
Tipo de Role :Always On Slave
Descrição breve :Heatit Z-TRM2fx is an electronic thermostat for electrical floor heating. The thermostat has a built-in Z-Wave chip that can be connected with Home Automation systems like Fibaro, Futurehome, Smarthings, Homeseer, Zipato etc.
Descrição :Heatit Z-TRM2fx is equipped with a single pole switch and it fits most System 55 frames (Elko RS16, Schneider Exxact, Gira, Jung etc.). The thermostat can withstand a load of max 13A /2900W at 230V. At higher loads the thermostat must control a contactor. The thermostat may be connected to two wired external sensors. The thermostat has the capacity of up to 8 associations (relays, wall plugs etc.). The thermostat is designed for electrical heating. FEATURES Floor sensor External room sensor Temperature limiter Weekly program/setback via gateway or pilot wire Multilevel sensor command class Firmware updates (OTA) Power metering LED-diode Can be used in connection with different NTC-sensors Lock mode/child lock Calibration 8 associations Supports encryption mode: S0, S2 Authenticated Class, S2 Unauthenticated Class

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
8
Association Groups (Multi Channel support): THERMOSTAT DEVICE 1 THE MAIN THERMOSTAT DEVICE Group 1 Lifeline. (Normally used by the Z-Wave Controller) Sends: - Device Reset Notifications. - Thermostat Setpoint Reports - Thermostat Mode Reports - Basic Reports - Meter Reports Max. nodes in group: 8
2
8
Association Groups (Multi Channel support): MULTILEVEL SENSOR DEVICE 2 DEVICE FOR EXTERNAL ROOM TEMPERATURE SENSOR Group 1 Lifeline Max. nodes in group: 8 Group 2 Send Multilevel Sensor Reports. Max. nodes in group: 8
3
8
Association Groups (Multi Channel support): MULTILEVEL SENSOR DEVICE 3 DEVICE FOR FLOOR SENSOR Group 1 Lifeline Max. nodes in group: 8 Group 2 Send Multilevel Sensor Reports. Max. nodes in group: 8
4
8
Association Groups (Multi Channel support): BINARY SWITCH DEVICE 4 DEVICE FOR THE INTERNAL RELAY Group 1 Lifeline Max. nodes in group: 8 Group 2 Send Binary Switch Set commands representing the status of the internal relay. Max. nodes in group: 8
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
1
1
0
Operation Mode
0 Off. (Default) 1 Heating mode 2 Cooling mode (not implemented) 11 Energy saving heating mode
10
2
180
Energy saving mode setpoint (ECO)
50 - 400 5.0°C – 40.0°C. Default is 180 (18.0°C)
11
2
210
Cooling setpoint (COOL)
50 - 400 5.0°C – 40.0°C. Default is 210 (21.0°C)
12
1
0
Floor sensor calibration
NB. To set a negative value, use 255 and subtract the desired value. -40 - 40 -4.0°C – 4.0°C. Default is 0 (0.0°C)
13
1
0
External sensor calibration
NB. To set a negative value, use 255 and subtract the desired value. -40 - 40 -4.0°C – 4.0°C. Default is 0 (0.0°C)
14
1
0
Temperature display
Selects which temperature is shown in the display. 0 Display setpoint temperature (Default) 1 Display measured temperature
15
1
50
Button brightness – dimmed state
Configure the brightness of the buttons, in dimmed state. 0 - 100 0 – 100% (Default 50%)
16
1
100
Button brightness – active state
Configure the brightness of the buttons, in active state. 0 - 100 0 – 100% (Default 100%)
17
1
50
Display brightness – dimmed state
Configure the brightness of the display, in dimmed state. 0 - 100 0 – 100% (Default 50%)
18
1
100
Display brightness – active state
Configure the brightness of the display, in active state. 0 - 100 0 – 100% (Default 100%)
19
2
60
Temperature report interval
Time interval between consecutive temperature reports. Temperature reports can be also sent as a result of polling. 0 Reporting of temperatures disabled 30 - 32767 30 seconds – 32767 seconds. Default is 60 seconds
2
1
0
Sensor mode
0 F-mode, floor sensor mode. (Default) 3 A2-mode, external room sensor mode
20
1
10
Temperature report hysteresis
The temperature report will be sent if there is a difference in temperature value from the previous value reported, defined in this parameter (hysteresis). Temperature reports can be also sent as a result of polling. 1 - 100 0.1°C – 10.0°C. Default is 10 (1.0°C)
21
2
60
Meter report interval
Time interval between consecutive meter reports. Meter reports can be also sent as a result of polling. 0 Reporting of metering values is disabled 30 - 32767 30 seconds – 32767 seconds. Default is 60 seconds
22
1
10
Meter report delta value
Delta value in kWh between consecutive meter reports. Meter reports can be also sent as a result of polling. 0 - 127 A delta value of 0 – 12.7 kWh will result in a metering report. Default is 10 (1.0 kWh)
3
1
0
Floor sensor type
0 10K NTC. (Default) 1 12K NTC 2 15K NTC 3 22K NTC 4 33K NTC 5 47K NTC
4
1
5
Temperature control hysteresis (DIFF I)
3 - 30 0.3°C – 3.0°C. Default is 5 (0.5°C)
5
2
50
Floor minimum temperature limit (FLo)
50 - 400 5.0°C – 40.0°C. Default is 50 (5.0°C)
6
2
400
Floor maximum temperature limit (FHi)
50 - 400 5.0°C – 40.0°C. Default is 400 (40.0°C)
7
2
50
Air (A2) minimum temperature limit (ALo)
50 - 400 5.0°C – 40.0°C. Default is 50 (5.0°C)
8
2
400
Air (A2) maximum temperature limit (AHi)
50 - 400 5.0°C – 40.0°C. Default is 400 (40.0°C)
9
2
210
Heating mode setpoint (CO)
50 - 400 5.0°C – 40.0°C. Default is 210 (21.0°C)
Sensor Multilevel V5
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Thermostat Mode V3
COMMAND_CLASS_THERMOSTAT_MODE_V3
Thermostat Setpoint V3
COMMAND_CLASS_THERMOSTAT_SETPOINT_V3
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic V2
COMMAND_CLASS_BASIC_V2
Configuration V3
COMMAND_CLASS_CONFIGURATION_V3
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V4
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V3
COMMAND_CLASS_METER_V3
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Sensor Multilevel V5
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
Supervision
COMMAND_CLASS_SUPERVISION
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Thermostat Mode V3
COMMAND_CLASS_THERMOSTAT_MODE_V3
Thermostat Setpoint V3
COMMAND_CLASS_THERMOSTAT_SETPOINT_V3
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V3
COMMAND_CLASS_VERSION_V3
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Exclusion
Removing the device:

To remove the thermostat to your home automation gateway, press Center (confirm) for 10 seconds. The display will show OFF. Press Right (down) 4 times till you see Con in the display. Now start remove device in your home automation software. Start removing mode by pressing Center (confirm) button for approximately 2 seconds. The icon will appear in the display. Removing Mode is indicated in the display by some “circling” LED segments in the display until the timeout occurs after 20 seconds or the module has been removed in the network. Confirmation will show Inc/EcL in the display. If removing fails, Err (error) will appear.
Inclusion
Adding the device:

To add the thermostat to your home automation gateway, press Center (confirm) for 10 seconds. The display will show OFF. Press Right (down) 4 times till you see Con in the display. Now start add device in your home automation software. Start adding mode by pressing Center (confirm) button for approximately 2 seconds. The icon will appear in the display. Adding Mode is indicated in the display by some “circling” LED segments in the display until the timeout occurs after 20 seconds or the module has been added in the network. Confirmation will show Inc/EcL in the display. If adding fails, Err (error) will appear.
Factory Reset
By pressing buttons Right and Center (down and confirm) for 20 seconds, the thermostat will perform a complete factory reset.

NB! Please use this procedure only when the primary controller/ gateway is missing or otherwise inoperable.
S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
IP (Ingress Protection) Rated
Product is suitable for Outdoor use and is waterproof under an IP (Ingress Protection) rating system.
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps
Switch Load Capacity Watts
The amount of switch load energy the product is rated for in Watts
Neutral Wire Required
For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.
Sensors
Sensor types supported by the product.
Thermostat HVAC Systems Supported
Indicate which HVAC system or systems are supported by the thermostat.
Thermostat Modes
Select the mode(s) supported by the thermostat.
Thermostat Power Source
Select one or more supported power sources for a thermostat.
Supported Meter Type
Indicate which type of metering is supported by the device.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).
Color
If the product is only available in one color, pick the color from the list.

 

Avaliações

Escrever uma avaliação

Heatit ZTRM2fx Recesso Z-Wave termostato para piso radiante elétrico

Heatit ZTRM2fx Recesso Z-Wave termostato para piso radiante elétrico

Heatit Z-TRM2fx é um termostato eletrônico para aquecimento de piso

29 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: