Produtos visualizados





Confianza Online


FIBARO CO SENSOR - Detector de monóxido de carbono Z-Wave Plus

FGCD-001

Novo

é um detector de monóxido de carbono Z-Wave ultra-leve, compacto e movido a bateria, projetado para ser colocado na parede.

Mais detalhes

Em estoque

99,99 €

Características tecnicas

Tecnologia Z-Wave Plus

Mais Informação

O sensor Fibaro CO protege você contra perigos invisíveis

O sensor CO da Fibaro é um detector de monóxido de carbono Z-Wave ultra-leve, compacto e alimentado por bateria projetado para ser colocado em uma parede. Sua alta sensibilidade o torna perfeito para detectar a presença de gás monóxido de carbono (CO) em um estágio inicial, a fim de evitar envenenamento por monóxido de carbono. O alarme é acusticamente sinalizado com uma sirene integrada no próprio sensor CO, indicador LED e uma mensagem Z-Wave para o controlador de automação residencial. Além disso, o dispositivo está equipado com um sensor de temperatura.

Certificado BSI


O sensor Fibaro CO possui o certificado BSI Kitemark com a licença, reconhecido mundialmente como um sinal de qualidade e segurança. Cada sensor com o símbolo BSI Kitemark está sujeito a monitoramento contínuo, que abrange o teste de produtos de rotina e a avaliação do processo de controle de qualidade de fabricação.

Simplicidade salva vidas
Notificações simples e fáceis de entender permitem que qualquer pessoa avalie a ameaça imediata.

- saudável (verde): O monóxido de carbono não foi detectado ou sua concentração é muito baixa, pode relaxar.

- Moderada (laranja): A concentração de CO pode afetar a maneira como você se sente, certifique-se de ventilar a sala, verificar a ventilação e encontrar a fonte.

- detector de CO (vermelho): o nível de CO é alto o suficiente para ameaçar a vida; siga as regras dos níveis críticos de concentração de CO.

Informação alargada da Z-Wave (Inglês)

Nome: FIBARO CO Sensor
Fabricante:FIBARO
Identificador:FGCD-001
Número de Certificação Z-Wave :ZC10-18076178
Plataforma de Hardware :ZM5101
FLiRS:Não
Tipo de Role :Reporting Sleeping Slave
Descrição breve :FIBARO CO Sensor is a compact, wall-mounted, battery-powered carbon monoxide detector.
Descrição :FIBARO CO Sensor is an ultra-light, compact, battery-powered carbon monoxide detector, designed to be placed on a wall. Its high sensitivity allows to detect the presence of the carbon monoxide (CO) gas at the early stage in order to prevent carbon monoxide poisoning. Alarm is signalled with a built-in siren, blinking LED indicator and by sending commands to Z-Wave network devices. Additionally, the device is equipped with a temperature sensor.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
1
“Lifeline” reports the device status and allows for assigning single device only (main controller by default).
2
5
“CO Alarm” is assigned to the device status - devices in this group will be switched on/off when CO Alarm status changes.
3
5
“CO Alarm” is assigned to the device status - devices in this group will receive notification when CO Alarm status changes. Useful for devices that can trigger alarms.
4
5
“CO Level” is assigned to measured CO level - devices in this group will be switched on/off after exceeding the level of CO concentration specified in parameter 14.
5
5
“Tamper Alarm” is assigned to the tamper - sends tamper alarm and cancellation frames to the associated devices.
6
5
“CO Alarm BC” is assigned to the device status - devices in this group will be switched on/off when CO Alarm status changes. Provides backward compatibility with controllers not supporting Z-Wave+ protocol.
7
5
“Tamper Alarm BC” is assigned to the tamper - sends tamper alarm and alarm cancellation frames to the associated devices. Provides backward compatibility with controllers not supporting Z-Wave+ protocol.
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
10
1
3
Commands sent to 2nd association group (CO Alarm)
This parameter defines commands sent to devices associated in 2nd association group (CO Alarm). Values of specified commands may be set in parameters 11 and 12.
11
2
255
Value of BASIC ON command sent to 2nd association group
This parameter defines the value of BASIC ON command sent to devices in 2nd association group after the CO Alarm activation. 1-99 - forcing level of associated devices 255 - setting associated devices to the last remembered state or turning them on
12
2
0
Value of BASIC OFF command sent to 2nd association group
This parameter defines the value of BASIC OFF command sent to devices in 2nd association group after the CO Alarm cancellation. 1-99 - forcing level of associated devices 255 - setting associated devices to the last remembered state or turning them on
13
1
3
Commands sent to 4th association group (CO Level)
This parameter defines commands sent to devices associated in 4th association group (CO Level). Values of specified commands may be set in parameters 16 and 19.
14
2
40
CO level required for sending BASIC ON command to 4th association group
This parameter defines the minimum level of CO concentration which exceeding will result in starting the timer set in parameter 15.
15
2
0
Time required for sending BASIC ON command to 4th association group
This parameter defines the time during which the level of CO concentration should remain above the value set in parameter 14 to send the BASIC ON command to 4th association group.
16
2
255
Value of BASIC ON command sent to 4th association group
This parameter defines the value of BASIC ON command sent to devices in 4th association group after exceeding the CO level set in parameter 14 through the time set in parameter 15. 1-99 - forcing level of associated devices 255 - setting associated devices to the last remembered state or turning them on
17
2
25
CO Level required for sending BASIC OFF command to 4th association group
This parameter defines the maximum level of CO concentration below which falling will result in starting the timer set in parameter 18.
18
2
0
Time required for sending BASIC OFF command to 4th association group
This parameter defines the time during which the level of CO concentration should remain below the value set in parameter 17 to send the BASIC OFF command to 4th association group.
19
2
0
Value of BASIC OFF command sent to 4th association group
This parameter defines the value of BASIC OFF command sent to devices in 4th association group after falling below the CO level set in parameter 17 through the time set in parameter 18. 1-99 - forcing level of associated devices 255 - setting associated devices to the last remembered state or turning them on
2
1
0
Z-Wave notifications
This parameter allows to set the actions which result in sending notifications to the Z-Wave network controller.
20
2
0
Temperature reporting time interval
Time interval (in seconds) between consecutive reports of temperature (done by built-in temperature sensor). Short time interval means more frequent communication, which results in shortened battery life.
21
1
2
Temperature reporting hysteresis
This parameter defines a minimum change in temperature resulting in a report being sent to the main Z-Wave controller.
22
1
55
Threshold of exceeding the temperature
This parameter defines the temperature level, which exceeding will result in sending actions set in parameters 2, 3 and 4.
23
1
1
CO meter activation
This parameter activates reporting the value of CO concentration level to the main Z-Wave controller.
25
1
2
CO level reporting hysteresis
This parameter defines a minimum change in CO concentration level which results in sending a new value to the main Z-Wave controller.
26
2
30
Threshold of CO meter activation
This parameter defines the CO concentration level, which exceeding will result in sending a new value to the main Z-Wave controller, according to parameter 25 settings. Adjusting the value allows to get the accurate data in case of danger and helps to save the battery in normal conditions.
3
1
0
LED diode indications
This parameter allows to set the actions which result in LED diode indications. This parameter does not apply to the most important actions, such as CO Alarm, Malfunction Alarm and Low Battery Alarm.
4
1
0
Acoustic signals
This parameter allows to set the actions which result in acoustic signals. This parameter does not apply to the most important actions, such as CO Alarm, Malfunction Alarm and Low Battery Alarm.
7
1
63
Associations in Z-Wave network security mode
Parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. It does not apply to 1st “Lifeline” association group. Parameter 7 values may be combined, e.g. 1+2=3 means that 2nd & 3rd group are sent as secure.
Basic
COMMAND_CLASS_BASIC
Application Status
COMMAND_CLASS_APPLICATION_STATUS
Association Group Information V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Battery
COMMAND_CLASS_BATTERY
Configuration
COMMAND_CLASS_CONFIGURATION
CRC16 Encapsulation
COMMAND_CLASS_CRC_16_ENCAP
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V3
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V3
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Notification V5
COMMAND_CLASS_NOTIFICATION_V5
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Sensor Alarm
COMMAND_CLASS_SENSOR_ALARM
Sensor Multilevel V10
COMMAND_CLASS_SENSOR_MULTILEVEL_V10
Version V2
COMMAND_CLASS_VERSION_V2
Wake Up V2
COMMAND_CLASS_WAKE_UP_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Inclusion
1) Place the device within direct range of the Z-Wave controller.

2) Set the main Z-Wave controller in (security/non-security) adding mode (see the controller’s manual).

3) Quickly, triple click the button located on the casing.

4) Wait for the device to be added into the system.

5) Successful adding will be confirmed by the Z-Wave controller’s message.

Exclusion
1) Place the device within direct range of the Z-Wave controller.

2) Set the main Z-Wave controller in remove mode (see the controller’s manual).

3) Quickly, triple click the button located on the casing.

4) Wait for the removing process to end.

5) Successful removing will be confirmed by the Z-Wave controller’s message.

Factory Reset
1) Press and hold the button.

2) Release the button when LED indicator glows white.

3) Click the button when LED indicator glows yellow.

4) After few seconds the device will be reset (confirmed by red LED indicator).



Resetting the device is not the recommended way of removing the device from the Z-Wave network. use the reset procedure only if the primary controller is missing or inoperable.

Device Wake-Up
The CO Sensor needs to be woken up to receive information about the new configuration from the Z-Wave controller, like parameters and associations. To wake up the sensor manually click the button located on the casing.
Battery Quantity
Enter the number of batteries of the designated type that the product uses.
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.
Color
If the product is only available in one color, pick the color from the list.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Sensors
Sensor types supported by the product.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).

 

Avaliações

Escrever uma avaliação

FIBARO CO SENSOR - Detector de monóxido de carbono Z-Wave Plus

FIBARO CO SENSOR - Detector de monóxido de carbono Z-Wave Plus

é um detector de monóxido de carbono Z-Wave ultra-leve, compacto e movido a bateria, projetado para ser colocado na parede.

14 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: