AEOTEC - Dual Nano Switch com medição de consumo Z-Wave

Características tecnicas

Tecnologia	Z-Wave Plus
Recurso	Medição de Consumo

Mais Informação

Verifique todas as opções. Controle qualquer plug. De todos os lados. Sem fio.
Tomadas e interruptores de luz são invenções incríveis. Eles literalmente mudaram o mundo. Mas se você não estiver próximo a eles ou não puder alcançá-los, eles são limitados.

Agora não. O futuro é mais inteligente. Esta é a sua casa O Switch Dual Nano fornece controle sem fio completo de seus switches e soquetes.

Controle total
O Dual Nano Switch oferece controle total, fácil. Extremamente pequeno, cada Switch Dual Nano é instalado de forma invisível atrás de qualquer um dos switches ou tomadas existentes em sua casa. Basta desparafusar o painel frontal, instalar o switch nano duplo atrás dele e agora você tem controle sem fio completo. Seus interruptores antigos são instantaneamente modernos e conectados.

Com o AEOTEC Nano Switch, todas as instalações elétricas comutáveis e não reguláveis (por exemplo, iluminação, plugues ...) podem ser integradas em uma rede Z-Wave. Portanto, a carga conectada pode ser comutada sem fio via Z-Wave e localmente por meio do interruptor de parede existente. Além disso, o ZW132 possui uma função de medição de energia embutida que permite detectar o consumo de energia exato da carga conectada.

O módulo de rádio compacto (60% menor que seu antecessor Micro Smart Switch) é colocado em uma caixa de parede logo atrás do switch normal. A chave não está mais conectada diretamente à carga, mas atua como um dispositivo de entrada para a inserção AEOTEC que controla a carga. A chave apenas envia um sinal de controle para a inserção que controla a carga novamente. A solução funciona com todos os designs de switch. Você pode usar uma chave momentânea ou de alternância. Recomenda-se a utilização de caixas de parede com profundidade de 65 mm. Mas caixas menores com uma profundidade de apenas 45 mm também podem ser usadas se houver espaço suficiente atrás do switch. O espaço disponível depende do tamanho do switch tradicional, das dimensões da caixa de parede e da quantidade de fiação adicional colocada nesta caixa.

caracteristicas:

Módulo de rádio embutido
Carga máxima: máx. 2x 1150W
Função de medição de energia
Integre as instalações existentes (iluminação, tomadas ...) em uma rede Z-Wave
Funciona com interruptores momentâneos ou alternativos
Tensão: 230 V, 50 Hz
Fiação: condutor neutro necessário
Tecnologia sem fio: Z-Wave Plus

Informação alargada da Z-Wave (Inglês)

Nome: Dual Nano Switch

Fabricante:Aeotec

Identificador:ZW132-F

Número de Certificação Z-Wave :ZC10-18106252

Plataforma de Hardware :ZM5101

FLiRS:Não

Tipo de Role :Always On Slave

Descrição breve :Aeotec Dual Nano Switch is a Z-Wave Smart Switch specifically used to enable Z-Wave command and control (on/off) of any wall switches also provides energy metering.

Descrição :Aeotec Dual Nano Switch is a Z-Wave Smart Switch specifically used to enable Z-Wave command and control (on/off) of any wall switches. It can report immediate wattage consumption or kWh energy usage over a period of time. In the event of power failure, non-volatile memory retains all programmed information relating to the unit’s operating status. It can connect to 2 external manual switches to control the load ON/OFF independently. Its surface has a pin socket, which can be used for connecting to the touch panel, so you can also use the touch panel to control the Dual Nano Switch. The Dual Nano Switch is also a security Z-Wave device and supports Over The Air (OTA) feature for the products firmware upgrade.

Descarregue o manual a partir de aqui.

Grupo

Nodos máximos

Descrição

1

5

Z-Wave Plus Lifeline. When the load state of Dual Nano Switch (turn on/off the load) is changed, the Hail CC and Basic Report (configured by parameter 80) can be sent to the associated nodes in this group.

2

5

Forward the Basic Set, Switch All, Scene Activation Set to associated nodes in Group 2 when the Dual Nano Switch receives the Basic Set, Switch All, Scene Activation Set commands from main controller. (E.g. Send/forward Basic Set to control the other nodes in association Group 2)

3

5

Send Basic Set (configured by parameter 0x51 ) to the associated nodes in Group 3 when the external switch S1 is operated. Note: The Switch Mode of external switch S1 should be identified successfully, which means that the value of Configuration parameter 0x78 should be non-zero, then the Basic Set can be sent to the associated nodes in Group 3 via triggering the S1 switch.

4

5

Send Basic Set (configured by parameter 0x52) to the associated nodes in Group 4 when the external switch S2 is operated. Note: The Switch Mode of external switch S2 should be identified successfully, which means that the value of Configuration parameter 0x79 should be non-zero, then the Basic Set can be sent to the associated nodes in Group 3 via triggering the S2 switch.

Número

Tamanho (Bytes)

Valor por defeito

Nome

Descrição

100

1

0

Set parameter 101-103 to default value.

101

4

0

To set which reports need to be sent in Report group 1.

102

1

0

To set which reports need to be sent in Report group 2.

103

1

0

To set which reports need to be sent in Report group 3.

110

1

0

Set parameter 111-113 to default value.

111

4

10

Set the interval of automatic report for Report group 1.

112

4

600

Set the interval of automatic report for Report group 2.

113

4

600

Set the interval of automatic report for Report group 2.

Set the interval of automatic report for Report group 3.

120

1

0

Configure the external switch mode for S1.

121

1

0

Configure the external switch mode for S2.

122

1

3

Set the control destination for external switch

20

1

0

Configure the output status after re-power on it.

252

1

0

Lock/unlock configuration parameters

Lock/unlock configuration parameters.

255

4

0

Reset the Dual Nano Switch

Reset the Dual Nano Switch to factory default.

3

1

Current Overload Protection.

Output Load will be turned off automatically after 30 seconds and if the current overrun 1.5A.

4

1

0

Overheat protection.

Output Load will be turned off automatically after 30 seconds and if the temperature of product inside exceeds 100 ℃.

80

1

0

To set which notification would be sent to the associated devices (Group 1)

To set which notification would be sent to the associated devices (Group 1) when the state of Nano Dimmer’s load is changed.

81

1

To set which notification would be sent to the associated nodes in association group 3

To set which notification would be sent to the associated nodes in association Group 3 when using the external switch 1 to switch the loads.

82

1

To set which notification would be sent to the associated nodes in association group 4

To set which notification would be sent to the associated nodes in association Group 4 when using the external switch 2 to switch the loads.

83

1

0

Configure the state of LED when it is in 3 modes

Configure the state of LED when it is in 3 modes (Energy mode, Momentary indicate mode, Night light mode)

84

1

301991936

Set the ON/OFF time of the LED when it is in Night light mode.

86

4

8327680

Set appointment 1

Set the ON time of output load.

87

4

8327680

Set appointment 2

Set the OFF time of output load.

90

1

0

Enables/disables parameter 91 and 92 below:

Enables/disables the function of parameter 91 and 92.

91

2

25

Set the threshold value of wattage.

Threshold change in wattage (in terms of wattage) to induce an automatic report.

92

1

5

Set the threshold value of wattage.

Threshold change in wattage (in terms of percentage) to induce an automatic report.

Basic

COMMAND_CLASS_BASIC

Hail

COMMAND_CLASS_HAIL

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic

COMMAND_CLASS_BASIC

Clock

COMMAND_CLASS_CLOCK

Configuration

COMMAND_CLASS_CONFIGURATION

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V3

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V3

COMMAND_CLASS_METER_V3

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel V4

COMMAND_CLASS_MULTI_CHANNEL_V4

Notification V4

COMMAND_CLASS_NOTIFICATION_V4

Powerlevel

COMMAND_CLASS_POWERLEVEL

Scene Activation

COMMAND_CLASS_SCENE_ACTIVATION

Scene Actuator Conf

COMMAND_CLASS_SCENE_ACTUATOR_CONF

Security S0

COMMAND_CLASS_SECURITY

Switch All

COMMAND_CLASS_SWITCH_ALL

Switch Binary

COMMAND_CLASS_SWITCH_BINARY

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Inclusion

Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Action button that you can find on the product's housing.

Exclusion

Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Action button that you can find on the product's housing.

Additional Special Features

Support ""Over the Air Firmware Updating"" and “Z-Wave Security”.

Factory Reset

Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable.

Switch Type

Describes the type of operator for a switch.

Z-Wave Scene Type

Indicates which of the two types of Z-Wave scene command classes are supported. Scenes or Central Scene

Electric Load Type

Select the electric load type(s) supported by the device.

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

Supported Meter Type

Indicate which type of metering is supported by the device.

Supported Notification Types

Select the Notification Types that the product handles (controllers), or sends (slaves).