Produtos visualizados





Confianza Online


HELTUN - interruptor de toque Z-Wave + 5 canais (cor branca)

HE211401

Novo

O interruptor de parede do painel de toque de 5 canais da HELTUN substitui um interruptor de parede existente e permite controles manuais ou remotos (On / Off). Cor branca

Mais detalhes

Não disponível

129,99 €

Características tecnicas

Tecnologia Z-Wave Plus

Mais Informação

É o seu conforto. Assuma o controle do mesmo.
O interruptor de toque de parede de 5 canais HELTUN substitui um interruptor de parede existente e permite o controlo manual ou remoto de interruptores (on / off) para luzes, persianas, motores e sistemas de aquecimento com uma carga máxima de 5A para cada canal.

Elegância
Potente, eficiente e bem desenhado, o HELTUN é o interruptor mais fino e elegante do mercado. Equipado com um copo de cristal, o seu invólucro de plástico reciclado resistente ao fogo e curto-circuito tem uma espessura de apenas 9 mm.

Design
O HELTUN adapta-se perfeitamente ao seu design interior e está disponível em 24 combinações: 4 cores de caixilho (prateado, cromado, preto e branco) e 6 tipos de vidro (branco, preto, amarelo, verde, vermelho e azul), pode escolher qualquer estilo que se adapte ao seu gosto.

Sensores internos
Os switches HELTUN também possuem sensores integrados de temperatura, umidade e luz.

Sensores Heltun e Toque

Entradas e saídas
A entrada de energia principal é 100-250VAC. O Heltun Switcher possui 5 saídas de relé, cada uma com uma carga máxima de 5A. Também possui duas entradas independentes para canais de relés que permitem controlar sistemas com fontes de alimentação diferentes ou usar as saídas como contatos secos. Por exemplo, para ligar / desligar a luz de 220VAC e controlar a válvula motorizada com uma fonte de alimentação de 24VCC.

A entrada 1 com a fonte de alimentação necessária é para os canais de relé 1, 2 e 3, que podem ser carregados até um máximo de 15A.

A entrada 2 com a fonte de alimentação necessária é para os canais de relé 4 e 5, que podem ser carregados até um máximo de 10A.

Interruptor de toque das conexões traseiras Heltun

Conheça o seu consumo de energia
Com o sistema de consumo de energia integrado no interruptor HELTUN, você pode monitorar com precisão a quantidade de energia usada durante um determinado dia, semana ou mês para cada canal. Simplesmente especifique o consumo de carga em watts para cada canal de relé e a lógica especial calculará o consumo total em relação ao tempo decorrido desde que a saída esteja no estado ON.

Funções personalizadas
1) Cada botão de toque pode ser configurado para controlar qualquer saída de relé. Até cinco saídas de relé podem ser controladas por botão.

2) 4 modos diferentes para cada controle de relé: somente ON, somente OFF, invertido, hold (mudar para On quando o botão for pressionado e mudar para Off quando o botão for liberado)

3) As saídas do relé podem ser controladas pelo temporizador: pressione o botão que o relé ligará e após o tempo especificado ele será desligado automaticamente. Esta função pode ser usada para abrir / fechar portas de garagem, persianas, cortinas, etc.

4) Cada botão, luz de fundo e relé é completamente independente. Eles são gerenciados pelo controlador principal ou dispositivo associado. Nesse estado, os botões podem ser usados para executar cenários e a luz de fundo pode indicar o modo ou o status do dispositivo.

Botões
O painel possui 5 botões de toque que são super sensíveis e reagem mesmo antes do contato físico, na verdade o tratamento é feito a uma distância de 1-2mm. Cada botão tem uma luz de fundo de duas cores (vermelho e azul).

Você pode controlar manualmente 4 níveis de brilho diferentes de cada luz de fundo de cor, ajustando o valor nas configurações ou no modo automático. O controle automático de brilho ajusta de forma transparente o nível da luz de fundo das teclas às condições de luz ambiente, facilitando o uso mesmo no escuro.

Interruptor de toque Heltun

Fácil de instalar
As unidades HELTUN podem ser facilmente instaladas em qualquer suporte de parede padrão (retangular ou redondo). Nenhuma habilidade especial é necessária para a instalação.

Certificado Z-Wave Plus S2
Conecte seus dispositivos HELTUN ao sistema de controle de automação residencial usando o mais recente chip seguro Z-Wave Plus com a nova estrutura Security 2 (S2) (método de criptografia AES 256 para transferência de dados).

O Switcher HELTUN é compatível com todos os controladores e dispositivos com certificação Z-WAVE.

Com o controlador Z-Wave, você pode gerenciar todas as funções dos switches por meio de um aplicativo móvel, incluindo a simulação de cada pressionamento de botão, a exibição de gráficos precisos de consumo de energia e muito mais.

Além disso, até 10 dispositivos separados podem ser conectados ao switch. Você pode combinar qualquer relé compatível com Z-Wave com a chave Heltun e controlar as travas das portas, válvulas, persianas, cortinas e outros sistemas motorizados.

FUNÇÕES

Interruptor de toque de 5 canais Z-Wave +
Inclusão / exclusão em uma rede Z-Wave
Controle por associação de 10 dispositivos na rede
Personalização de funções da tecla de toque
Ativar apenas o relé
Desativar apenas o relé
Inverta o status do relé
Função Hold (botão de pressão)
Escolhendo o canal de retransmissão para cada botão
Até 5 canais diferentes podem ser controlados com um botão
Relé de saída controlado pelo tempo
Configurar cada botão para controlar outro dispositivo no grupo de associação
Cores da luz de fundo invertida
Medidor de consumo de energia para cada canal
Calibração de sensores de temperatura
Brilho ajustável da tela LCD: automático ou manual
Cancelamento do medidor de consumo
Retornar para as configurações de fábrica
Função OTA (atualização de firmware Over The Air)
AS ESPECIFICAÇÕES TÉCNICAS

Dimensões do quadro dianteiro: 89x89x9mm
Dimensões traseiras: 53x53x28mm
Material: Plástico retardador de chama, vidro temperado
Cores da estrutura: branco
Cores de vidro: branco
5 botões de toque capacitivos sensíveis
Luz de fundo LED vermelha e azul para cada botão
4 níveis de brilho ajustáveis para iluminação de fundo
Saída de relé de 5 canais, carga resistiva de até 5A cada
2 entradas independentes para o canal de retransmissão
Temperatura de operação: -10 ° C a +60 ° C
Potência: 100V - 230VAC, 50Hz / 60Hz
Consumo de energia: 2 W
Carga resistiva máxima: 5A para cada canal
Tempo de vida do relé: 100.000 interruptores
Sensor de luz ambiente interno
Sensor de temperatura interna
Faixa de medição: -40 ° C a +125 ° C
Precisão: ± 0,5 ° C
Sensor de umidade interna
Faixa de medição: 0 a 80% RH
Precisão: ± 3,0% RH
Medidor de consumo de energia
Classe de proteção: IP21
Freqüência de onda Z: EU-868/869 MHz
Z-Wave SDK: V6.71
Módulo Z-Wave Plus: ZM5202

Download

Informação alargada da Z-Wave (Inglês)

Nome: Touch Panel Switch Quinto
Fabricante:HELTUN
Identificador:HE-TPS05
Número de Certificação Z-Wave :ZC12-20040048
Plataforma de Hardware :ZGM130
FLiRS:Não
Tipo de Role :Always On Slave
Descrição breve :Advanced Programmable Z-Wave Plus v2 Wall Touch Panel Switch Quinto—with S2 security and SmartStart on the Z-Wave 700 platform.
Descrição :The HELTUN HE-TPS05 is an advanced programmable Z-Wave Plus v2 touch panel switch that controls many devices, including lights, dimmers, blinds, curtains, door locks, motorized valves, roller shutters, and more. Features: • Five-channel 5-amp relays with dry contact inputs • Five programmable touch buttons with two-color backlights • All buttons fully customizable to control one to five relays • Five modes configurable for each button • Each relay may be controlled by a timer or on a week schedule • Separate relays & backlights control from gateway or associated devices • Controls Scenes of gateway by touch buttons (pressed, held, released) • Built-in light, temperature, and humidity sensors • Power Consumption logic monitors energy usage • 20 association groups • Incorporates HELTUN Advanced Zero-Cross Technology • ‘Impossibly thin’ at only 9mm The HELTUN HE-TPS05 is part of an entire line of smart, connected products designed to provide the best technology has to offer without compromising stylish living.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
1
This is the Lifeline Group 1 which sends status (lifeline) reports to the primary controller.
2
1
Group 2 – “Touch 1 Basic Set”: is assigned to touch N1. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
3
1
Group 3 – “Touch 1 Multilevel Set”: is assigned to touch N1. It sends MULTILEVEL SWITCH command class frame when touch N1 was held. Is used to send UP/DOWN command to the associated devices.
4
1
Group 4 – “Touch 2 Basic Set”: is assigned to touch N2. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
5
1
Group 5 – “Touch 2 Multilevel Set”: is assigned to touch N2. It sends MULTILEVEL SWITCH command class frame when touch N1 was held. Is used to send UP/DOWN command to the associated devices.
6
1
Group 4 – “Touch 3 Basic Set”: is assigned to touch N3. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
7
1
Group 7 – “Touch 3 Multilevel Set”: is assigned to touch N3. It sends MULTILEVEL SWITCH command class frame when touch N1 was held. Is used to send UP/DOWN command to the associated devices.
8
1
Group 8 – “Touch 4 Basic Set”: is assigned to touch N4. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
9
1
Group 9 – “Touch 4 Multilevel Set”: is assigned to touch N4. It sends MULTILEVEL SWITCH command class frame when touch N1 was held. Is used to send UP/DOWN command to the associated devices.
10
1
Group 10 – “Touch 5 Basic Set”: is assigned to touch N5. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
11
1
Group 11 – “Touch 5 Multilevel Set”: is assigned to touch N5. It sends MULTILEVEL SWITCH command class frame when touch N1 was held. Is used to send UP/DOWN command to the associated devices.
12
1
Group 12 – “LED 1 Basic Set”: is assigned to LED N1. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
13
1
Group 13 – “LED 2 Basic Set”: is assigned to LED N2. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
14
1
Group 14 – “LED 3 Basic Set”: is assigned to LED N3. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
15
1
Group 14 – “LED 4 Basic Set”: is assigned to LED N4. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
16
1
Group 16 – “LED 5 Basic Set”: is assigned to LED N5. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
17
1
Group 17 – “Relay 1 Basic Set”: is assigned to relay N1. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
18
1
Group 18 – “Relay 2 Basic Set”: is assigned to relay N2. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
19
1
Group 19 – “Relay 3 Basic Set”: is assigned to relay N3. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
20
1
Group 20 – “Relay 4 Basic Set”: is assigned to relay N4. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
21
1
Group 21 – “Relay 5 Basic Set”: is assigned to relay N5. Is used to send Basic Set ON (value 255) and Basic Set OFF (value 0) commands to the associated devices.
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
1
1
1
TIME CORRECTION
Time correction by controller
10
1
15
TOUCH SENSITIVITY
Touch buttons sensitivity: 10=Supper sensitive. 50=lowest sensitivity.
11
1
0
TEMP SENSOR CORRECTION
Temperature sensor calibration, x10
12
1
1
BACKLIGHT ACTIVE COLOR
Active state backlight color
13
1
1
BACKLIGHT AUTO BRIGHTNESS
Backlight auto-brightness control
14
1
10
BACKLIGHT MANUAL BRIGHTNESS LEVEL
Backlight brightness in manual mode. The Backlight Brightness Level Parameter will take effect when Parameter 13 is set to Manual Control (value = 0).
15
1
1
BACKLIGHT1 CONTROL SOURCE
Backlight 1 control source
16
1
1
BACKLIGHT2 CONTROL SOURCE
Backlight 2 control source
17
1
1
BACKLIGHT3 CONTROL SOURCE
Backlight 3 control source
18
1
1
BACKLIGHT4 CONTROL SOURCE
Backlight 4 control source
19
1
1
BACKLIGHT5 CONTROL SOURCE
Backlight 5 control source
2
1
1
WEEKDAY
The day of the week (starting from Monday)
20
1
1
RELAY1 CONTROL SOURCE
Relay 1 control source
21
1
2
RELAY2 CONTROL SOURCE
Relay 2 control source
22
1
3
RELAY3 CONTROL SOURCE
Relay 3 control source
23
1
4
RELAY4 CONTROL SOURCE
Relay 4 control source
24
1
5
RELAY5 CONTROL SOURCE
Relay 5 control source
25
1
1
HOLD1 CONTROL MODE
Hold control mode for touch button 1
26
1
1
HOLD2 CONTROL MODE
Hold control mode for touch button 2
27
1
1
HOLD3 CONTROL MODE
Hold control mode for touch button 3
28
1
1
HOLD4 CONTROL MODE
Hold control mode for touch button 4
29
1
1
HOLD5 CONTROL MODE
Hold control mode for touch button 5
3
1
0
HOUR
Time Hour
30
1
1
CLICK1 CONTROL MODE
Click control mode for touch button 1
31
1
1
CLICK2 CONTROL MODE
Click control mode for touch button 2
32
1
1
CLICK3 CONTROL MODE
Click control mode for touch button 3
33
1
1
CLICK4 CONTROL MODE
Click control mode for touch button 4
34
1
1
CLICK5 CONTROL MODE
Click control mode for touch button 5
35
2
0
RELAY1 TIMER DURATION
Timer mode duration for button 1. This parameter specifies the duration in seconds for the Timer mode (value 5 or 6 in Parameters 30). Press the button and the relay output goes to ON/OFF for the specified time then changes back to OFF/ON. This function can be used to open/close garage doors, blinds, curtains, etc. or to turn attached devices like security OFF for a short time. The time values can be configured from 0 to 43200 sec (12 hours). Note: If the parameter value is set to “0” it will operate as a short contact (about 0.5 sec).
36
2
0
RELAY2 TIMER DURATION
Timer mode duration for button 2. This parameter specifies the duration in seconds for the Timer mode (value 5 or 6 in Parameters 31). Press the button and the relay output goes to ON/OFF for the specified time then changes back to OFF/ON. This function can be used to open/close garage doors, blinds, curtains, etc. or to turn attached devices like security OFF for a short time. The time values can be configured from 0 to 43200 sec (12 hours). Note: If the parameter value is set to “0” it will operate as a short contact (about 0.5 sec).
37
2
0
RELAY3 TIMER DURATION
Timer mode duration for button 3. This parameter specifies the duration in seconds for the Timer mode (value 5 or 6 in Parameters 32). Press the button and the relay output goes to ON/OFF for the specified time then changes back to OFF/ON. This function can be used to open/close garage doors, blinds, curtains, etc. or to turn attached devices like security OFF for a short time. The time values can be configured from 0 to 43200 sec (12 hours). Note: If the parameter value is set to “0” it will operate as a short contact (about 0.5 sec).
38
2
0
RELAY4 TIMER DURATION
Timer mode duration for button 4. This parameter specifies the duration in seconds for the Timer mode (value 5 or 6 in Parameters 33). Press the button and the relay output goes to ON/OFF for the specified time then changes back to OFF/ON. This function can be used to open/close garage doors, blinds, curtains, etc. or to turn attached devices like security OFF for a short time. The time values can be configured from 0 to 43200 sec (12 hours). Note: If the parameter value is set to “0” it will operate as a short contact (about 0.5 sec).
39
2
0
RELAY5 TIMER DURATION
Timer mode duration for button 5. This parameter specifies the duration in seconds for the Timer mode (value 5 or 6 in Parameters 34). Press the button and the relay output goes to ON/OFF for the specified time then changes back to OFF/ON. This function can be used to open/close garage doors, blinds, curtains, etc. or to turn attached devices like security OFF for a short time. The time values can be configured from 0 to 43200 sec (12 hours). Note: If the parameter value is set to “0” it will operate as a short contact (about 0.5 sec).
4
1
0
MINUTE
Time Minute
40
1
0
RELAY INVERSE GROUP1
Group 1 relay inverse mode. The valid values are the following: 0, 12, 13, 14, 15, 21, 23, 24, 25, 31, 32, 34, 35, 41, 42, 43, 45, 51, 52, 53, 54
41
1
0
RELAY INVERSE GROUP2
Group 2 relay inverse mode. The valid values are the following: 0, 12, 13, 14, 15, 21, 23, 24, 25, 31, 32, 34, 35, 41, 42, 43, 45, 51, 52, 53, 54
42
4
0
RELAY CONTROL SCENARIO1
Relays control by sensors Group 1 0, 10000000 … 53112359 Encoded as 8 digit value (ABCDEFGH): A: Relay number (1.. 5) B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control) C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than) D: State Change, 0- Switch OFF, 1- Switch ON EFGH: Condition Value Sensor Value for Control modes 0-2 Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
43
4
0
RELAY CONTROL SCENARIO2
Relays control by sensors Group 2 0, 10000000 … 53112359 Encoded as 8 digit value (ABCDEFGH): A: Relay number (1.. 5) B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control) C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than) D: State Change, 0- Switch OFF, 1- Switch ON EFGH: Condition Value Sensor Value for Control modes 0-2 Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
44
4
0
RELAY CONTROL SCENARIO3
Relays control by sensors Group 3 0, 10000000 … 53112359 Encoded as 8 digit value (ABCDEFGH): A: Relay number (1.. 5) B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control) C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than) D: State Change, 0- Switch OFF, 1- Switch ON EFGH: Condition Value Sensor Value for Control modes 0-2 Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
45
4
0
RELAY CONTROL SCENARIO4
Relays control by sensors Group 4 0, 10000000 … 53112359 Encoded as 8 digit value (ABCDEFGH): A: Relay number (1.. 5) B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control) C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than) D: State Change, 0- Switch OFF, 1- Switch ON EFGH: Condition Value Sensor Value for Control modes 0-2 Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
46
4
0
RELAY CONTROL SCENARIO5
Relays control by sensors Group 5 0, 10000000 … 53112359 Encoded as 8 digit value (ABCDEFGH): A: Relay number (1.. 5) B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control) C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than) D: State Change, 0- Switch OFF, 1- Switch ON EFGH: Condition Value Sensor Value for Control modes 0-2 Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
47
4
0
RELAY CONTROL SCENARIO6
Relays control by sensors Group 6 0, 10000000 … 53112359 Encoded as 8 digit value (ABCDEFGH): A: Relay number (1.. 5) B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control) C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than) D: State Change, 0- Switch OFF, 1- Switch ON EFGH: Condition Value Sensor Value for Control modes 0-2 Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
48
4
0
RELAY CONTROL SCENARIO7
Relays control by sensors Group 7. 0, 10000000 … 53112359 Encoded as 8 digit value (ABCDEFGH): A: Relay number (1.. 5) B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control) C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than) D: State Change, 0- Switch OFF, 1- Switch ON EFGH: Condition Value Sensor Value for Control modes 0-2 Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
49
4
0
RELAY CONTROL SCENARIO8
Relays control by sensors Group 8 0, 10000000 … 53112359 Encoded as 8 digit value (ABCDEFGH): A: Relay number (1.. 5) B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control) C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than) D: State Change, 0- Switch OFF, 1- Switch ON EFGH: Condition Value Sensor Value for Control modes 0-2 Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
5
1
10
METER REPORT INTERVAL
Energy Consumption Meter Consecutive Report Interval, minutes
50
4
0
RELAY CONTROL SCENARIO9
Relays control by sensors Group 9 0, 10000000 … 53112359 Encoded as 8 digit value (ABCDEFGH): A: Relay number (1.. 5) B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control) C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than) D: State Change, 0- Switch OFF, 1- Switch ON EFGH: Condition Value Sensor Value for Control modes 0-2 Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
51
4
0
RELAY CONTROL SCENARIO10
Relays control by sensors Group 10 0, 10000000 … 53112359 Encoded as 8 digit value (ABCDEFGH): A: Relay number (1.. 5) B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control) C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than) D: State Change, 0- Switch OFF, 1- Switch ON EFGH: Condition Value Sensor Value for Control modes 0-2 Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
52
2
0
RELAY1 LOAD POWER
Power load consumption (in Watts) Relay channel 1 in order to calculate total energy consumption relative to the time each relay is ON.
53
2
0
RELAY2 LOAD POWER
Power load consumption (in Watts) Relay channel 2 in order to calculate total energy consumption relative to the time each relay is ON.
54
2
0
RELAY3 LOAD POWER
Power load consumption (in Watts) Relay channel 3 in order to calculate total energy consumption relative to the time each relay is ON.
55
2
0
RELAY4 LOAD POWER
Power load consumption (in Watts) Relay channel 4 in order to calculate total energy consumption relative to the time each relay is ON.
56
2
0
RELAY5 LOAD POWER
Power load consumption (in Watts) Relay channel 5 in order to calculate total energy consumption relative to the time each relay is ON.
57
1
0
TOUCH1 ASSOCIATION MODE
Touch control mode for associations with touch button 1. This parameter is intended for use when Multilevel Switch Group Associations (Groups 3, 5, 7, 9, & 11) have been activated. Defines the logic of values changing if one the touch button has been held for more than one second.
58
1
0
TOUCH2 ASSOCIATION MODE
Touch control mode for associations with touch button 2. This parameter is intended for use when Multilevel Switch Group Associations (Groups 3, 5, 7, 9, & 11) have been activated. Defines the logic of values changing if one the touch button has been held for more than one second.
59
1
0
TOUCH3 ASSOCIATION MODE
Touch control mode for associations with touch button 3. This parameter is intended for use when Multilevel Switch Group Associations (Groups 3, 5, 7, 9, & 11) have been activated. Defines the logic of values changing if one the touch button has been held for more than one second.
6
1
10
SENSORS REPORT INTERVAL
Sensors Consecutive Report Interval
60
1
0
TOUCH4 ASSOCIATION MODE
Touch control mode for associations with touch button 4. This parameter is intended for use when Multilevel Switch Group Associations (Groups 3, 5, 7, 9, & 11) have been activated. Defines the logic of values changing if one the touch button has been held for more than one second.
61
1
0
TOUCH5 ASSOCIATION MODE
Touch control mode for associations with touch button 5. This parameter is intended for use when Multilevel Switch Group Associations (Groups 3, 5, 7, 9, & 11) have been activated. Defines the logic of values changing if one the touch button has been held for more than one second.
7
1
5
TEMPERATURE REPORT THRESHOLD
Temperature difference to send to controller, value X 10
8
1
2
HUMIDITY REPORT THRESHOLD
Humidity difference to send to controller, value X 10
9
1
50
LIGHT REPORT THRESHOLD
Luminance difference to send to controller in %
Application Status
COMMAND_CLASS_APPLICATION_STATUS
Association Group Information V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic V2
COMMAND_CLASS_BASIC_V2
Central Scene V3
COMMAND_CLASS_CENTRAL_SCENE_V3
Clock
COMMAND_CLASS_CLOCK
Configuration V4
COMMAND_CLASS_CONFIGURATION_V4
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V5
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
Indicator V3
COMMAND_CLASS_INDICATOR_V3
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V5
COMMAND_CLASS_METER_V5
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Sensor Multilevel V11
COMMAND_CLASS_SENSOR_MULTILEVEL_V11
Supervision
COMMAND_CLASS_SUPERVISION
Switch Binary V2
COMMAND_CLASS_SWITCH_BINARY_V2
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V3
COMMAND_CLASS_VERSION_V3
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Where to find S2 DSK on product
The device DSK and QR code are printed on the HE-TPS05 back panel plus on the additional Security Card included in the HE- TPS05 packaging.
Classic Inclusion
To add the HE-TPS05 to a Z-Wave Network (i.e. “inclusion”), do the following:

1. Start the inclusion mode from the gateway/controller.

2. To start the inclusion process on the HE-TPS05, simultaneously press the two bottom touch buttons and hold them for three seconds.

3. The two upper buttons will then sequentially blink ‘blue-red’.

4. If the inclusion has been successful, the two upper buttons will turn blue for three seconds.

5. If the inclusion was not successful, the two upper buttons will turn red for three seconds. In that case repeat the inclusion process.
Classic Exclusion
To remove the HE-TPS05 from a Z-Wave Network (i.e. “exclusion”), do the following:

1. Start the exclusion mode from the gateway/controller.

2. To start the exclusion process on the HE-TPS05, simultaneously press the two bottom touch buttons and hold them for three seconds.

3. Two upper buttons will sequentially blink blue-red.

4. If the exclusion has been successful, the two upper buttons will turn red for three seconds.

5. If the exclusion was not successful, the two upper buttons will turn blue for three seconds. In that case repeat the exclusion process.

Factory Reset Procedure
To reset the HE-TPS05 to factory defaults, simultaneously press the two bottom buttons and single central touch button, and hold all three for five seconds. If successful, the two upper buttons will turn blue for three seconds then the device will restart.

NOTE: This factory reset procedure will change all parameters to the original factory default values and will also exclude the device from any associated Z-Wave network.

Please use Factory Reset only when the primary network controller is missing or otherwise inoperable.
S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Neutral Wire Required
For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.
Z-Wave Scene Type
Indicates which of the two types of Z-Wave scene command classes are supported. Scenes or Central Scene
Switch Type
Describes the type of operator for a switch.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps

 

Avaliações

Escrever uma avaliação

HELTUN - interruptor de toque Z-Wave + 5 canais (cor branca)

HELTUN - interruptor de toque Z-Wave + 5 canais (cor branca)

O interruptor de parede do painel de toque de 5 canais da HELTUN substitui um interruptor de parede existente e permite controles manuais ou remotos (On / Off). Cor branca

15 outros produtos na mesma categoria: