Produtos visualizados





Confianza Online


AEOTEC Bombilla LED 6 Multi-Color (E27)

AEOEZWA002

Novo

Em estoque

49,99 €

Características tecnicas

Tecnologia Z-Wave Plus

Informação alargada da Z-Wave (Inglês)

Nome: LED Bulb 6:Multi-Colour
Fabricante:Aeotec
Identificador:ZWA002-C
Número de Certificação Z-Wave :ZC10-18046097
Plataforma de Hardware :ZM5101
FLiRS:Não
Tipo de Role :Always On Slave
Descrição breve :RGBW: dimmable from 5% to 100%, tunable from 1800K to 6500K, and 16 million colors
Descrição :✓ Standard form factor and appearance of the light bulb with 800 lm output ✓ RGBW: dimmable from 5% to 100%, tunable from 1800K to 6500K, and 16 million colors ✓ Possible to be included in groups, scenes, or schedules ✓ Suitable for indoor lighting: Corridors, Bedroom, Living Room, etc.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
1
Set Configuration parameter 0x50 0: nothing. 1: Send the Basic Report. 2. Send Device Reset Locally CC
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
1
1
0
User custom mode for LED animations.
User custom mode for LED animations. 0 = Disable custom mode. 1= Blink Colors in order mode. 2=Randomized blink color mode
16
1
20
Ramp rate when dimming using Multilevel Switch V1 CC in 100ms
Ramp rate when dimming using Multilevel Switch V1 CC in 100ms Value range = 0x00 -0x64
2
1
0
Enable/Disable Strobe over Custom Color.
Enable/Disable Strobe over Custom Color. 0 = Disable. 1 = Enable. Others = Ignore.
3
1
50
Set the rate of change to next color in Custom Mode.
Set the rate of change to next color in Custom Mode. Value1 ~ Value4: Value Range = 5 - 8640000 (50 - 86400000ms)
4
1
1
Set color that LED Bulb blinks in (Blink Mode)
Set color that LED Bulb blinks in (Blink Mode) -128 to 127 corresponds with the unsigned values 0 to 255 or hex values 0x00 to 0xFF
80
1
1
Enable to send notifications to associated devices (Group 1) when the state of LED Bulb is changed.
Enable to send notifications to associated devices (Group 1) when the state of LED Bulb is changed. 0 = Nothing. 1= Basic CC report.
81
2
2700
The user can configure the parameter to adjust the color component Warm White.
The user can configure the parameter to adjust the color component Warm White. Value range =Warm White(0x0A8C(2700k) ~ 0x1387 (4999k))
82
2
6500
The user can configure the parameter to adjust the color component Cold White.
The user can configure the parameter to adjust the color component Cold White. Value rang = Cold White (0x1388 (5000k) ~ 0x1964 (6500k))
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V2
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Switch All
COMMAND_CLASS_SWITCH_ALL
Switch Color
COMMAND_CLASS_SWITCH_COLOR
Switch Multilevel V2
COMMAND_CLASS_SWITCH_MULTILEVEL_V2
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Exclusion
Remove for exclusion

1. Assuming led bulb was added to controller.

2. Triggered by OFF -> ON -> OFF -> ON -> OFF -> ON (between 0.5-2 seconds each time).

3. LED Solid Purple/Violet Color (0xEE82EE) during the unpairing process. (Timeout is 10 seconds).

 Failure:

Blinks between 100% White and Red 0x0000FF color for 3 seconds (at a rate of 200ms per flash), Once 3 seconds have passed, the LED should return to the last color ( memory status(color cc set)) of LED Bulb.

 Success:

Blinks between 100% White and Blue 0x0000FF color for 3 seconds (at a rate of 200ms per flash). Once 3 seconds have passed, the LED should return to a Warm White LED at 100%.

Factory Reset
Reset the Device.

1. Assuming led bulb was added to controller and was power on.

2. RGBW bulb re-power 6 times (between 0.5-2 seconds each time).

Note: ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON

3. If the 6th power on, the led bulb change to Yellow color(into pairing process ), which means that the reset factory settings are successf.



Using this action in case of the primary controller is missing or inoperable.

Inclusion
Add for inclusion

1. Ensure the led bulb has been excluded outside the network.

2. Triggered by OFF ->ON (between 0.5-2 seconds each time)

3. LED solid yellow Color (0xFFFF00) during the pairing(Timeout is 10 seconds).



 Failure:

Blinks between 100% White and Red 0x0000FF color for 3 seconds (at a rate of 200ms per flash), Once 3 seconds have passed, the LED should return to a Warm White LED at 100%

 Success:

Blinks between 100% White and Green 0x00FF00 color for 3 seconds (at a rate of 200ms per flash). Once 3 seconds have passed, the LED should return to a Warm White LED at 100%.

Color
If the product is only available in one color, pick the color from the list.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Switch Load Capacity Watts
The amount of switch load energy the product is rated for in Watts

 

Avaliações

Escrever uma avaliação

AEOTEC Bombilla LED 6 Multi-Color (E27)

AEOTEC Bombilla LED 6 Multi-Color (E27)

6 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: