Produtos visualizados





Confianza Online


POPP Sensor de inundación / agua Z-Wave+ View larger

POPP Inundação / sensor de água Z-Wave +

POPE700052

Novo

O sensor de inundação POPP protege contra inundações e vazamentos de água, notificando localmente e, por meio de um controlador Z-Wave, ele notifica o celular.

Mais detalhes

Em estoque

39,99 €

Características tecnicas

Tecnologia Z-Wave Plus

Mais Informação

Uma mangueira quebrada na máquina de lavar ou uma mangueira com vazamento na torneira pode causar sérios danos, mesmo se houver apenas um pequeno vazamento. O sensor de inundação POPP protege contra essas desvantagens. Assim que o dispositivo detecta água em suas sondas, um alarme sonoro é ativado. Além disso, o LED começa a piscar e o sinal de alarme é enviado para o controlador Z-Wave. Por esse motivo, você recebe uma mensagem em seu smartphone e pode agir imediatamente, mesmo quando não está em casa. Como resultado, você pode evitar danos significativos causados pelo vazamento de água.

Conectado a outros dispositivos inteligentes, como o motor de válvula de 1/4 de volta, ele pode até mesmo cortar a água automaticamente se houver vazamento em um cano de água e descartar um sistema automático de corte por inundação por um preço.

O sensor de inundação POPP pode ser colocado sob uma lavadora ou pia. Se não houver espaço suficiente para a unidade principal, você poderá usar o sensor com cabo fornecido com a placa de montagem adicional na parede. O sensor é resistente à água e flutua (classe de proteção IP44). Portanto, também é adequado para uso externo.

FUNÇÕES

Detector de inundação Z-Wave
Compatível com Z-Wave Plus
Alertas em caso de vazamento de água
Alarme acústico e óptico através de um LED
Fornecido com uma sonda de cabo externo
Resistente à água (IP44)

CARACTERÍSTICAS TECNICAS :

Tipo de módulo: transmissor de onda Z
Fonte de alimentação: bateria CR2 3V
Freqüência: 868,42 MHz
Distância de transmissão: 100 m em campo livre, 40 m no interior
Dimensões: 66 x 66 x 23 mm
Peso: 0,105 kg

Informação alargada da Z-Wave (Inglês)

Nome: Water Leakage Detector
Fabricante:Coolcam
Identificador:NAS-WS02ZU
Número de Certificação Z-Wave :ZC10-18076181
Plataforma de Hardware :ZM5202
FLiRS:Não
Tipo de Role :Reporting Sleeping Slave
Descrição breve :Water Leakage Detector is an intelligent security equipment that can transmit the Z-Wave network which has particular frequency. Different countries or areas, the radio frequency of Z-Wave is different.
Descrição :In the Z-Wave network communications, water sensor can work with any Z-Wave main controller. In the Z-Wave network communications, water sensor can send messages to the Z-Wave main controller, and realize association with other devices through the Z-Wave network. In the communication with the Z-Wave main controller, the water sensor can send messages to the Z-Wave main controller, but it can not receive messages from the Z-Wave main controller. When the water sensor is triggered, the LED light keeps on and the buzzer will make sound. The water sensor sends messages to the Z-Wave main controller at the same time, the Z-Wave main controller will display the current status of water sensor. Water sensor is battery powered, is small and can be installed easily.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
5
Group 1 is lifeline group; all nodes which associated in this group will receive the messages sent by device through lifeline. Command Class: COMMAND_CLASS_NOTIFICATION COMMAND_CLASS_SENSOR_BINARY COMMAND_CLASS_BATTERY COMMAND_CLASS_DEVICE_RESET_LOCALLY Event: NOTIFICATION_REPORT SENSOR_BINARY_REPORT BATTERY_REPORT DEVICE_RESET_LOCALLY_NOTIFICATION
2
5
Group 2 is controlling group, all nodes associated in this group will be controlled through BASIC_SET command by the device when device detects a water leakage event. Command Class: COMMAND_CLASS_BASIC Event: BASIC_SET
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
1
1
120
Alarm Duration Time
This configuration can be used to adjust the time for beep and LED turned on when water leakage is detected. If this configuration is set to ‘0’, the beep and LED will be turn on always until water leakage is not detected.
10
1
0
Battery Report Periodically Enable
This parameter sets to ‘1’ will enable reporting battery periodically. The period time is defined by configuration parameter 11. If this value set to ‘0’, battery report will be executed in two cases listed as below. 1, Device is power up. 2, Battery life is falling 100, 16 and 0
11
2
480
Battery Report Interval
This parameter is defined the interval time for battery report. This value is larger, the battery life is longer. Unit: Minute.
2
1
60
Alarm Interval Time
This configuration defines beep on /off interval time when water leakage is detected.
3
1
60
First Alarm On Time Duration
This configuration defines beep on duration first time when water leakage is detected.
4
1
5
Alarm on Time Duration
This configuration defines beep on duration after fist beep on when water leakage is detected.
5
1
1
Water Leakage Detected Disable
This configuration sets to ‘0’ will disable the water leakage detected function.
6
1
1
Beep Alarm Disable
This configuration sets to ‘0’ will disable the beep alarm on when device detects water leakage event.
7
1
1
Led Light Alarm Disable
This configuration sets to ‘0’ will disable the Led indicating when device detects a water leakage event.
8
1
100
Basic Set Level
This configuration sets the level for device sending BASIC_SET to nodes that associated in group 2 when device detects a water leakage event. [0] – Off, BASIC_SET = 0x00, all nodes associated in group 2 will be off. [1 … 99] – On. BASIC_SET = [Setting Value]. [100] – On, BASIC_SET = 0xFF.
Basic V2
COMMAND_CLASS_BASIC_V2
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Battery
COMMAND_CLASS_BATTERY
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Notification V8
COMMAND_CLASS_NOTIFICATION_V8
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S2
COMMAND_CLASS_SECURITY_2
Sensor Binary V2
COMMAND_CLASS_SENSOR_BINARY_V2
Supervision
COMMAND_CLASS_SUPERVISION
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V3
COMMAND_CLASS_VERSION_V3
Wake Up V2
COMMAND_CLASS_WAKE_UP_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Inclusion
1,Power up the device.

2, Set Z-Wave™ Controller into inclusion

mode

3, Press the button 3 times within 1s to

enter inclusion mode.

4,The device will be recognized and

automatically included into Z-Wave™

Network.
Exclusion
1, Power up the device.

2,Set Z-Wave™ Controller into exclusion

mode

3, Press the button 3 times within 1s to

enter exclusion mode
Device Wake-Up
Press the button briefly,Led will blink once.
Additional Special Features
Product Test Mode

1,Press and hold the button.

2,Power on the device, device will enter

factory product test mode
Factory Reset
1,Power up the device.

2, Press and hold the button for 10s until

led light is on, then release the button.

Please use this procedure only when the network primary controller is missing or otherwise inoperable
S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Color
If the product is only available in one color, pick the color from the list.
Communications Connections
Connectivity for communications with a host control computer or system.
Controller Supports Multiple Networks
Indicates support for the controller to manage multiple Z-Wave networks concurrently.
Controller Supports Multiple Z-Wave Interfaces
Indicates support for multiple Z-Wave interfaces managed by a single host controller system. Allows for Z-Wave signals to be sent from multiple controllers in the same network or to manage several Z-Wave networks.
Gateway Has Preferred Partners
The gateway may provide less robust support to non-preferred brands of products when they are added to the network that the gateway controls.
Sensors
Sensor types supported by the product.
Battery Quantity
Enter the number of batteries of the designated type that the product uses.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.

 

Avaliações

Escrever uma avaliação

POPP Inundação / sensor de água Z-Wave +

POPP Inundação / sensor de água Z-Wave +

O sensor de inundação POPP protege contra inundações e vazamentos de água, notificando localmente e, por meio de um controlador Z-Wave, ele notifica o celular.

Accessories

5 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: