Produtos visualizados





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

Qubino Flush Dimmer 0-10V

ZMNHVD1

Novo

Iluminação inteligente (iluminação smarthome) e regulação LED (dimmer). Módulo de regulação universal (dimmer) com uma saída padrão de 0-10V e uma entrada multifunção, que pode ser um botão, interruptor, potenciômetro ou um sinal de 0 a 10 volts (0-10V)

Mais detalhes

Em estoque

64,32 €

-12%

73,10 €

Características tecnicas

Tecnologia Z-Wave Plus
Recurso Dimmer

Mais Informação

Qubino Flush Dimmer 0-10V: o único dimmer ou dimmer 0-10V Z-Wave universal

O Qubino Flush Dimmer 0-10V é um dimmer universal com uma saída padrão de 0-10V e uma entrada multifunção, que pode ser um botão ou comutador, um potenciômetro ou um sinal de 0-10V. Também mede o consumo de energia e suporta a conexão de um sensor de temperatura digital.

Usado para?

O Qubino Flush Dimmer 0-10V é ideal para regulagem de luzes LED por controle remoto e automação residencial para sistemas de iluminação com reator de baixa tensão.

O Qubino Flush Dimmer 0-10V é um produto Z-Wave Plus atualmente ÚNICO e exclusivo de seu tipo . Ele foi pesquisado e desenvolvido com base em usuários e entusiastas do DIY que buscavam desesperadamente uma solução Z-Wave com uma entrada / saída de 0-10V. O Qubino Flush Dimmer 0-10V resultou no dimmer perfeito para iluminação LED.

O menor dimmer de onda Z

O módulo Z-Wave Qubino Flush Dimmer 0-10V é um micromódulo que ocupa menos espaço do que qualquer outro módulo com o qual é comparado a qualquer outro concorrente e se encaixa facilmente em qualquer caixa de mecanismo convencional.

Qubino Flush Dimmer 0-10

Controle de energia

O dimmer Z-Wave Qubino Flush Dimmer 0-10V , mede o consumo elétrico do dispositivo elétrico conectado e, por si só, quando está em "standby" consome apenas 0,5 W.

Muito versátil

O Qubino Flush Dimmer 0-10V pode operar através de uma extensa faixa de temperaturas, de frio -10º C a sufocante 40º C (14º a 104ºF). Ele suporta a conexão de um sensor de temperatura digital, que também é útil para criar cenários complexos. Cada módulo também atua como um repetidor para melhorar o alcance e a estabilidade da rede Z-Wave.

A instalação mais simples

O tamanho extremamente pequeno e uma caixa especialmente projetada significam que a conexão do módulo dentro de uma caixa de montagem embutida é simples. O processo de instalação, testado e aprovado por eletricistas profissionais , consiste em apenas três etapas simples:

1 - Remova os interruptores da caixa e desconecte os cabos.
2 - Conecte os cabos ao módulo Qubino e insira-os na caixa.
3 - Fixe os interruptores na caixa.

Os módulos Z-Wave mais comprovados e confiáveis

Os módulos Z-Wave da Qubino são produtos de instalação e esquecimento. Os produtos Qubino que oferecemos, são fabricados para durar, então eles só usam componentes eletrônicos que atendem aos mais exigentes níveis de qualidade. Nossos módulos são também os micromódulos Z-Wave mais testados no mercado. O Instituto Esloveno de Qualidade e Medição (SIQ), uma entidade europeia independente, verifica a qualidade dos parâmetros reais de nossos produtos, incluindo aumentos de temperatura, fabricação, resistência de isolamento, consumo elétrico e sobrecargas de acordo com os padrões europeus da mais alta qualidade de acordo com a especificação da norma EN 60669-2-1.

Parâmetros adicionais para profissionais.

O micromodulo Qubino Flush Dimmer 0-10V   Possui 25 parâmetros adicionais para seu uso por especialistas. Alguns dos mais úteis são:

  • Permite o ajuste de entrada com base no tipo de dispositivo (interruptor, potenciômetro, sensor 0-10V, etc.)
  • Saída on / off automática após o tempo definido

O micromodulo Qubino Flush Dimmer 0-10V pode ser controlado através de uma rede Z-Wave e através de um interruptor de parede. Este módulo foi projetado para ser montado dentro de uma caixa de mecanismo e escondido atrás de um interruptor de parede convencional.

Especificações técnicas e diagramas elétricos:

Qubino Flush Dimmer 0-10

Comida: 12 24 VDC

Max. Tensão de controle de "afundamento"

-20 / +20 VDC
Tensão máxima de controle de fornecimento 0 11 VDC
Max. naufrágio atual 2 mA
Max. corrente de fornecimento 7 mA
Precisão da medição de potência: <3% FS
Faixa do sensor de temperatura digital: -50 ° ~ + 125 ° C, resolução de 0,1 ° C
Comprimento do cabo do sensor de temperatura digital: 1000 mm
Temperatura de funcionamento: -10 ° ~ + 40 ° C
Distância até 30 m dentro de casa (dependendo dos materiais)
Dimensões (LxAxP) 41,8 x 36,8 x 15,4 mm
(embalagem) (115 x 96 x 22)
Peso (incluindo embalagem) 28 g (34 g)
Consumo elétrico em standby 0,5 W
Para instalação em caixas de mecanismo Ø e 60 mm ou 2 M

Atende às certificações CE e ROHS

Download

Informação alargada da Z-Wave (Inglês)

Nome: Qubino Flush Dimmer 0-10V
Fabricante:QUBINO
Identificador:ZMNHVD1
Número de Certificação Z-Wave :ZC10-17025424
Plataforma de Hardware :ZM5202
FLiRS:Não
Tipo de Role :Always On Slave
Descrição breve :The Qubino Flush Dimmer 0-10V is ideal for remotely dimming LED lights with low voltage ballast.
Descrição :The Qubino Flush Dimmer 0-10V is a universal dimmer with a standard 0-10V output and a multi-function input, which may be a push button or switch, a potentiometer or a 0-10V signal. It also measures power consumption and supports the connection of a digital temperature sensor.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
1
Z-Wave Plus Lifeline
2
16
Basic On/Off
3
16
Start Level Change/Stop Level Change
4
16
Multilevel Set
5
16
Multilevel Sensor Report (triggered at change of analogue sensor)
6
16
Multilevel Sensor Report (triggered at change of temperature sensor)
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
1
1
0
Input 1 switch type
By this parameter the user can set input based on device type (switch, potentiometer, 0-10V sensor,..). NOTE: After parameter change to value 3, 4 or 5 first exclude module (without setting parameters to default value) then wait at least 30s and then re include the module!
10
2
255
Activate / deactivate functions ALL ON / ALL OFF
Flush Dimmer 0-10V module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.
11
2
0
Automatic turning off output after set time
Turns off the output after set time.
110
2
32536
Temperature sensor offset settings
Set value is added or subtracted to actual measured value by sensor.
12
2
0
Automatic turning on output after set time
Turns on the output after set time.
120
1
5
Digital temperature sensor reporting
Digital temperature sensor reporting If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter. Available configuration parameters (data type is 1 Byte DEC): • default value 5 = 0,5°C change • 0 - Reporting disabled • 1 - 127 = 0,1°C - 12,7°C, step is 0,1°C
140
2
5
Input I1 Sensor reporting
Input I1 Sensor reporting If analogue sensor is connected, module reports measured value on change defined by this parameter.
141
1
5
Input I1 0-10V reporting threshold
Parameter is associated with Association group No. 2. Below this value, the Association No. 2 will report Basic Set 0xFF and above this value will report Basic Set 0xFF. Basic Set is reported only, when the input value changes for more than 10% (1V).
143
2
0
Minimum sensor range value
Value that must correspond to minimum sensor range value. Valid only if parameter 1 is set to values 3, 4 or 5). Available configuration parameters (data type is 2 Byte DEC): • default value 0 = 0.0°C / 0Lux / 0.0%rh • 0 - 10000 – value from 0 to 1000 (resolution 0,1) • 10001 – 20000 – value from -0,1 to -1000 (resolution 0,1) NOTE: Minimum value must not be higher than maximum value!
144
2
1000
Maximum sensor range value
Value that must correspond to maximum sensor range value. Valid only if parameter 1 is set to values 3, 4 or 5). NOTE: Maximum value must not be lower than minimum value!
21
1
0
Enable/Disable Double click function
If Double click function is enabled, a fast double click on the push button will set dimming power at maximum dimming value. Valid only if input is set as mono-stable (push button).
250
1
0
Unsecure / Secure Inclusion
A Flush dimmer supports secure and unsecure inclusion. Even if the controller does not support security command classes, a dimmer could be included as unsecure and keep all the functionality.
30
1
0
Saving the state of the device after a power failure
Based on the parameter settings the stores/does not store the last value of the output after power failure.
52
1
0
Auto or manual selection
This parameter is influencing on the software only when the value of parameter number 1 is set to value 3, 4 or 5. In manual mode regulation (how the input influence on output) is disabled.
53
1
0
PID value inside deadband
NOTE: When ZERO PID inside deadband is forced to zero. LASTVALUE means that PID remains on same level as was before entering into deadband.
54
1
1
PID deadband
NOTE: This parameter defines the zone where PID is not active. If the temperature difference between actual and setpoint is bigger than PID deadband, then the PID will start to regulate the system, otherwise the PID is zero or fixed.
55
1
5
Integral sampling time
Parameter defines the time between samples. On each sample the controller capture difference between SP-act.
56
2
100
P parameter
The error is multiplied by a negative (for reverse action) proportional constant P, and added to the current output. P represents the band over which a controller's output is proportional to the error of the system. E.g. for a heater, a controller with a proportional band of 10 deg C and a setpoint of 100 deg C would have an output of 100% up to 90 deg C, 50% at 95 Deg C and 10% at 99 deg C. If the temperature overshoots the setpoint value, the heating power would be cut back further. Proportional only control can provide a stable process temperature but there will always be an error between the required setpoint and the actual process temperature.
57
2
1
I parameter
The error is integrated (averaged) over a period of time, and then multiplied by a constant I, and added to the current control output. I represents the steady state error of the system and will remove setpoint / measured value errors. For many applications Proportional + Integral control will be satisfactory with good stability and at the desired setpoint.
58
2
1
D parameter
The rate of change of the error is calculated with respect to time, multiplied by another constant D, and added to the output. The derivative term is used to determine a controller's response to a change or disturbance of the process temperature (e.g. opening an oven door). The larger the derivative term, the more rapidly the controller will respond to changes in the process value.
60
1
1
Minimum dimming value
NOTE: The minimum level may not be higher than the maximum level! 1% min. dimming value is defined by Z-Wave multilevel device class. When the switch type is selected as Bi-stable, it is not possible to dim the value between min and max. If Switch_multilevel_set is set to the value “0”, the output is turned OFF. If Switch_multilevel_set is set to the value “1”, the output is set to the minimum diming value.
61
1
99
Maximum dimming value
NOTE: The maximum level may not be lower than the minimum level! 99% max. dimming value is defined by Z-Wave multilevel device class. When the switch type is selected as Bi-stable, it is not possible to dim the value between min and max.
65
2
100
Dimming time (soft on/off)
Set value means time of moving the Flush Dimmer 0-10V between min. and max. dimming values by short press of push button I1 or controlled through UI (BasicSet).
66
2
3
Dimming time when key pressed
Time of moving the Flush Dimmer 0-10V between min. and max dimming values by continues hold of push button I1 or associated device.
67
1
0
Ignore start level
This parameter is used with association group 3. A receiving device SHOULD respect the start level if the Ignore Start Level bit is 0. A receiving device MUST ignore the start level if the Ignore Start Level bit is 1.
68
1
0
Dimming duration
This parameter is used with association group 3. The Duration field MUST specify the time that the transition should take from the current value to the new target value. A supporting device SHOULD respect the specified Duration value.
Basic
COMMAND_CLASS_BASIC
Switch Multilevel V3
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Association Group Information V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Sensor Multilevel V7
COMMAND_CLASS_SENSOR_MULTILEVEL_V7
Switch All
COMMAND_CLASS_SWITCH_ALL
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Switch Multilevel V3
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Exclusion
• Connect module to power supply

• bring module within maximum 1 meter (3 feet) of the main controller,

• enable add/remove mode on main controller,

• press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or

• press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second.

By this function all parameters of the module are set to default values and own ID is deleted.

If push button I1 is pressed three times within 3s (or service button S is pressed more than 2 and less than 6 seconds) module is excluded, but configuration parameters are not set to default values.



NOTE 1: If the module is included with parameter 1 value 3, 4 or 5 and module reset is done, wait at least 30s before next inclusion.



NOTE 2: Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Factory Reset
• Press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or

• press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second.



Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Inclusion
• Connect module to power supply (with

temperature sensor connected - if purchased),

• enable add/remove mode on main controller

• auto-inclusion (works for about 5 seconds after connected to power supply) or

• press service button S for more than 2 second or

• press push button I1 three times within 3s (3 times change switch state within 3 seconds).



NOTE1: For auto-inclusion procedure, first set main controller into inclusion mode and then connect module to power supply.

NOTE2: When connecting temperature sensor to module that has already been included, you have to exclude module first. Switch off power supply, connect the sensor and re-include the module.

Color
If the product is only available in one color, pick the color from the list.
Sensors
Sensor types supported by the product.
Switch Type
Describes the type of operator for a switch.
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps

 

Avaliações

Escrever uma avaliação

Qubino Flush Dimmer 0-10V

Qubino Flush Dimmer 0-10V

Iluminação inteligente (iluminação smarthome) e regulação LED (dimmer). Módulo de regulação universal (dimmer) com uma saída padrão de 0-10V e uma entrada multifunção, que pode ser um botão, interruptor, potenciômetro ou um sinal de 0 a 10 volts (0-10V)

Accessories

30 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: