Produtos visualizados





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

QUBINO DIN Dimmer para calha Z-Wave Plus

ZMNHSD1

Novo

Módulo regulador ou dimmer Z-Wave + QUBINO DIN Dimmer para montagem em painel elétrico por trilho DIN com medição de consumo.

Mais detalhes

Em estoque

80,52 €

-12%

91,50 €

Características tecnicas

Tecnologia Z-Wave Plus
Recurso Dimmer

Mais Informação

Qubino DIN Dimmer: Primeiro regulador de onda Z para trilho, verdadeiramente universal

O controlador Z-Wave, Qubino DIN Dimmer é um dimmer para instalação em trilho DIN para lâmpadas ou ventiladores. Você pode controlá-lo remotamente através da rede Z-Wave ou através de interruptores de parede.

Usado para?

O Qubino DIN Dimmer é um dimmer montado em trilho DIN, ideal para controlar e medir remotamente o consumo de energia de lâmpadas ou ventiladores. Também suporta a conexão de um sensor de temperatura digital.

O menor dimmer de trilho DIN Z-Wave

O dimmer Z-Wave Qubino DIN Dimmer é um módulo para trilho DIN que ocupa menos espaço do que qualquer outro módulo para caixa com o qual é comparado a qualquer outro concorrente e cabe facilmente em menos espaço do que parece em uma caixa elétrica com trilho DIN .

Dimmer din Qubino

Controle de energia

O dimmer Z-Wave Qubino DIN Dimmer , mede o consumo elétrico do dispositivo elétrico conectado e, por si só, quando está em "standby" consome apenas 0,7 W.

Muito versátil

O Qubino DIN Dimmer , pode operar através de uma ampla faixa de temperaturas, de -10ÚC frio a 40UF (14Ú10) de sufocamento. Ele suporta a conexão de um sensor de temperatura digital, que também é útil para criar cenários complexos. Cada módulo também atua como um repetidor para melhorar o alcance e a estabilidade da rede Z-Wave.

A instalação mais simples

O módulo Qubino DIN Dimmer ocupa um volume menor do que os módulos comparáveis de qualquer outra marca e cabe facilmente em qualquer trilho DIN. O processo de instalação, testado e aprovado por eletricistas profissionais , é tão fácil e conveniente quanto qualquer outro módulo ferroviário.

Instalação Dimmer DIN Qubino

Os módulos Z-Wave mais comprovados e confiáveis

Os módulos Z-Wave da Qubino são produtos de instalação e esquecimento. Os produtos Qubino que oferecemos, são fabricados para durar, então eles só usam componentes eletrônicos que atendem aos mais exigentes níveis de qualidade. Nossos módulos são também os micromódulos Z-Wave mais testados no mercado. O Instituto Esloveno de Qualidade e Medição (SIQ), uma entidade europeia independente, verifica a qualidade dos parâmetros reais de nossos produtos, incluindo aumentos de temperatura, fabricação, resistência de isolamento, consumo elétrico e sobrecargas de acordo com os padrões europeus da mais alta qualidade de acordo com a especificação da norma EN 60669-2-1.

Parâmetros adicionais para profissionais

O módulo Qubino DIN Dimmer   Possui 17 parâmetros adicionais para seu uso por especialistas. Alguns dos mais úteis são:

  • Saída on / off automática após o tempo definido
  • Alterar entre o tipo de entrada normalmente aberto e normalmente fechado
  • Salve o estado do dispositivo após um corte de energia

Este módulo Z-Wave é usado para controlar e regular as lâmpadas ou para controlar a velocidade de um ventilador. Ele pode ser controlado sem fio (sem fios) através da rede Z-Wave ou através de um interruptor de parede conectado a ela.
O módulo foi projetado para ser montado dentro de um gabinete ou rack elétrico em um trilho DIN. Também mede o consumo de energia das cargas conectadas. Ele também tem uma entrada para a conexão de um sensor de temperatura que pode ser adquirido separadamente.
O Qubino DIN Dimmer também foi projetado para funcionar como um repetidor para melhorar o alcance e a estabilidade da rede Z-Wave.
Finalmente, deve-se notar que a marca QUBINO estabeleceu fortes compromissos em qualidade e sustentabilidade: os componentes de alta performance foram cuidadosamente selecionados. Vários testes de controle de qualidade também foram realizados no módulo para garantir a máxima durabilidade (resistente o suficiente para operar em temperaturas de -10 ° C a +40 ° C).

Esquema de conexão para 220AC e 24V DC

Diagrama de conexão dimmer para trilho DINQubino din dimmer diagrama elétrico

FUNÇÕES


Controlar e regular a iluminação remota ou outros dispositivos suscetíveis de regulação
Ele é colocado em direção ao painel elétrico, instalado no trilho DIN
Habilita ON / OFF / DIM
Utiliza tecnologia MOSFET: compatível com lâmpadas halógenas de baixa tensão com transformador eletrônico, lâmpadas fluorescentes compactas dimerizáveis e LEDs dimerizáveis
Integra a série de 500 chips (Z-Wave +)
Comunicação 250% mais rápida em comparação com dispositivos Z-Wave padrão
A primeira unidade de trilho DIN Z-Wave do mundo
Consumo de energia muito baixo de até 0.7W
Temperatura de operação -10 a 40 ° C
Conector do sensor de temperatura analógica
Integra medição de consumo de energia

CARACTERÍSTICAS TECNICAS:

Comida: 110 230 VAC ± 10%
50/60 Hz, (24 30 VDC)

Carga máxima de saída CA (carga resistiva) *

0,85 A / 230 VAC
Carga máxima de saída DC (carga resistiva) * 0,85 A / 30 VCC
Potência do circuito de saída da saída AC (carga resistiva): 200 W (230 VAC)
Potência do circuito de saída da saída DC (carga resistiva): 21 W (24 VDC)
Precisão da medição de potência: +/- 2 W
Faixa do sensor de temperatura digital: -50 ° ~ + 125 ° C, resolução de 0,1 ° C
Comprimento do cabo do sensor de temperatura digital: 1000 mm
Temperatura de funcionamento: -10 ° ~ + 40 ° C
Distância até 30 m dentro de casa (dependendo dos materiais)
Dimensões (LxAxP) 18 x 93 x 58 mm
(embalagem) (21 x 95 x 64 mm)
Peso (incluindo embalagem) 50 g (56 g)
Consumo elétrico em standby 0,7 W
Assembly Trilho DIN
Comutação por: MOSFET (borda de fuga)



Atende às certificações CE e ROHS

Download

Informação alargada da Z-Wave (Inglês)

Nome: DIN Dimmer
Fabricante:QUBINO
Identificador:ZMNHSD1
Número de Certificação Z-Wave :ZC10-17035480
Plataforma de Hardware :ZM5202
FLiRS:Não
Tipo de Role :Always On Slave
Descrição breve :DIN Dimmer is a DIN rail mounted dimmer for light bulbs. You can control it either remotely through the Z-Wave network or through wall switches. It also measures power consumption and supports the connection of a digital temperature sensor.
Descrição :DIN Dimmer is a DIN rail mounted dimmer for light bulbs. You can control it either remotely through the Z-Wave network or through wall switches. It also measures power consumption and supports the connection of a digital temperature sensor.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
1
Lifeline group (reserved for communication with the main controller)
2
16
Basic on/off (triggered at change of the input I1 state and reflecting its state)
3
16
Start level change/stop level change (triggered at change of the input I1 state and reflecting its state)
4
16
Multilevel set (triggered at changes of state/value of the DIN Dimmer)
5
16
Multilevel sensor report (triggered at change of temperature sensor)
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
1
1
0
Input switch type
Available configuration parameters (data type is 1 Byte DEC): • default value 0 • 0 - mono-stable switch type (push button) • 1 - bi-stable switch type
10
2
255
Activate / deactivate functions ALL ON / ALL OFF
DIN Dimmer module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.
11
2
0
Automatic turning off output after set time
Turns off the output after set time.
110
2
32536
Temperature sensor offset settings
Set value is added or subtracted to actual measured value by sensor. Available configuration parameters (data type is 2 Byte DEC): • default value = 32536 • 32536 = offset is 0.0C • 1 - 100 = value from 0.1 °C to 10.0 °C is added to actual measured temperature. • 1001 - 1100 = value from -0.1 °C to -10.0 °C is subtracted to actual measured temperature.
12
2
0
Automatic turning on output after set time
Turns on the output after set time.
120
1
5
Digital temperature sensor reporting
Digital temperature sensor reporting If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter. Available configuration parameters (data type is 1 Byte DEC): • default value 5 = 0,5°C change • 0 = reporting disabled • 1- 127 = 0,1°C - 12,7°C, step is 0,1°C
21
1
0
Enable/Disable Double click function
If Double click function is enabled, a fast double click on the push button will set dimming power at maximum dimming value.
30
1
0
Saving the state of the device after a power failure
Based on the parameter settings the stores/does not store the last value of the output after power failure.
40
1
5
Power reporting in Watts on power change
Set value means percentage, set value from 0 - 100=0% - 100%. Power report is send (push) only when actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%. NOTE: if power changed is less than 1W, the report is not send (pushed), independent of percentage set.
42
2
0
Power reporting in Watts by time interval
Set value means time interval (0 – 32767) in seconds, when power report is send. Reporting enabled. Power report is send with time interval set by entered value. Please note, that too fast reporting can cause too much Z-Wave traffic resulting in Z-Wave poor response.
5
1
0
Working mode
With this parameter is possible to change the module presentation on the user interface NOTE: After parameter change, first exclude module (without setting parameters to default value) then wait at least 30s and then re include the module!
60
1
1
Minimum dimming value
The minimum level may not be higher than the maximum level! 1% min. dimming value is defined by Z-Wave multilevel device class. When the switch type is selected as Bi-stable, it is not possible to dim the value between min and max. If Switch_multilevel_set is set to the value “0”, the output is turned OFF. If Switch_multilevel_set is set to the value “1”, the output is set to the minimum diming value.
61
1
99
Maximum dimming value
The maximum level may not be lower than the minimum level! 99% max. dimming value is defined by Z-Wave multilevel device class. When the switch type is selected as Bi-stable, it is not possible to dim the value between min and max.
65
2
100
Dimming time (soft on/off)
Set value means time of moving the DIN Dimmer between min. and max. dimming values by short press of push button I or controlled through UI (BasicSet).
66
2
3
Dimming time when key pressed
Time of moving the DIN Dimmer between min. and max dimming values by continues hold of push button I or associated device.
67
1
0
Ignore start level
This parameter is used with association group 3.A receiving device SHOULD respect the start level if the Ignore Start Level bit is 0. A receiving device MUST ignore the start level if the Ignore Start Level bit is 1.
68
1
0
Dimming duration
This parameter is used with association group 3. The Duration field MUST specify the time that the transition should take from the current value to the new target value. A supporting device SHOULD respect the specified Duration value.
Basic
COMMAND_CLASS_BASIC
Switch Multilevel V3
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Association Group Information V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V4
COMMAND_CLASS_METER_V4
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Sensor Multilevel V7
COMMAND_CLASS_SENSOR_MULTILEVEL_V7
Switch All
COMMAND_CLASS_SWITCH_ALL
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Switch Multilevel V3
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Exclusion
• Connect module to power supply

• bring module within maximum 1 meter (3 feet) of the main controller,

• enable add/remove mode on main controller,

• press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or

• press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second.

By this function all parameters of the module are set to default values and own ID is deleted.

If push button I1 is pressed three times within 3s (or service button S is pressed more than 2 and less than 6 seconds) module is excluded, but configuration parameters are not set to default values.



NOTE 1: If the module is included with parameter 1 value 3, 4 or 5 and module reset is done, wait at least 30s before next inclusion.



NOTE 2: Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Inclusion
• Connect module to power supply (with

temperature sensor connected - if purchased),

• enable add/remove mode on main controller

• auto-inclusion (works for about 5 seconds after connected to power supply) or

• press service button S for more than 2 second or

• press push button I1 three times within 3s (3 times change switch state within 3 seconds).



NOTE1: For auto-inclusion procedure, first set main controller into inclusion mode and then connect module to power supply.

NOTE2: When connecting temperature sensor to module that has already been included, you have to exclude module first. Switch off power supply, connect the sensor and re-include the module.

Factory Reset
• Press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or

• press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second.



Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Switch Type
Describes the type of operator for a switch.
Color
If the product is only available in one color, pick the color from the list.
Sensors
Sensor types supported by the product.

 

Avaliações

Escrever uma avaliação

QUBINO DIN Dimmer para calha Z-Wave Plus

QUBINO DIN Dimmer para calha Z-Wave Plus

Módulo regulador ou dimmer Z-Wave + QUBINO DIN Dimmer para montagem em painel elétrico por trilho DIN com medição de consumo.

Accessories

30 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: