Servo de válvula de esfera Aqua-Scope - Motor para operar válvulas de esfera

Características tecnicas

Tecnologia	Z-Wave Serie 700

Mais Informação

O BVS (Ball Valve Servo) com Z-Wave é um motor para reequipamento de válvulas de esfera existentes e instaladas em dispositivos inteligentes de controle de água. O motor é alimentado por uma fonte de alimentação externa de 12 V.

As braçadeiras variáveis permitem a montagem mesmo em instalações de tubos complexas. O acoplamento de motor patenteado garante fácil instalação e operação precisa de longo prazo. O dispositivo pode operar em condições ambientais difíceis, mesmo submerso em água, e permite que uma almofada de sensor de água local adicional seja conectada diretamente por cabo.

Controle remoto: controle sua válvula principal de água ou gás remotamente, quando tiver sua válvula de esfera servo conectada a um gateway Z-Wave.

Simples, sem ferramentas: basta encaixar e girar 2 botões. Feito em menos de um minuto!

À prova de cotovelos: pode ser instalado nos cotovelos dos tubos pela posição das braçadeiras ajustáveis.

Controle de torque adaptável inteligente: Protege o motor, a válvula e a tubulação para operação de longo prazo.

Prova ao ar livre: classificação IP67, funciona mesmo submerso em água.

Detecção de congelamento embutida e sonda de detecção de água. Funciona offline também.

Caracteristicas:

Fonte de energia. Fonte de alimentação externa 12V / 1A (incluída)
Simples, sem ferramentas: basta encaixar e girar 2 botões. Feito em menos de um minuto!
À prova de cotovelos: pode ser instalado em cotovelos de tubos usando braçadeiras de posição ajustáveis
Controle de torque adaptável inteligente: Protege motor, válvula e tubulação para operação de longo prazo
Prova externa: com classificação IP67, funciona mesmo submerso em água
Instalação: válvulas de ½ polegada a 1 ¼ polegada
Detecção de congelamento embutida e sonda de detecção de água. Funciona offline também.
Tamanho da braçadeira: 64-124 mm ajustável
Força máxima de atuação: 6 Nm
Controle da válvula: Totalmente aberto / fechado, qualquer posição intermediária até 1% de passo
Protocolo: Z-Wave 700 Series
Temperatura de operação: - 30 ° C - 80 ° C

Dimensões do item (L x A x C) 145 x 130 x 60 mm
Dimensões da embalagem (LxAxL) 236 x 179 x 114 mm
Peso líquido do artigo 0,801 Kg
Peso bruto do artigo 1.147 Kg
Z-Wave Plus
Z-Wave S2
WEEE
CE
Grau de proteção IP67

Informação alargada da Z-Wave (Inglês)

Nome: Custos Ball Valve Servo

Fabricante:Custos

Identificador:BVSZWE

Número de Certificação Z-Wave :ZC12-21020179

Plataforma de Hardware :ZGM130

FLiRS:Não

Tipo de Role :Always On Slave

Descrição breve :Custos Ball Valve Servo (BVS) is the most advance retrofit valve controller for real DIY

Descrição :With patented mechanic design, Custos BVS can be installed by yourself on existing valve of your water main within 20 seconds without any tool, to provide fully automated shutoff against flooding. A super strong and advance mechanic combined with smart software algorithm allows the BVS to deal with even the toughest valve without compromising the integrity of your valve over the time. Key features: 1. Hassle free bare hand install in 20 seconds 2. Outdoor proof, can be deployed on water main outside your house 3. Build-in local leak detection probe, can work standalone 4. Elbow friendly, adjustable clamp span can fit in smallest space or oversized valve up to 1.25 inches 5. Smart adaptive torque control and self calibration, real plug and play without any hassle for adjustment or calibration.

Descarregue o manual a partir de aqui.

Grupo

Nodos máximos

Descrição

1

5

Lifeline Group - Device Reset Locally Notification - Basic Report - Binary Switch Report - Indicator Report - Sensor Multilevel Report – Temperature “Auto report based on Configuration Parameter 0x22 Setting.” - Heat Alarm Notification Report (0x04) - 0x00 = State idle - 0x02 = Overheat – no location support - - 0x06 = Underheat – no location support - Water Alarm Notification Report (0x05) - 0x00 = State idle - 0x02 = Water leak detected – no location support - Water Valve Notification Report (0x0F) - 0x01 = Valve operation - 0x00 = VALVE CLOSED/OFF (Valve does not let the water run through.) - 0x01 = VALVE OPEN/ON (Valve lets the water run through)

2

5

- Basic Set (By default the Configuration CC parameter 0x11 (17) “Inverse Water Valve report” is enabled to send out following report.) - 0x00 = Let the water run through (Based on Configuration Parameter 0x13) - 0xFF = Doesn’t let the water run through. (Based on Configuration Parameter 0x12) - 0x00 = Let the water run through (Based on Configuration Parameter 0x13) - 0xFF = Doesn’t let the water run through. (Based on Configuration Parameter 0x12)

3

5

- Basic Set - 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x32 Setting) - 0xFF = TRIGGERED (Based on Configuration Parameter 0x31 Setting)

4

5

- Basic Set - 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x27 Setting) - 0xFF = TRIGGERED (Based on Configuration Parameter 0x26 Setting)

5

- Basic Set - 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x2C Setting) - 0xFF = TRIGGERED (Based on Configuration Parameter 0x2B Setting)

Número

Tamanho (Bytes)

Valor por defeito

Nome

Descrição

17

1

Inverse Water Valve Report

Inverses Switch Binary Report when Water Valve = 0x00 “Valve doesn’t let the water run through in Notification and real physical status.”

18

1

Association Group 2 SET Value

Configure Association Group 2 Basic Set value when Binary Switch Report = 0xFF *(Related to Configuration setting 0x11)

19

1

2

Association Group 2 SET Value

Configure Association Group 2 Basic Set value when Binary Switch Report = 0x00 *(Related to Configuration setting 0x11)

33

1

Temperature Report Unit

Configure Temperature Unit report. The default Unit is depended on Regional Frequency Setting. (By default, US=°F and EU=°C)

34

2

260

Temperature Threshold Change

Configure Temperature threshold changed and send auto report

35

2

256

Temperature Report Offset

Configure Temperature Offset degree; Higher byte 0x = Positive degree and 1x= Negative degree.

36

2

360

Overheat Trigger Value

Configure Overheat report trigger value. “Higher byte 0x00 represents Celsius °C unit, 0x01 represents Fahrenheit °F unit

37

2

342

Overheat Recover value

Configure Overheat Recover report value

38

1

0

Association Group 4 Overheat Trigger

Configure Overheat Trigger Value in Association Group 4

39

1

0

Association Group 4 Overheat Cancel

Configure Overheat Cancellation SET value

40

2

288

Freeze Trigger Value

Configure Freeze Trigger Report value

41

2

292

Freeze Recover Value

Configure Freeze Recover Report Value

42

1

Freeze Detection Valve Control

Enable / Disable Valve Control during Freeze when Water Leak is detected “Detected by built-in temperature sensor. Refer to Configuration CC parameter 0x28 (41) & 0x29 (42)

43

1

0

Association Group 5 Freeze Trigger

Configure Association Group 5 Freeze Detection Trigger Basic Set value

44

1

0

Association Group 5 Freeze Cancel

Configure Association Group 5 Freeze Detection Cancellation Basic Set value

49

1

Association Group 3 Water Leak Trigger

Configure Association Group 3 Water Leak Trigger Basic Set value

50

1

0

Association Group 3 Water Leak Cancel

Configure Association Group Water Leak Cancellation Basic Set value

51

1

Water Leak Detection Valve Control

Disable / Enable Valve Control when Water Leak detected

65

1

Buzzer

Enable / Disable Built-in Buzzer Sound

66

1

80

LED Brightness Level

Configure Built-in LED Brightness Level

67

1

0

Touch Keylock Protection

Disable / Enable Touch Keylock Protection

81

1

13

Notification Report

Configure Notification Report in Association Group 1 Lifeline “Set Bit to 0 = Disable, Set Bit to 1 = Enable” Default value 0x0D (13) Only available values as below xxxx xxx0 = Disable to report valve Open / Close status xxxx xxx1 = Enable to report valve Open / Close status (Default) xxxx xx0x = Disable Overheat Detection (Default) xxxx xx1x = Enable Overheat Detection xxxx x0xx = Disable Freeze (Underheat) Detection xxxx x1xx = Enable Freeze (Underheat) Detection (Default) xxxx 0xxx = Disable Water Leak Detection xxxx 1xxx = Enable Water Leak Detection (Default)

Application Status

COMMAND_CLASS_APPLICATION_STATUS

Association Group Information V3

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association V3

COMMAND_CLASS_ASSOCIATION_V3

Basic V2

COMMAND_CLASS_BASIC_V2

Configuration V4

COMMAND_CLASS_CONFIGURATION_V4

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Indicator V3

COMMAND_CLASS_INDICATOR_V3

Manufacturer Specific

COMMAND_CLASS_MANUFACTURER_SPECIFIC

Multi-Channel Association V4

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V4

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S0

COMMAND_CLASS_SECURITY

Security S2

COMMAND_CLASS_SECURITY_2

Sensor Multilevel V11

COMMAND_CLASS_SENSOR_MULTILEVEL_V11

Supervision

COMMAND_CLASS_SUPERVISION

Switch Binary V2

COMMAND_CLASS_SWITCH_BINARY_V2

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Factory Reset Procedure

Factory Default Reset:

To remove Custos BVS without involve gateway in Exclusion / Remove device operation and BVS will reset all setting to Factory Default

Setting.

i. Start: Long hold Touch Sense Button for 10 seconds then short click 5 times.

ii. Processing: Yellow LED ON 1 second then wait 2-5 seconds.

iii. Success: Green LED on 2 second with long beep sounds for 2 seconds.

*Factory Default Reset will:

a. Remote the BVS from Z-Wave Network;

b. Delete the association setting;

c. Restore the configuration settings to the default.

Classic Exclusion

Remove Custos BVS from Z-Wave Network:

Set your Z-Wave Gateway into Exclusion mode / Remove device.

i. Start: Short press Touch Sense Button 3 times.

ii. Processing: Yellow LED and short beep sound keeping continue.

iii. Success: Green LED on 1 second with 2 short beep sounds.

iv. The LED indication Changes to Yellow LED blinking.

Other Special Features

None

Where to find S2 DSK on product

The DSK is printed on the product itself and also packaging label can be found outside the giftbox

Classic Inclusion

Classic Inclusion:

Set your Z-Wave Gateway into Inclusion mode / Add device.

i. Start: Short press Touch Sense Button 3 times.

ii. Processing: Yellow LED and short beep sound keeping continue. For security inclusion support, you may need to entering first 5 digit

that show on QR Code label, please refer to the instructions of central controller.

iii. Success: Green LED on 1 second with 2 short beep sounds.

iv. The LED indication changes to Green LED slow blinking from Yellow LED blinking.

S2 Authenticated

S2_AUTHENTICATED

S2 Unauthenticated

S2_UNAUTHENTICATED

Outdoor Use

Product is suitable for use outdoors.

Switch Type

Describes the type of operator for a switch.