Produtos visualizados





Confianza Online


FIBARO - SMART IMPLANT sensor universal Z-Wave+

FGBS-222

Novo

Em estoque

44,99 €

Características tecnicas

Tecnologia Z-Wave Plus

Download

Informação alargada da Z-Wave (Inglês)

Nome: Smart Implant
Fabricante:FIBARO
Identificador:FGBS-222
Número de Certificação Z-Wave :ZC10-19046414
Plataforma de Hardware :ZM5101
FLiRS:Não
Tipo de Role :Always On Slave
Descrição breve :FIBARO Smart Implant allows to enhance the functionality of wired sensors and other devices by adding Z-Wave network communication.
Descrição :FIBARO Smart Implant allows to enhance the functionality of wired sensors and other devices by adding Z-Wave network communication. You can connect binary sensors, analog sensors, DS18B20 temperature sensors or DHT22 humidity and temperature sensor to report their readings to the Z-Wave controller. It can also control devices by opening/closing output contacts independently of the inputs. Main features of FIBARO Smart Implant: - Compatible with any Z-Wave or Z-Wave+ Controller, - Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 with PRNG-based encryption, - Allows for connecting sensors: o 6 DS18B20 sensors, o 1 DHT sensor, o 2 2-wire analog sensor, o 2 3-wire analog sensor, o 2 binary sensors. - Works as a Z-Wave signal repeater, - Built-in temperature sensor.

Descarregue o manual a partir de aqui.

Grupo
Nodos máximos
Descrição
1
1
“Lifeline” reports the device status and allows for assigning single device only (main controller by default).
2
5
“On/Off (IN1)” is assigned to IN1 input terminal (uses Basic command class).
3
5
“On/Off (IN2)” is assigned to IN2 input terminal (uses Basic command class).
Número
Tamanho (Bytes)
Valor por defeito
Nome
Descrição
150
1
10
Input 1 - sensitivity
This parameter defines the inertia time of IN1 input in alarm modes. Adjust this parameter to prevent bouncing or signal disruptions.Parameter is relevant only if parameter 20 is set to 0 or 1 (alarm mode).
151
1
10
Input 2 - sensitivity
This parameter defines the inertia time of IN2 input in alarm modes. Adjust this parameter to prevent bouncing or signal disruptions. Parameter is relevant only if parameter 21 is set to 0 or 1 (alarm mode).
152
2
0
Input 1 - delay of alarm cancellation
This parameter defines additional delay of cancelling the alarm on IN1 input. Parameter is relevant only if parameter 20 is set to 0 or 1 (alarm mode).
153
2
0
Input 2 - delay of alarm cancellation
This parameter defines additional delay of cancelling the alarm on IN2 input. Parameter is relevant only if parameter 21 is set to 0 or 1 (alarm mode).
154
1
0
Output 1 - logic of operation
This parameter defines logic of OUT1 output operation.
155
1
0
Output 2 - logic of operation
This parameter defines logic of OUT2 output operation.
156
2
0
Output 1 - auto off
This parameter defines time after which OUT1 will be automatically deactivated.
157
2
0
Output 2 - auto off
This parameter defines time after which OUT2 will be automatically deactivated.
20
1
2
Input 1 - operating mode
This parameter allows to choose mode of 1st input (IN1). Change it depending on connected device.
21
1
2
Input 2 - operating mode
This parameter allows to choose mode of 2nd input
24
1
0
Inputs orientation
This parameter allows reversing operation of IN1 and IN2 inputs without changing the wiring. Use in case of incorrect wiring.
25
1
0
Outputs orientation
This parameter allows reversing operation of OUT1 and OUT2 inputs without changing the wiring. Use in case of incorrect wiri ng.
40
1
0
Input 1 - sent scenes
This parameter defines which actions result in sending scene ID and attribute assigned to them (see 9: Activating scenes). Parameter is relevant only if parameter 20 is set to 2 or 3.
41
1
0
Input 2 - sent scenes
This parameter defines which actions result in sending scene ID and attribute assigned to them (see 9: Activating scenes). Parameter is relevant only if parameter 20 is set to 2 or 3.
47
2
255
Input 1 - value sent to 2nd association group when activated
This parameter defines value sent to devices in 2nd association group when IN1 input is triggered (using Basic Command Class).
49
2
0
Input 1 - value sent to 2nd association group when deactivated
This parameter defines value sent to devices in 2nd association group when IN1 input is deactivated (using Basic Command Class).
52
2
255
Input 2 - value sent to 3rd association group when activated
This parameter defines value sent to devices in 3rd association group when IN2 input is triggered (using Basic Command Class).
54
2
0
Input 2 - value sent to 3rd association group when deactivated
This parameter defines value sent to devices in 2nd association group when IN2 input is deactivated (using Basic Command Class).
63
1
5
Analog inputs - minimal change to report
This parameter defines minimal change (from the last reported) of analog input value that results in sending new report. Parameter is relevant only for analog inputs (parameter 20 or 21 set to 4 or 5).
64
2
0
Analog inputs - periodical reports
This parameter defines reporting period of analog inputs value. Periodical reports are independent from changes in value (parameter 63). Parameter is relevant only for analog inputs (parameter 20 or 21 set to 4 or 5).
65
2
5
Internal temperature sensor - minimal change to report
This parameter defines minimal change (from the last reported) of internal temperature sensor value that results in sending new report.
66
2
0
Internal temperature sensor - periodical reports
This parameter defines reporting period of internal temperature sensor value. Periodical reports are independent from changes in value (parameter 65).
67
2
5
External sensors - minimal change to report
This parameter defines minimal change (from the last reported) of external sensors values (DS18B20 or DHT22) that results in sending new report. Parameter is relevant only for connected DS18B20 or DHT22 sensors.
68
2
0
External sensors - periodical reports
This parameter defines reporting period of analog inputs value. Periodical reports are independent from changes in value (parameter 67). Parameter is relevant only for connected DS18B20 or DHT22 sensors.
Basic
COMMAND_CLASS_BASIC
Application Status
COMMAND_CLASS_APPLICATION_STATUS
Association Group Information V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Central Scene V3
COMMAND_CLASS_CENTRAL_SCENE_V3
Configuration
COMMAND_CLASS_CONFIGURATION
CRC16 Encapsulation
COMMAND_CLASS_CRC_16_ENCAP
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V4
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Notification V8
COMMAND_CLASS_NOTIFICATION_V8
Powerlevel
COMMAND_CLASS_POWERLEVEL
Protection V2
COMMAND_CLASS_PROTECTION_V2
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Sensor Multilevel V11
COMMAND_CLASS_SENSOR_MULTILEVEL_V11
Supervision
COMMAND_CLASS_SUPERVISION
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Factory Reset
Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted.



Resetting the device is not the recommended way of

removing the device from the Z-Wave network. Use this procedure only when the network primary controller is missing or inoperable. Certain device removal can be achieved by the procedure of removing described.



1. Press and hold the button to enter the menu.

2. Release button when the device glows yellow.

3. Quickly click the button to confirm.

4. After few seconds the device will be restarted, which is signalled with the red colour.





Inclusion
To add the device to the Z-Wave network manually:

1. Power the device.

2. Set the main controller in (Security/non-Security Mode) add mode (see the controller’s manual).

3. Quickly, triple click button on the device housing or switch connected to IN1 or IN2.

4. If you are adding in Security S2 Authenticated, scan the DSK QR code or input the 5-digit PIN code (label on the bottom of the box).

5. LED will start blinking yellow, wait for the adding process to end.

6. Successful adding will be confirmed by the Z-Wave controller’s message.



To add the device to the Z-Wave network using Smart Start:

1. Set the main controller in Security S2 Authenticated add mode (see the controller’s manual).

2. Scan the DSK QR code or input the 5-digit PIN code (label on the bottom of the box).

3. Power the device.

4. LED will start blinking yellow, wait for the adding process to end.

5. Successful adding will be confirmed by the Z-Wave controller’s message.

Exclusion
To remove the device from the Z-Wave network:

1. Power the device.

2. Set the main controller into remove mode (see the controller’s manual).

3. Quickly, triple click button on the device housing or switch connected to IN1 or IN2.

4. LED will start blinking yellow, wait for the removing process to end.

5. Successful removing will be confirmed by the Z-Wave controller’s message.

Device Wake-Up
FIBARO Smart Implant is powered using DC power supply unit so it is always awake.
S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Color
If the product is only available in one color, pick the color from the list.
Sensors
Sensor types supported by the product.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).

 

Avaliações

Escrever uma avaliação

FIBARO - SMART IMPLANT sensor universal Z-Wave+

FIBARO - SMART IMPLANT sensor universal Z-Wave+

Accessories

9 outros produtos na mesma categoria:

Clientes que compraram este produto também compraram: