Productos más vistos

POPP Detector de Moho...

Este detector Z-Wave protege su hogar...

Ver más grande

Previo

POPP Detector de Moho Z-Wave Plus

Referencia POPE701202

Estado: Nuevo

Este detector Z-Wave protege su hogar contra el moho ya que el detector mide la temperatura y la humedad ambiente. El detector de moho detecta las combinaciones especificadas de temperatura y humedad, que pueden llevar a la formación de moho en su estancia.

Más detalles

En Stock - Envío inmediato

Eliminar de mis favoritos
Agregar este producto a mis favoritos
Imprimir

Características técnicas

Tecnología	Z-Wave Plus

Descripción

El detector de moho POPP protege su hogar contra la formación de moho. El detector tiene un diseño único y elegante que se adapta a cada hogar inteligente. Debido a su diseño delgado, el Detector de molde se puede colocar en cualquier posición, que debe ser supervisada.

Para proteger su hogar contra el moho, el detector mide la temperatura y la humedad de su ambiente. El detector de moho detecta las combinaciones especificadas de temperatura y humedad, que pueden llevar a la formación de moho. Si se alcanza un rango específico de humedad y temperatura, lo que lleva a la formación de moho, el detector envía una advertencia a su puerta de entrada Z-Wave Smart Home. Con eso siempre estarás informado sobre el peligro de la formación de moho.

Gracias al detector de moho, se pueden evitar los daños en edificios y apartamentos a través del moho. Si el detector de moho detecta cualquier peligro de moho, el sistema de aire se puede iniciar automáticamente, se puede abrir el motor de la ventana automática o se aludirá a los residentes a través de un mensaje de empuje para ventilar las habitaciones.

Presupuesto:

Medición de la temperatura en ° C +/- 0.2 ° C, 0 a + 65 ° C
Medición de humedad en% 0-100%; +/- 3.5%; +/- Histéresis
Advertencia si existe un peligro de formación de moho basado en valores de temperatura y humedad.
LED para señalizar cuando se produce peligro de formación de moho
Duración de la batería de hasta 3 años.
Z-Wave Plus
Z-Wave Smart Start y S2 Security
Dimensiones en mm: 18x20x70.
Alcance de la entrega:

Detector de molde POPP
1x ½ AA 3.6V batería de litio
Adhesivo y tornillos.
Guía de inicio rápido en EN & DE

Información Ampliada Z-Wave (Inglés)

Nombre: Mold Detector

Fabricante:Popp & Co.

Identificador:POPE700878

Número de Certificación Z-Wave:ZC10-19026384

Plataforma Hardware:ZM5101

FLiRS:NO

Tipo de Role:Reporting Sleeping Slave

Descripción Corta:The device measures environmental parameters and will warn when the air in the room will allow growth of mold.

Descripción:This device measures the three air quality parameters temperature, humidity and dew point an reports them to a central controller. Beside this, the device can directly control groups of other Z-Wave devices on over- and undershooting a set temperature and/or humidity parameter. This can be used to establish control loops for temperature and humidity. The device wakes up every 4 minutes to measure the values and it will send unsolicited reports when values change. Additionally, the device will report all values on request. The mold detector is actively monitoring the danger of mold in a room based on the temperature and humidity and will issue alarm warnings when critical air conditions met. Wireless Alarm and red and a green blinking LED will indicate a mold condition. This local LED warning function is also available when the device is not included in any Z-Wave network and works stand alone.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

Z-Wave Plus Lifeline

Temperature High Trigger

Temperature Low Trigger

Humidity High Trigger

Humidity Low Trigger

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

Minimum Temperature change to report

This value defines the minimum change of temperature to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the temperature changes. However, periodic reports, managed by configuration parameter 4, may still be active.

High Temperature Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 2

-1

Low Humidity Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 5

High Humidity Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 4

Minimum humidity change to report

This value defines the minimum change of humidity to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the humidity changes. However, periodic reports, managed by configuration parameter 4, may still be active.

43200

Periodic Reports

This parameter defines the time interval to send an unsolicited report. If the value is set to 0, there will be no periodic reports sent to the controller. However, reports on temperature/humidity changes, managed by configuration parameters 1 and 2, may still be active.

Temperature Upper Watermark value

This parameter defines a temperature. If the measured temperature surpasses this watermark a BASIC command is sent into Association Group 2.

Temperature Lower Watermark value

This parameter defines a temperature. If the measured temperature drops below this watermark a BASIC command is sent into Association Group 3

Humidity Upper Watermark value

This parameter defines a relative humidity. If the measured relative humidity surpasses this watermark a BASIC command is sent into Association Group 4

Humidity Lower Watermark value

This parameter defines a relative humidity. If the measured temperature drops below this relative humidity a BASIC command is sent into Association Group 5

-1

Low Temperature Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 3

Basic

COMMAND_CLASS_BASIC

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Battery

COMMAND_CLASS_BATTERY

Configuration

COMMAND_CLASS_CONFIGURATION

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V4

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Notification V8

COMMAND_CLASS_NOTIFICATION_V8

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S2

COMMAND_CLASS_SECURITY_2

Sensor Binary V2

COMMAND_CLASS_SENSOR_BINARY_V2

Sensor Multilevel V8

COMMAND_CLASS_SENSOR_MULTILEVEL_V8

Supervision

COMMAND_CLASS_SUPERVISION

Transport Service V2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Version V3

COMMAND_CLASS_VERSION_V3

Wake Up V2

COMMAND_CLASS_WAKE_UP_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Factory Reset

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Inclusion

Tripple clicking the tamper button includes (adds) the device.

Exclusion

Tripple clicking the tamper button excludes (removes) the device.

Learn Mode (adding another controller)

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Once Cover is removed and tamper switch is tripped, push the tamper for 5 seconds until red LED blinks. Then release tamper and push it again for 5 seconds until LED blinks.

Device Wake-Up

A single click on the tamper button will wakeup the device.

S2 Unauthenticated

S2_UNAUTHENTICATED

Battery Quantity

Enter the number of batteries of the designated type that the product uses.

Battery Type

Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.

Color

If the product is only available in one color, pick the color from the list.

Firmware Updatable

Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.