Productos más vistos





Confianza Online


Multisensor 4 en 1 Z-Wave de ZIPATO PIR (Movimiento) + Puerta / Ventana + luminosidad + temperatura Ver más grande

ZIPATO Multisensor QUAD MODOLITE 4-en-1 Z-Wave Plus con PIR (Movimiento) + Puerta / Ventana + luminosidad + temperatura

ZIP-PSM02-EU

Nuevo

Multi-sensor 4 en 1 de tecnología Z-Wave Plus del fabricante Zipato. Integra PIR(Movimiento) + Puerta / Ventana + luminosidad + temperatura

Más detalles

En Stock - Envío inmediato

59,99 €

Características técnicas

Tecnología Z-Wave Plus

Descripción

Este multisensor de Zipato de elegante diseño dispone de múltiples funciones domóticas. Se le llama "QUAD MODOLITE". Así, dispone de detección PIR (Detector movimiento), puerta / ventana (contacto magnético), temperatura y luminosidad, 4 sensores en un único dispositivo integrado y compacto, basado en la tecnología Z-Wave Plus.

Detecta subidas de temperatura, cambios de brillo, movimiento (PIR), y apertura de puertas o ventanas

Frecuencia: 868.42 / 908.42Mhz 

Dimensiones: 

Sensor: 28 x 96 x 23 mm
Imán: 10 x 50 x 12 mm 

Características 

• (1) detector puerta / ventana (2) PIR (3) Iuminosidad y (4) temperatura, en un sensor 
• Dispone de chip de la serie 400 Z-Wave, con soporte de múltiples canales y mayor velocidad de datos (9.6 / 40 / 100kbps) 
• (Potencia de salida + 2.5dBm en comparación con la serie 300 -2.5dBm módulo Z-Wave), potencia de salida superior para mejorar el alcance de la comunicación 
• Gama de luminosidad: 0-500 lx 
• Temperatura de funcionamiento: -10 ~ 40 ° C. Sólo para uso en interiores. 
• Batería de litio CR123A 1500mA para garantizar la vida de la batería 2 años 
• Sensor de luz empotrado, mientras que se aplica para el control de la luminosidad
• Ángulo de detección de PIR : 90 °
• Rango de detección de PIR : de 8 a 10m
• Peso: aprox 52gr
• Protección contrasabotajes y manipulaciones (Tamper)
• Fácil de instalar 
• Indicador de batería baja 
• Z-Wave Plus
• Part 15.249 FCC / EN300 220-1 / certificación 
• NCC

Información Ampliada Z-Wave (Inglés)

Nombre: Multisensor QUAD - MODOLITE, Z-wave
Fabricante:Zipato
Identificador:ph-psm02.eu
Número de Certificación Z-Wave:ZC10-17065644
Plataforma Hardware:SD3502
FLiRS:NO
Tipo de Role:Reporting Sleeping Slave
Descripción Corta:Zipato Multisensor Quad offers elaborate security and ambient sensing options.
Descripción:Zipato Multisensor Quad offers elaborate security and ambient sensing options. Multifunctional nature of this product allows you to detect motion, monitor opened/closed status of any opening object, measure room’s ambient temperature and light intensity.

Descargue el manual desde aquí.

Grupo
Max Nodos
Descripción
1
8
Z-Wave Plus Lifeline
2
8
Lighting group control
Número
Tamaño (Bytes)
Valor por Defecto
Nombre
Descripción
10
1
12
Auto Report Battery Time
The interval time for auto report the battery level. 0 means turn off auto report battery. The default value is 12. The tick time can setting by the configuration No.20.
11
1
12
Auto Report Door/ Window State Time
The interval time for auto report the door/ window state. 0 means turn off auto report door/window state. The default value is 12. The tick time can setting by the configuration No.20.
12
1
12
Auto Report Illumination Time
The interval time for auto report the illumination. 0 means turn off auto report illumination. The default value is 12. The tick time can setting by the configuration No.20.
13
1
12
Auto Report Temperature Time
The interval time for auto report the temperature. 0 means turn off auto report illumination. The default value is 12. The tick time can setting by the configuration No.20.
2
1
-1
Basic Set Level
Setting the BASIC command value to turn on the light. The 0xFF(-1) means turn on the light. For dimmer equipment 1 to 100 means the light strength.
20
1
30
Auto Report Tick Interval
The interval time for auto report each tick. Setting this configuration will effect configuration No.10, No.11, No.12 and No.13. Caution: Setting to 0 means turn off all auto report function.
21
1
1
Temperature Differential Report
The temperature differential to report. 0 means turn off this function. The unit is Fahrenheit. Enable this function the device will detect every minutes. And when the temperature is over 140 degree Fahrenheit, it will continue report. Enable this functionality will cause some issue please see the detail in the “Temperature Report” section.
22
1
0
Illumination Differential Report
The illumination differential to report. 0 means turn off this function. The unit is percentage. Enable this function the device will detect every minutes. Enable this functionality will cause some issue please see the detail in the “Illumination Report” section.
3
1
80
PIR Sensitivity
PIR sensitivity settings. 0 means disable the PIR motion. 1 means the lowest sensitivity, 99 means the highest sensitivity. High sensitivity means can detected long distance, but if there is more noise signal in the environment, it will re-trigger too frequency.
4
1
99
Light Threshold
Setting the illumination threshold to turn on the light. When the event triggered and the environment illumination lower then the threshold, the device will turn on the light. 0 means turn off illumination detected function. And never turn on the light. 1 means darkest. 99 means brightest. 100 means turn off illumination detected function. And always turn on the light. Notice: In none test mode, only the value in 1 to 99 will enable the illumination detected function and update the illumination value.
5
1
0
Operation Mode
Operation mode. Using bit to control.
6
1
4
Multi-Sensor Function Switch
Multisensor function switch. Using bit to control.
7
1
4
Customer Function
Customer function switch, using bit control.
8
1
3
PIR Re- Detect Interval Time
In the normal mode, after the PIR motion detected, setting the re-detect time. 8 seconds per tick, default tick is 3 (24 seconds). Setting the suitable value to prevent received the trigger signal too frequently. Also can save the battery energy.
9
1
4
Turn Off Light Time
After turn on the lighting, setting the delay time to turn off the lighting when the PIR motion is not detected. 8 seconds per tick, default tick is 4 (32 seconds). 0 means never send turn off light command.
Basic
COMMAND_CLASS_BASIC
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Battery
COMMAND_CLASS_BATTERY
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V2
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Command
COMMAND_CLASS_MULTI_CMD
Notification V4
COMMAND_CLASS_NOTIFICATION_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Sensor Binary V2
COMMAND_CLASS_SENSOR_BINARY_V2
Sensor Multilevel V5
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
Version V2
COMMAND_CLASS_VERSION_V2
Wake Up V2
COMMAND_CLASS_WAKE_UP_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Device Wake-Up
If the user want to wake-up the device immediately, please remove

the front cover, and press the tamper key once. The device will

wake-up 10 seconds.
Inclusion
Put the Z-Wave Controller in inclusion mode. Pressing tamper key three times within 1.5 seconds will enter inclusion mode.

After successful inclusion, the device will wake to receive the

setting command from Z-Wave Controller in about 20 seconds.
Exclusion
Put the Z-Wave Controller in exclusion mode. Pressing tamper key three times within 1.5 seconds will enter exclusion mode. Node ID has been excluded.
Factory Reset
Use this procedure only in the event that the primary controller

is lost or otherwise inoperable.

Pressing tamper key four times within 1.5 seconds and during

4th press, hold the tamper key until LED lights up. After 3 seconds the LED will turn OFF, and after next 2 seconds, release the tamper key. If successful, the LED will light ON for one second. Otherwise, the LED will flash once.IDs are excluded and all settings will reset to factory default.
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.
Color
If the product is only available in one color, pick the color from the list.
Sensors
Sensor types supported by the product.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).
Battery Quantity
Enter the number of batteries of the designated type that the product uses.

 

Opiniones

Escribe tu opinión

ZIPATO Multisensor QUAD MODOLITE 4-en-1 Z-Wave Plus con PIR (Movimiento) + Puerta / Ventana + luminosidad + temperatura

ZIPATO Multisensor QUAD MODOLITE 4-en-1 Z-Wave Plus con PIR (Movimiento) + Puerta / Ventana + luminosidad + temperatura

Multi-sensor 4 en 1 de tecnología Z-Wave Plus del fabricante Zipato. Integra PIR(Movimiento) + Puerta / Ventana + luminosidad + temperatura

Accesorios, complementos y/o alternativas

8 otros productos de la misma categoría:

Los clientes que compraron este producto también han comprado...