dimmer qubino 0-10V sin parpadeos. Distribuidor para comprar en España

Características técnicas

Tecnología	Z-Wave Plus
Característica	Dimmer

Descripción

Qubino Flush Dimmer 0-10V: el único regulador o dimmer 0-10V Z-Wave universal

El Qubino Flush Dimmer 0-10V es un dimmer universal con una salida estándar 0-10V y una entrada multifunción, que puede ser un botón o interruptor, un potenciómetro o una señal 0-10V. También mide el consumo de energía y soporta la conexión de un sensor de temperatura digital.

¿Para qué se utiliza?

El Qubino Flush Dimmer 0-10V es ideal para regulación de luces LED ya sea mediante control remoto y domotica para sistemas de iluminación con balastro de baja tensión.

El Qubino Flush Dimmer 0-10V es un producto Z-Wave Plus actualmente UNICO y exclusivo de su clase. Ha sido investigado y desarrollado basándonos en los usuarios y en los entusiastas del "háztelo tu mismo" DIY (Do It Yourself) que han estado buscando de forma desesperada una solución Z-Wave con una entrada/salida 0-10V. El Qubino Flush Dimmer 0-10V ha dado como resultado el dimmer perfecto para iluminación LED.

El dimmer Z-Wave más pequeño

El módulo Z-Wave Qubino Flush Dimmer 0-10V es un micromódulo que ocupa menos espacio que cualquier otro modulo con el que se le compare de cualquier otro competidor y encajará fácilmente en cualquier caja de mecanismo convencional.

Control energético

El dimmer Z-Wave Qubino Flush Dimmer 0-10V, hace medición de consumo eléctrico del aparato eléctrico conectado y de por sí, cuando está en "standby" tan sólo consume 0.5 W.

Muy versátil

El Qubino Flush Dimmer 0-10V, puede operar a través de un extenso rango de temperaturas desde los fríos -10˚C a los sofocantes 40˚C (14˚–104˚F). Soporta la conexión de un sensor de temperatura digital, que también es útil para crear escenarios complejos. Cada módulo también actúa como un repetidor con el fin de mejorar el alcance y la estabilidad de la red Z-Wave.

La instalación más sencilla

El tamaño extremadamente pequeño y una carcasa especialmente diseñada significan que la conexión del módulo dentro de una caja de montaje empotrada es sencillo. El proceso de instalación, probado y aprobado por electricistas profesionales, consta de sólo tres sencillos pasos:

1 - Retire los interruptores de la caja y desconecte los cables.
2 - Conecte los cables al módulo Qubino e insértelos en la caja.
3 - Fije los interruptores a la caja.

Los módulos Z-Wave más probados y más fiables

Los módulos Z-Wave de Qubino son productos de “instalar-y-olvidarte”. Los productos Qubino que te ofrecemos, están fabricados para durar, por lo que sólo utilizan componentes electrónicos que cumplan los más exigentes niveles de calidad. Nuestros módulos además son los micromodulos Z-Wave más testeados del mercado. El Instituto Esloveno de Calidad y Medición (The Slovenian Institute of Quality and Metrology (SIQ)), una entidad europea independiente, comprueba la calidad de los parámetros reales de nuestros productos, incluyendo el aumentos de temperatura, fabricación, resistencia del aislamiento, consumo eléctrico y sobrecargas de acuerdo las normas europeas de la máxima calidad conforme a la especificación del estándar EN 60669-2-1.

Parámetros adicionales para profesionales.

El micromódulo Qubino Flush Dimmer 0-10V dispone de 25 parámetros adicionales para su uso por expertos. Algunos de los más útiles son:

Permite el ajuste de entrada basado en el tipo de dispositivo (interruptor, potenciómetro, sensor 0-10V, etc.)
Salida de encendido / apagado automático después del tiempo establecido

El micromódulo Qubino Flush Dimmer 0-10V puede ser controlado tanto a través de una red Z-Wave como a través de un interruptor de pared. Este módulo ha sido diseñado para ser montado dentro de una caja de mecanismo y oculto detrás de un interruptor de pared convencional.

Especificaciones Técnicas y esquemas eléctricos:

Alimentación:	12 – 24 VDC
Max. Voltaje de control de "sinking"	-20 / +20 VDC
Tensión máxima de control de abastecimiento	0 – 11 VDC
Max. sinking current	2 mA
Max. sourcing current	7 mA
Precisión de la medición de potencia:	<3% FS
Rango del sensor digital de temperatura:	-50° ~ +125°C, resolucion 0.1°C
Longitud del cable del sensor digital de temperatura:	1000 mm
Temperatura de Operacion:	-10° ~ +40°C
Distancia	hasta 30 m en interior (dependiendo de materiales)
Dimensiones (WxHxD)	41.8 x 36.8 x 15.4 mm
(packaging)	(115 x 96 x 22)
Peso (incluyendo packaging)	28 g (34 g)
Consumo eléctrico en standby	0.5 W
Para instalación en cajas de mecanismo	Ø ≥ 60 mm or 2 M

Descargar

QubinoFlushDimmer0-10V.pdf

Manual del Usuario de Qubino Flush Dimmer 0-10V Version 1.3en ingles

Descargar (528.87k)

Información Ampliada Z-Wave (Inglés)

Nombre: Qubino Flush Dimmer 0-10V

Fabricante:QUBINO

Identificador:ZMNHVD1

Número de Certificación Z-Wave:ZC10-17025424

Plataforma Hardware:ZM5202

FLiRS:NO

Tipo de Role:Always On Slave

Descripción Corta:The Qubino Flush Dimmer 0-10V is ideal for remotely dimming LED lights with low voltage ballast.

Descripción:The Qubino Flush Dimmer 0-10V is a universal dimmer with a standard 0-10V output and a multi-function input, which may be a push button or switch, a potentiometer or a 0-10V signal. It also measures power consumption and supports the connection of a digital temperature sensor.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1

Z-Wave Plus Lifeline

2

16

Basic On/Off

3

16

Start Level Change/Stop Level Change

4

16

Multilevel Set

5

16

Multilevel Sensor Report (triggered at change of analogue sensor)

6

16

Multilevel Sensor Report (triggered at change of temperature sensor)

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

1

0

Input 1 switch type

By this parameter the user can set input based on device type (switch, potentiometer, 0-10V sensor,..). NOTE: After parameter change to value 3, 4 or 5 first exclude module (without setting parameters to default value) then wait at least 30s and then re include the module!

10

2

255

Activate / deactivate functions ALL ON / ALL OFF

Flush Dimmer 0-10V module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.

11

2

0

Automatic turning off output after set time

Turns off the output after set time.

110

2

32536

Temperature sensor offset settings

Set value is added or subtracted to actual measured value by sensor.

12

2

0

Automatic turning on output after set time

Turns on the output after set time.

120

1

5

Digital temperature sensor reporting

Digital temperature sensor reporting If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter. Available configuration parameters (data type is 1 Byte DEC): • default value 5 = 0,5°C change • 0 - Reporting disabled • 1 - 127 = 0,1°C - 12,7°C, step is 0,1°C

140

2

5

Input I1 Sensor reporting

Input I1 Sensor reporting If analogue sensor is connected, module reports measured value on change defined by this parameter.

141

1

5

Input I1 0-10V reporting threshold

Parameter is associated with Association group No. 2. Below this value, the Association No. 2 will report Basic Set 0xFF and above this value will report Basic Set 0xFF. Basic Set is reported only, when the input value changes for more than 10% (1V).

143

2

0

Minimum sensor range value

Value that must correspond to minimum sensor range value. Valid only if parameter 1 is set to values 3, 4 or 5). Available configuration parameters (data type is 2 Byte DEC): • default value 0 = 0.0°C / 0Lux / 0.0%rh • 0 - 10000 – value from 0 to 1000 (resolution 0,1) • 10001 – 20000 – value from -0,1 to -1000 (resolution 0,1) NOTE: Minimum value must not be higher than maximum value!

144

2

1000

Maximum sensor range value

Value that must correspond to maximum sensor range value. Valid only if parameter 1 is set to values 3, 4 or 5). NOTE: Maximum value must not be lower than minimum value!

21

1

0

Enable/Disable Double click function

If Double click function is enabled, a fast double click on the push button will set dimming power at maximum dimming value. Valid only if input is set as mono-stable (push button).

250

1

0

Unsecure / Secure Inclusion

A Flush dimmer supports secure and unsecure inclusion. Even if the controller does not support security command classes, a dimmer could be included as unsecure and keep all the functionality.

30

1

0

Saving the state of the device after a power failure

Based on the parameter settings the stores/does not store the last value of the output after power failure.

52

1

0

Auto or manual selection

This parameter is influencing on the software only when the value of parameter number 1 is set to value 3, 4 or 5. In manual mode regulation (how the input influence on output) is disabled.

53

1

0

PID value inside deadband

NOTE: When ZERO PID inside deadband is forced to zero. LASTVALUE means that PID remains on same level as was before entering into deadband.

54

1

PID deadband

NOTE: This parameter defines the zone where PID is not active. If the temperature difference between actual and setpoint is bigger than PID deadband, then the PID will start to regulate the system, otherwise the PID is zero or fixed.

55

1

5

Integral sampling time

Parameter defines the time between samples. On each sample the controller capture difference between SP-act.

56

2

100

P parameter

The error is multiplied by a negative (for reverse action) proportional constant P, and added to the current output. P represents the band over which a controller's output is proportional to the error of the system. E.g. for a heater, a controller with a proportional band of 10 deg C and a setpoint of 100 deg C would have an output of 100% up to 90 deg C, 50% at 95 Deg C and 10% at 99 deg C. If the temperature overshoots the setpoint value, the heating power would be cut back further. Proportional only control can provide a stable process temperature but there will always be an error between the required setpoint and the actual process temperature.

57

2

1

I parameter

The error is integrated (averaged) over a period of time, and then multiplied by a constant I, and added to the current control output. I represents the steady state error of the system and will remove setpoint / measured value errors. For many applications Proportional + Integral control will be satisfactory with good stability and at the desired setpoint.

58

2

1

D parameter

The rate of change of the error is calculated with respect to time, multiplied by another constant D, and added to the output. The derivative term is used to determine a controller's response to a change or disturbance of the process temperature (e.g. opening an oven door). The larger the derivative term, the more rapidly the controller will respond to changes in the process value.

60

1

Minimum dimming value

NOTE: The minimum level may not be higher than the maximum level! 1% min. dimming value is defined by Z-Wave multilevel device class. When the switch type is selected as Bi-stable, it is not possible to dim the value between min and max. If Switch_multilevel_set is set to the value “0”, the output is turned OFF. If Switch_multilevel_set is set to the value “1”, the output is set to the minimum diming value.

61

1

99

Maximum dimming value

NOTE: The maximum level may not be lower than the minimum level! 99% max. dimming value is defined by Z-Wave multilevel device class. When the switch type is selected as Bi-stable, it is not possible to dim the value between min and max.

65

2

100

Dimming time (soft on/off)

Set value means time of moving the Flush Dimmer 0-10V between min. and max. dimming values by short press of push button I1 or controlled through UI (BasicSet).

66

2

3

Dimming time when key pressed

Time of moving the Flush Dimmer 0-10V between min. and max dimming values by continues hold of push button I1 or associated device.

67

1

0

Ignore start level

This parameter is used with association group 3. A receiving device SHOULD respect the start level if the Ignore Start Level bit is 0. A receiving device MUST ignore the start level if the Ignore Start Level bit is 1.

68

1

0

Dimming duration

This parameter is used with association group 3. The Duration field MUST specify the time that the transition should take from the current value to the new target value. A supporting device SHOULD respect the specified Duration value.

Basic

COMMAND_CLASS_BASIC

Switch Multilevel V3

COMMAND_CLASS_SWITCH_MULTILEVEL_V3

Association Group Information V2

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic

COMMAND_CLASS_BASIC

Configuration

COMMAND_CLASS_CONFIGURATION

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel V4

COMMAND_CLASS_MULTI_CHANNEL_V4

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S0

COMMAND_CLASS_SECURITY

Sensor Multilevel V7

COMMAND_CLASS_SENSOR_MULTILEVEL_V7

Switch All

COMMAND_CLASS_SWITCH_ALL

Switch Binary

COMMAND_CLASS_SWITCH_BINARY

Switch Multilevel V3

COMMAND_CLASS_SWITCH_MULTILEVEL_V3

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Exclusion

• Connect module to power supply

• bring module within maximum 1 meter (3 feet) of the main controller,

• enable add/remove mode on main controller,

• press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or

• press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second.

By this function all parameters of the module are set to default values and own ID is deleted.

If push button I1 is pressed three times within 3s (or service button S is pressed more than 2 and less than 6 seconds) module is excluded, but configuration parameters are not set to default values.

NOTE 1: If the module is included with parameter 1 value 3, 4 or 5 and module reset is done, wait at least 30s before next inclusion.

NOTE 2: Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Factory Reset

• Press push button I1 five times within 3s (5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply or

• press service button S (only applicable for 24 V SELV supply voltage) for more than 6 second.

Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Inclusion

• Connect module to power supply (with

temperature sensor connected - if purchased),

• enable add/remove mode on main controller

• auto-inclusion (works for about 5 seconds after connected to power supply) or

• press service button S for more than 2 second or

• press push button I1 three times within 3s (3 times change switch state within 3 seconds).

NOTE1: For auto-inclusion procedure, first set main controller into inclusion mode and then connect module to power supply.

NOTE2: When connecting temperature sensor to module that has already been included, you have to exclude module first. Switch off power supply, connect the sensor and re-include the module.

Color

If the product is only available in one color, pick the color from the list.

Sensors

Sensor types supported by the product.

Switch Type

Describes the type of operator for a switch.

Switch Load Capacity Current

The amount of switch load energy the product is rated for in Amps