Fibaro Single Switch 2 - relé sencillo On / Off medición de consumo

Características técnicas

Tecnología	Z-Wave Plus
Característica	Medición de Consumo

Descripción

El nuevo interruptor / relé simple de Fibaro, Fibaro FGS-213 "Single Switch 2" disponible como un interruptor o relé simple fue diseñado para activar y desactivar dispositivos eléctricos. Gracias a su pequeño tamaño se puede montar en cajas de mecanismos o carcasas de electrodomésticos en su interior. El módulo se controla ya sea a través de la red Z-Wave o mediante un interruptor convencional. Dispone de función de medida de potencia y consumo de energía de uso que le permite controlar y reducir sus facturas de electricidad. Conecte su Fibaro FGS-213 "Single Switch 2" en el sistema domotico Z-Wave junto a otros dispositivos para disfrutar de posibilidades casi infinitas!

Al tratarse de 1 relé sencillo dispone de 1 salida:

1 salida de 8A max. (1920W max. a 240V) con carga resistiva.

Mecanismo de activación de escenas integrado

clases de comunicación y notificación de seguridad
menú de configuración con un diodo
Última generación Z-Wave con chip de la serie 500
Compatible Z-Wave Plus

Realiza funciones de repetidor Z-Wave
Mide energía y potencia de los dispositivos conectados
Soporta el modo seguro (Red de Seguridad Z-Wave) con cifrado AES-128
Un complejo sistema de control para cada canal
Un complejo sistema de activación de escena para cada canal (manejo de la escena)
1 a 3 pulsaciones y manteniendo la tecla pulsada se pueden asignar a cuatro acciones diferentes
medición de energía muy precisa +/- 1% de potencia por encima de 5W
Notificaciones inteligentes
Conexiones mejoradas
menú de configuración sencillo
Dispone de testigo de prueba de cobertura de la red Z-Wave
Actualizaciones de software*
compatibilidad con la certificación confirmada por FCC, DEKRA, Z-Wave

Tenga en cuenta que este módulo requiere de NEUTRO para operar. La salida no es libre de potencial, lo que no permite controlar un contacto seco o cargar otra tensión de alimentación de la entrada.

REPETIMOS: no puede ser utilizado en un esquema de conexión del tipo "contacto seco", como podía hacerlo su predecesor, el Fibaro FGS-212.

Esquema de Cableado del relé Fibaro FGS-213

Cableado del FGS-213 de Fibaro

Imagen de cableado tanto con 1 como con 2 circuitos

Resumen:

1 salida:

de 8A max. (1920W max. a 240V) con carga resistiva.

la medición precisa de consumo (+/- 1% de 5W).
Z-Wave + 500 Series (mejor comunicación a distancia).
comunicaciones seguras con el cifrado AES-128.
Capacidad de desencadenar escenas de domótica a través de las entradas S1 y S2 (4 posibles escenas por botón).
* comprobar si el controlador domótico es compatible con esta característica concreta
Configuración con función de menú interactivo y probador de red Z-Wave con LED

Tamaño rele fibaro

Información Ampliada Z-Wave (Inglés)

Nombre: Single Switch 2

Fabricante:FIBARO

Identificador:FGS-213

Número de Certificación Z-Wave:ZC10-19076667

Plataforma Hardware:ZM5101

FLiRS:NO

Tipo de Role:Always On Slave

Descripción Corta:FIBARO Single Switch 2 is designed to turn electrical devices on and off and to measure their power and energy consumption.

Descripción:The remotely operated FIBARO Single Switch 2 is designed to turn electrical devices on and off and to measure their power and energy consumption. The compact size of the device makes it the world's smallest of its type and allows for the product to be installed in wall switch boxes or housings. FIBARO Single Switch 2 can be controlled either via Z-Wave network or with a wall switch through a direct connection.

Descargue el manual desde aquí.

Grupo

Max Nodos

Descripción

1

“Lifeline” reports the device status and allows for assigning single device only (main controller by default).

2

5

“On/Off (S1)” is assigned to switch connected to the S1 terminal (uses Basic command class).

3

5

“Dimmer (S1)” is assigned to switch connected to the S1 terminal (uses Switch Multilevel command class).

4

5

“On/Off (S2)” is assigned to switch connected to the S2 terminal (uses Basic command class).

5

“Dimmer (S2)” is assigned to switch connected to the S2 terminal (uses Switch Multilevel command class).

Número

Tamaño (Bytes)

Valor por Defecto

Nombre

Descripción

10

1

0

First channel - operating mode

This parameter allows to choose operating for the 1st channel controlled by the S1 switch.

11

1

0

First channel - reaction to switch for delay/auto ON/OFF modes

This parameter determines how the device in timed mode reacts to pushing the switch connected to the S1 terminal.

12

2

50

First channel - time parameter for delay/auto ON/OFF modes

This parameter allows to set time parameter used in timed modes.

13

2

5

First channel - pulse time for flashing mode

This parameter allows to set pulse time used in flashing mode.

20

1

2

Switch type

This parameter as what type the device should treat the switch connected to the S1 and S2 terminals.

21

1

0

Flashing mode - reports

This parameter allows to define if the device sends reports during the flashing mode.

27

1

15

Associations in Z-Wave network security mode

This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. This parameter does not apply to 1st „Lifeline” group. NOTE Parameter 27 values may be combined, e.g. 1+2=3 means that 2nd & 3rd groups are sent as secure.

28

1

0

S1 switch - scenes sent

This parameter determines which actions result in sending scene assigned to them. NOTE Parameter 28 values may be combined, e.g. 1+2=3 means that scenes for single and double click are sent.

29

1

0

S2 switch - scenes sent

This parameter determines which actions result in sending scene IDs assigned to them. NOTE Parameter 29 values may be combined, e.g. 1+2=3 means that scenes for single and double click are sent.

30

1

0

S1 switch - associations sent to 2nd and 3rd association groups

This parameter determines which actions are ignored when sending commands to devices associated in 2nd and 3rd association group. All actions are active by default. NOTE Parameter 30 values may be combined, e.g. 1+2=3 means that associations for turning ON and OFF are not sent. NOTE *Hold and release is inactive when parameter 20 is set to 1 or 2. **Double click is inactive when parameter 20 is set to 1.

31

2

255

S1 switch - Switch ON value sent to 2nd and 3rd association groups

This parameter defines value sent with Switch ON command to devices associated in 2nd and 3rd association group.

32

2

0

S1 switch - Switch OFF value sent to 2nd and 3rd association groups

This parameter defines value sent with Switch OFF command to devices associated in 2nd and 3rd association group. NOTE Setting parameters 31-33, 36-38 to appropriate value should result in:

33

2

99

S1 switch - Double Click value sent to 2nd and 3rd association groups

This parameter defines value sent with Double Click command to devices associated in 2nd and 3rd association group.

35

1

0

S2 switch - associations sent to 4th and 5th association groups

This parameter determines which actions result in sending commands to devices associated in 4th and 5th association group. All actions are active by default. NOTE Parameter 35 values may be combined, e.g. 1+2=3 means that associations for turning ON and OFF are not sent. NOTE *Hold and release is inactive when parameter 20 is set to 1 or 2. **Double click is inactive when parameter 20 is set to 1.

36

2

255

S2 switch - Switch ON value sent to 4th and 5th association groups

This parameter defines value sent with Switch ON command to devices associated in 4th and 5th association group.

37

2

0

S2 switch - Switch OFF value sent to 4th and 5th association groups

This parameter defines value sent with Switch OFF command to devices associated in 4th and 5th association group.

38

2

99

S2 switch - Double Click value sent to 4th and 5th association groups

This parameter defines value sent with Double Click command to devices associated in 4th and 5th association group.

40

1

3

Reaction to General Alarm

This parameter determines how the device will react to General Alarm frame

41

1

2

Reaction to Flood Alarm

This parameter determines how the device will react to Flood Alarm frame.

42

1

3

Reaction to CO/CO2/Smoke Alarm

This parameter determines how the device will react to CO, CO2 or Smoke frame.

43

1

Reaction to Heat Alarm

This parameter determines how the device will react to Heat Alarm frame.

44

2

600

Flashing alarm duration

This parameter allows to set duration of flashing alarm mode.

50

1

20

First channel - power reports

This parameter determines the minimum change in consumed power that will result in sending new power report to the main controller.

51

1

10

First channel - minimal time between power reports

This parameter determines minimum time that has to elapse before sending new power report to the main controller.

53

2

100

First channel - energy reports

This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller.

58

2

3600

Periodic power reports

This parameter determines in what time interval the periodic power reports are sent to the main controller.

59

2

3600

Periodic energy reports

This parameter determines in what time interval the periodic energy reports are sent to the main controller.

60

1

0

Measuring energy consumed by the device itself

This parameter determines whether energy metering should include the amount of energy consumed by the device itself. Results are being added to energy reports for first endpoint.

9

1

Restore state after power failure

This parameter determines if the device will return to state prior to the power failure after power is restored.

Basic

COMMAND_CLASS_BASIC

Notification V5

COMMAND_CLASS_NOTIFICATION_V5

Switch Multilevel V3

COMMAND_CLASS_SWITCH_MULTILEVEL_V3

Application Status

COMMAND_CLASS_APPLICATION_STATUS

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Basic

COMMAND_CLASS_BASIC

Central Scene V2

COMMAND_CLASS_CENTRAL_SCENE_V2

Configuration

COMMAND_CLASS_CONFIGURATION

CRC16 Encapsulation

COMMAND_CLASS_CRC_16_ENCAP

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V3

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V3

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Meter V3

COMMAND_CLASS_METER_V3

Multi-Channel Association V3

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel V4

COMMAND_CLASS_MULTI_CHANNEL_V4

Notification V5

COMMAND_CLASS_NOTIFICATION_V5

Powerlevel

COMMAND_CLASS_POWERLEVEL

Protection V2

COMMAND_CLASS_PROTECTION_V2

Security S0

COMMAND_CLASS_SECURITY

Switch Binary

COMMAND_CLASS_SWITCH_BINARY

Version V2

COMMAND_CLASS_VERSION_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Exclusion

1) Make sure the Switch 2 is within the direct range of your Z-Wave controller.

2) Identify the S1 switch or the B-button (located on the device’s housing).

3) Set the main controller in remove mode (see the controller’s manual).

4) Quickly, three times press the S1 switch or the B-button.

5) Wait for the removing process to end.

6) Successful removing will be confirmed by the Z-Wave controller’s message

Inclusion

1) Switch off the mains voltage (disable the fuse).

2) Make sure the Switch 2 is within the direct range of your Z-Wave controller.

3) Connect the device in accordance with one of the diagrams included in the manual.

4) After verifying correctness of the connection switch on the mains voltage.

5) Identify the S1 switch or the B-button (located on the device’s housing).

6) Set the main controller in (security/non-security) add mode (see the controller’s manual).

7) Quickly, three times press the S1 switch or the B-button.

8) Wait for the adding process to end.

9) Successful adding will be confirmed by the Z-Wave controller’s message.

Factory Reset

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. In order to reset the device:

1) Switch off the mains voltage (disable the fuse).

2) Remove the Switch 2 from the wall switch box.

3) Switch on the mains voltage.

4) Press and hold the B-button to enter the menu.

5) Wait for the visual LED indicator to glow yellow.

6) Quickly release and click the B-button again.

7) After few seconds the device will be restarted, which is signalled with the red LED indicator colour.

Use reset procedure only if the primary controller is missing or inoperable.

Device Wake-Up

The FIBARO Single Switch 2 is powered with the mains voltage so it is always awake.

Additional Special Features

Z-Wave Plus communication protocol

Active power and energy metering functionality

Z-Wave range tester

LED diode

Color

If the product is only available in one color, pick the color from the list.

Supported Meter Type

Indicate which type of metering is supported by the device.

Supported Notification Types

Select the Notification Types that the product handles (controllers), or sends (slaves).

Switch Load Capacity Current

The amount of switch load energy the product is rated for in Amps