Number
Size (Bytes)
Default Value
Name
Description
1
1
1
TIME CORRECTION
Time correction by controller
10
1
15
TOUCH SENSITIVITY
Touch buttons sensitivity:
10=Supper sensitive.
50=lowest sensitivity.
11
1
0
TEMP SENSOR CORRECTION
Temperature sensor calibration, x10
12
1
1
BACKLIGHT ACTIVE COLOR
Active state backlight color
13
1
1
BACKLIGHT AUTO BRIGHTNESS
Backlight auto-brightness control
14
1
10
BACKLIGHT MANUAL BRIGHTNESS LEVEL
Backlight brightness in manual mode.
The Backlight Brightness Level Parameter will take effect when Parameter 13 is set to Manual Control (value = 0).
15
1
1
BACKLIGHT1 CONTROL SOURCE
Backlight 1 control source
16
1
1
BACKLIGHT2 CONTROL SOURCE
Backlight 2 control source
17
1
1
BACKLIGHT3 CONTROL SOURCE
Backlight 3 control source
18
1
1
BACKLIGHT4 CONTROL SOURCE
Backlight 4 control source
19
1
1
BACKLIGHT5 CONTROL SOURCE
Backlight 5 control source
2
1
1
WEEKDAY
The day of the week (starting from Monday)
20
1
1
RELAY1 CONTROL SOURCE
Relay 1 control source
21
1
2
RELAY2 CONTROL SOURCE
Relay 2 control source
22
1
3
RELAY3 CONTROL SOURCE
Relay 3 control source
23
1
4
RELAY4 CONTROL SOURCE
Relay 4 control source
24
1
5
RELAY5 CONTROL SOURCE
Relay 5 control source
25
1
1
HOLD1 CONTROL MODE
Hold control mode for touch button 1
26
1
1
HOLD2 CONTROL MODE
Hold control mode for touch button 2
27
1
1
HOLD3 CONTROL MODE
Hold control mode for touch button 3
28
1
1
HOLD4 CONTROL MODE
Hold control mode for touch button 4
29
1
1
HOLD5 CONTROL MODE
Hold control mode for touch button 5
30
1
1
CLICK1 CONTROL MODE
Click control mode for touch button 1
31
1
1
CLICK2 CONTROL MODE
Click control mode for touch button 2
32
1
1
CLICK3 CONTROL MODE
Click control mode for touch button 3
33
1
1
CLICK4 CONTROL MODE
Click control mode for touch button 4
34
1
1
CLICK5 CONTROL MODE
Click control mode for touch button 5
35
2
0
RELAY1 TIMER DURATION
Timer mode duration for button 1.
This parameter specifies the duration in seconds for the Timer mode (value 5 or 6 in Parameters 30).
Press the button and the relay output goes to ON/OFF for the specified time then changes back to OFF/ON. This function can be used to open/close garage doors, blinds, curtains, etc. or to turn attached devices like security OFF for a short time.
The time values can be configured from 0 to 43200 sec (12 hours).
Note: If the parameter value is set to “0” it will operate as a short contact (about 0.5 sec).
36
2
0
RELAY2 TIMER DURATION
Timer mode duration for button 2.
This parameter specifies the duration in seconds for the Timer mode (value 5 or 6 in Parameters 31).
Press the button and the relay output goes to ON/OFF for the specified time then changes back to OFF/ON. This function can be used to open/close garage doors, blinds, curtains, etc. or to turn attached devices like security OFF for a short time.
The time values can be configured from 0 to 43200 sec (12 hours).
Note: If the parameter value is set to “0” it will operate as a short contact (about 0.5 sec).
37
2
0
RELAY3 TIMER DURATION
Timer mode duration for button 3.
This parameter specifies the duration in seconds for the Timer mode (value 5 or 6 in Parameters 32).
Press the button and the relay output goes to ON/OFF for the specified time then changes back to OFF/ON. This function can be used to open/close garage doors, blinds, curtains, etc. or to turn attached devices like security OFF for a short time.
The time values can be configured from 0 to 43200 sec (12 hours).
Note: If the parameter value is set to “0” it will operate as a short contact (about 0.5 sec).
38
2
0
RELAY4 TIMER DURATION
Timer mode duration for button 4.
This parameter specifies the duration in seconds for the Timer mode (value 5 or 6 in Parameters 33).
Press the button and the relay output goes to ON/OFF for the specified time then changes back to OFF/ON. This function can be used to open/close garage doors, blinds, curtains, etc. or to turn attached devices like security OFF for a short time.
The time values can be configured from 0 to 43200 sec (12 hours).
Note: If the parameter value is set to “0” it will operate as a short contact (about 0.5 sec).
39
2
0
RELAY5 TIMER DURATION
Timer mode duration for button 5.
This parameter specifies the duration in seconds for the Timer mode (value 5 or 6 in Parameters 34).
Press the button and the relay output goes to ON/OFF for the specified time then changes back to OFF/ON. This function can be used to open/close garage doors, blinds, curtains, etc. or to turn attached devices like security OFF for a short time.
The time values can be configured from 0 to 43200 sec (12 hours).
Note: If the parameter value is set to “0” it will operate as a short contact (about 0.5 sec).
40
1
0
RELAY INVERSE GROUP1
Group 1 relay inverse mode.
The valid values are the following:
0, 12, 13, 14, 15, 21, 23, 24, 25, 31, 32, 34, 35, 41, 42, 43, 45, 51, 52, 53, 54
41
1
0
RELAY INVERSE GROUP2
Group 2 relay inverse mode.
The valid values are the following:
0, 12, 13, 14, 15, 21, 23, 24, 25, 31, 32, 34, 35, 41, 42, 43, 45, 51, 52, 53, 54
42
4
0
RELAY CONTROL SCENARIO1
Relays control by sensors Group 1
0, 10000000 … 53112359
Encoded as 8 digit value (ABCDEFGH):
A: Relay number (1.. 5)
B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control)
C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than)
D: State Change, 0- Switch OFF, 1- Switch ON
EFGH: Condition Value
Sensor Value for Control modes 0-2
Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
43
4
0
RELAY CONTROL SCENARIO2
Relays control by sensors Group 2
0, 10000000 … 53112359
Encoded as 8 digit value (ABCDEFGH):
A: Relay number (1.. 5)
B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control)
C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than)
D: State Change, 0- Switch OFF, 1- Switch ON
EFGH: Condition Value
Sensor Value for Control modes 0-2
Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
44
4
0
RELAY CONTROL SCENARIO3
Relays control by sensors Group 3
0, 10000000 … 53112359
Encoded as 8 digit value (ABCDEFGH):
A: Relay number (1.. 5)
B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control)
C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than)
D: State Change, 0- Switch OFF, 1- Switch ON
EFGH: Condition Value
Sensor Value for Control modes 0-2
Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
45
4
0
RELAY CONTROL SCENARIO4
Relays control by sensors Group 4
0, 10000000 … 53112359
Encoded as 8 digit value (ABCDEFGH):
A: Relay number (1.. 5)
B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control)
C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than)
D: State Change, 0- Switch OFF, 1- Switch ON
EFGH: Condition Value
Sensor Value for Control modes 0-2
Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
46
4
0
RELAY CONTROL SCENARIO5
Relays control by sensors Group 5
0, 10000000 … 53112359
Encoded as 8 digit value (ABCDEFGH):
A: Relay number (1.. 5)
B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control)
C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than)
D: State Change, 0- Switch OFF, 1- Switch ON
EFGH: Condition Value
Sensor Value for Control modes 0-2
Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
47
4
0
RELAY CONTROL SCENARIO6
Relays control by sensors Group 6
0, 10000000 … 53112359
Encoded as 8 digit value (ABCDEFGH):
A: Relay number (1.. 5)
B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control)
C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than)
D: State Change, 0- Switch OFF, 1- Switch ON
EFGH: Condition Value
Sensor Value for Control modes 0-2
Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
48
4
0
RELAY CONTROL SCENARIO7
Relays control by sensors Group 7.
0, 10000000 … 53112359
Encoded as 8 digit value (ABCDEFGH):
A: Relay number (1.. 5)
B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control)
C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than)
D: State Change, 0- Switch OFF, 1- Switch ON
EFGH: Condition Value
Sensor Value for Control modes 0-2
Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
49
4
0
RELAY CONTROL SCENARIO8
Relays control by sensors Group 8
0, 10000000 … 53112359
Encoded as 8 digit value (ABCDEFGH):
A: Relay number (1.. 5)
B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control)
C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than)
D: State Change, 0- Switch OFF, 1- Switch ON
EFGH: Condition Value
Sensor Value for Control modes 0-2
Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
5
1
10
METER REPORT INTERVAL
Energy Consumption Meter Consecutive Report Interval, minutes
50
4
0
RELAY CONTROL SCENARIO9
Relays control by sensors Group 9
0, 10000000 … 53112359
Encoded as 8 digit value (ABCDEFGH):
A: Relay number (1.. 5)
B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control)
C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than)
D: State Change, 0- Switch OFF, 1- Switch ON
EFGH: Condition Value
Sensor Value for Control modes 0-2
Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
51
4
0
RELAY CONTROL SCENARIO10
Relays control by sensors Group 10
0, 10000000 … 53112359
Encoded as 8 digit value (ABCDEFGH):
A: Relay number (1.. 5)
B: Control Mode (0-Temperature Sensor, 1-Humidity Sensor, 2-Light Sensor, 3-Time control)
C: State change condition relative to the value in HGFE Value field ( 0-Lower than, 1-Higher than)
D: State Change, 0- Switch OFF, 1- Switch ON
EFGH: Condition Value
Sensor Value for Control modes 0-2
Time Of Day for Control mode 3. EF represents Hour (0..23), GH represents Minutes (0..59)
52
2
0
RELAY1 LOAD POWER
Power load consumption (in Watts) Relay channel 1 in order to calculate total energy consumption relative to the time each relay is ON.
53
2
0
RELAY2 LOAD POWER
Power load consumption (in Watts) Relay channel 2 in order to calculate total energy consumption relative to the time each relay is ON.
54
2
0
RELAY3 LOAD POWER
Power load consumption (in Watts) Relay channel 3 in order to calculate total energy consumption relative to the time each relay is ON.
55
2
0
RELAY4 LOAD POWER
Power load consumption (in Watts) Relay channel 4 in order to calculate total energy consumption relative to the time each relay is ON.
56
2
0
RELAY5 LOAD POWER
Power load consumption (in Watts) Relay channel 5 in order to calculate total energy consumption relative to the time each relay is ON.
57
1
0
TOUCH1 ASSOCIATION MODE
Touch control mode for associations with touch button 1.
This parameter is intended for use when Multilevel Switch Group Associations (Groups 3, 5, 7, 9, & 11) have been activated. Defines the logic of values changing if one the touch button has been held for more than one second.
58
1
0
TOUCH2 ASSOCIATION MODE
Touch control mode for associations with touch button 2.
This parameter is intended for use when Multilevel Switch Group Associations (Groups 3, 5, 7, 9, & 11) have been activated. Defines the logic of values changing if one the touch button has been held for more than one second.
59
1
0
TOUCH3 ASSOCIATION MODE
Touch control mode for associations with touch button 3.
This parameter is intended for use when Multilevel Switch Group Associations (Groups 3, 5, 7, 9, & 11) have been activated. Defines the logic of values changing if one the touch button has been held for more than one second.
6
1
10
SENSORS REPORT INTERVAL
Sensors Consecutive Report Interval
60
1
0
TOUCH4 ASSOCIATION MODE
Touch control mode for associations with touch button 4.
This parameter is intended for use when Multilevel Switch Group Associations (Groups 3, 5, 7, 9, & 11) have been activated. Defines the logic of values changing if one the touch button has been held for more than one second.
61
1
0
TOUCH5 ASSOCIATION MODE
Touch control mode for associations with touch button 5.
This parameter is intended for use when Multilevel Switch Group Associations (Groups 3, 5, 7, 9, & 11) have been activated. Defines the logic of values changing if one the touch button has been held for more than one second.
7
1
5
TEMPERATURE REPORT THRESHOLD
Temperature difference to send to controller, value X 10
8
1
2
HUMIDITY REPORT THRESHOLD
Humidity difference to send to controller, value X 10
9
1
50
LIGHT REPORT THRESHOLD
Luminance difference to send to controller in %