Viewed products





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

Qubino Smart Plug 16A - Small size Z-Wave Plus on-off wallplug

ZMNHYD1

New

Smart wallplug with consumption measurement. The smallest 16A Z-Wave plug on the market. With Z-Wave Plus technology and consumption measurement. It does not limit the power of the plug to which we connect the smart plug since these are usually 16 amps, like this SmartPlug 16A of Qubino.

More details

In Stock

67,58 €

-12%

76,80 €

Technical characteristics

Technology Z-Wave Plus
Characteristic Consumption Measurement

More info

The Qubino Smart Plug 16A Z-Wave plug is ideal for remotely and intelligently controlling electrical devices, devices and devices as well as measuring energy consumption. Without reducing the load capacity of the plug of the house to which it connects, which will normally be 16 amps, the Smart Plug 16A can handle even the most consumed devices in a home or office, such as the electric convection oven, the dryer , the washing machine or even multiple devices at once.

How can Smart Plug 16A be used?

The Smart Plug 16A can be used in many different scenarios, which can help make your life more comfortable.
There are innumerable options to use Qubino Smart Plug 16A to remotely control and measure the power consumption
of your connected devices as well as turning them on and off manually or intelligently based on scenes or reactions of events in our home automation. You can see it compared to other smart Z-Wave plugs here.

Qubino Smart Plug 16A plug

Remotely control and measure the energy consumption of an electrical device ( table lamp , for example)

Z-Wave lamp control

Remotely control and measure the energy consumption of an electrical device (domestic hot water heater , for example)

Thermos control with the mobile

Remotely control and measure the energy consumption of an electrical device (for example, an oven )

Remote control of an oven

Remotely control and measure the energy consumption of an electrical device (an iron , for example)

Remote control of iron

Remotely control and measure the power consumption of an electrical device (a fan , for example)

Remote control ceiling fan

Remotely control and measure the energy consumption of an electrical device (an electric radiator , for example)

Remote control of heating with the mobile

Measure the energy consumption of the refrigerator remotely and / or accumulated

Measure consumption of the refrigerator

Measure the power consumption of the microwave oven remotely

Measure microwave oven consumption

Remotely measure TV energy consumption

measure electric consumption television

Remotely measure the power consumption of computers and servers connected to a power outlet

Measure consumption of computers or servers

Main advantages

The intelligent Q-Plug Smart Plug 16A Z-Wave , the smallest on the market in its category, is ideal to remotely control electrical devices and measure energy consumption, without reducing the electrical power of the plug to which we connect, as is often the case happen with other competitive plugs. You can control high-consumption devices (such as measuring your power consumption and turning them on / off remotely) and it's a Plug & Play device.

Automatic switching control

The Z Wave Qubino Smart Plug 16A can turn devices / lights on or off automatically after a certain period of time (when you are away from home). For example, the light will turn off automatically if it has been on for 8 hours, say. This function is independent of other scenes and gateway commands (hub)

Control other devices in your Z-Wave network

Connect the Smart Plug 16A with other devices in your network to remotely and automatically trigger another Z-Wave device. And have other Z-Wave devices activate your Qubino Smart Plug 16A

The simplest installation

The Qubino Smart Plug 16A allows the easiest and fastest possible installation: it is a Plug & Play device which means that installation skills are not needed for device configuration. The device adapts to any schuko outlet.

S: Service button (used to include or exclude the Qubino Smart Plug 16A from the Z-Wave network and to turn on / off the internal relay when used manually)

LED1:

When the Smart Plug 16A is EXCLUDED:

When the relay is OFF:


"the blue LED flashes (1 second on, 1 second off)

When the relay is ON:


"Blue LED is on
"the red LED is flashing (0.3 sec ON, 0.3 sec OFF) when the current exceeds 14.4A
"the red LED is on after the overload occurred

When the Smart Plug 16A is INCLUDED:

When the relay is OFF:


"The LED is off

When the relay is ON:


"Blue LED is on
"the red LED is flashing (0.3 sec ON, 0.3 sec OFF) when the current exceeds 14.4A
"the red LED is on after the overload occurred

Package content:


The package contains 1 product and 1 user manual.

Dimensions of the package (WxHxD): 43 x 52 x 75 mm
Gross weight (with packaging): 80 g

Download

Extended Z-Wave info

Name: Smart Plug 16A
Manufacturer:QUBINO
Identifier:ZMNHYD1
Z-Wave Certification Number:ZC10-18116325
Hardware Plattform:ZM5101
FLiRS:NO
Role Type:Always On Slave
Short Description:The Qubino Smart Plug 16A is ideal for remotely controlling electrical devices and measuring the energy consumption.
Description:The Smart Plug 16A controls on/off function for the connected device. It also measures power consumption of the connected device according to the principle of fast sampling of voltage and current signals. A built-in microprocessor calculates energy and power from the measured signals.

Manual download HERE.

Group
Max Nodes
Description
1
1
Lifeline - Supports the following command classes: • Device Reset Locally: triggered upon request • Meter Report: triggered according to Configuration parameters 40 and 42 • Notification Report: triggered on overload/overcurrent or according to Configuration parameters 70, 71 and 72 • Switch Binary Report: triggered upon request or according to Configuration parameters 11 and 12
2
5
Plug Status - Supports the following command classes: • Basic set: triggered at change of relay state
3
5
Plug Threshold - Supports the following command classes: • Basic set: triggered at change of active power in combination with Configuration parameters 50, 51 and 52
Number
Size (Bytes)
Default Value
Name
Description
11
2
0
Parameter no. 11 - Turn Smart plug 16A Off Automatically with Timer
Parameter no. 11 - Turn Smart plug 16A Off Automatically with Timer If Smart plug 16A is ON, you can schedule it to turn OFF automatically after a period defined in this parameter. The timer is reset to zero each time the device receives an ON command, either remotely (from the gateway (hub) or associated device) or locally from the switch. Values (size is 2 byte dec): • default value 0 • 0 - Auto OFF Disabled 1 - 32535 = 1 - 32535 seconds. Auto OFF timer enabled for a given number of seconds.
12
2
0
Parameter no. 12 - Turn Smart plug 16A On Automatically with Timer
If Smart plug 16A is OFF, you can schedule it to turn ON automatically after a period of time defined in this parameter. The timer is reset to zero each time the device receives an OFF command, either remotely (from the gateway (hub) or associated device) or locally from the switch. Values (size is 2 byte dec): • default value 0 • 0 - Auto ON Disabled 1 - 32535 = 1 - 32535 seconds. Auto ON timer enabled- for a given amount of seconds.
30
1
0
Parameter no. 30 - Restore on/off status for Smart plug 16A after power failure
This parameter determines if on/off status is saved and restored for the Smart plug 16A after power failure. Values (size is 1 byte dec): • default value 0 • 0 - Device saves last on/off status and restores it after a power failure. • 1 - Device does not save on/off status and does not restore it after a power failure, it remains off.
40
1
20
Parameter no. 40 – Watt Power Consumption Reporting Threshold for Smart plug 16A
Choose by how much power consumption needs to increase or decrease to be reported. Values correspond to percentages, so if 20 is set (by default), the device will report any power consumption changes of 20% or more compared to the last reading. Values (size is 1 byte dec): • default value 20 • 0 - Power consumption reporting disabled • 1 - 100 = 1% - 100% Power consumption reporting enabled. New value is reported only when Wattage in real time changes by more than the percentage value set in this parameter compared to the previous Wattage reading, starting at 1% (the lowest value possible). Power consumption needs to increase or decrease by at least 1 Watt to be reported, REGARDLESS of percentage set in this parameter. NOTE: When reporting Watts, module will automatically report also [V] (Voltage) and [A] (Amperes)
42
2
0
Parameter no. 42 – Watt Power Consumption Reporting Time Threshold for Smart plug 16A Load
Set value refers to the time interval with which power consumption in Watts is reported (30 – 32535 seconds). Values (size is 2 byte dec): • default value 0 • 0 - Power consumption reporting on time interval disabled • 30 - 32535 = 30 - 32535 seconds. Power consumption reporting enabled. Report is sent according to time interval (value) set here. The device is reporting the following values (if there was a change): W, V and A. NOTE: The energy consumption (kWh) is reported regardless of the values, set in the parameters 40 and 42. The energy consumption will be reported, when it increases for at least 0,1 kWh.
50
2
30
Parameter no. 50 – Down value
Lower power threshold used in parameter no. 52. Values (size is 2 byte dec): • default value 30 = 30 W • 0 – 4000 = 0W – 4000 W Down value cannot be higher or equal to the value specified in parameter no. 51. If the set value is higher or equal to the value in parameter 51, the set command is ignored. NOTE: if parameter no. 50 value is 100W, if measured power is lower than 100W, the association is sent. Power threshold step is 1W
51
2
50
Parameter no. 51 – Up value
Upper power threshold used in parameter no. 52 Values (size is 2 byte dec): • default value 50 = 50 W • 0 – 4000 = 0 W – 4000W Up value cannot be lower or equal to the value specified in the parameter no. 50. If the set value is lower or equal to the value in parameter 50, the set command is ignored. NOTE: If parameter no. 51 value is 200W. If measured power is higher than 200W the association is sent. Power threshold step is 1W.
52
1
6
Parameter no. 52 - Action in case of exceeding defined power values (parameters 50 and 51)
Parameter defines the way 3rd association group devices are controlled, depending on the current power load Values (size is 1 byte dec): • default value 6 • 0 – function inactive • 1 – turn the associated devices on, once the power drops below Down value (parameter no. 50) • 2 – turn the associated devices off, once the power drops below Down value (parameter no. 50) • 3 – turn the associated devices on, once the power rises above Up value (parameter no. 51) • 4 – turn the associated devices off, once the power rises above Up value (parameter no. 51) • 5 – 1 and 4 combined. Turn the associated devices on, once the power drops below Down value (parameter no. 50). Turn the associated devices off, once the power rises above Up value (parameter no. 51). • 6 – 2 and 3 combined. Turn the associated devices off, once the power drops below Down value (parameter 50). Turn the associated devices on, once the power rises above Up value (parameter no. 51).
70
2
0
Parameter no. 70 - Overload safety switch
The function allows for turning off the controlled device in case of exceeding the defined power for more than 3 seconds. Controlled device can be turned back on by S-button or sending a control frame. By default this function is inactive. Values (size is 2 byte dec): • default value 0 • 1 – 4000 = 1 W – 4000W • 0 = function not active NOTE: This functionality is not an overload safety protection, please check installation note for details. In case of overload the following message will be send towards the controller: • COMMAND_CLASS_NOTIFICATION_V5 • The Alarm V1 type field set to 0x00 • Notification Type 0x08 and 0x08 (Overload detected) NOTE: Regardless of the value set in this parameter the overcurrent protection is always active and can not be disabled.
71
2
0
Parameter no. 71 – Power threshold
This functions allows setting the power threshold for triggering the Program started notification. When the threshold will be reached the notification will let the user know that the device connected to the smart plug started working. Values (size is 2 byte dec): • default value 0 • 1 – 4000 = 1 W – 4000W • 0 = function not active When the threshold is reached the following message will be send towards the controller: • COMMAND_CLASS_NOTIFICATION_V5 • The Alarm V1 type field set to 0x00 • Notification Type 0x0C and 0x01 (Program started)
72
1
1
Parameter no. 72 – Time interval
This function allows setting the time interval for triggering the Program completed notification. When the active power will fall below the power threshold set in parameter 71, the time interval will start and when it will expire the notification will let the user know that the device connected to the smart plug finished working. The time interval is useful for the devices that have pause intervals during operations. Values (size is 1 byte dec): • default value 1 • 0 – 125 = 0 – 125 minutes • 0 = immediate sending of notification when active power drops bellow threshold set in parameter 71 When the the time interval expires the following message will be send towards the controller: • COMMAND_CLASS_NOTIFICATION_V5 • The Alarm V1 type field set to 0x00 • Notification Type 0x0C and 0x03 (Program completed)
73
1
1
Parameter no. 73 – Turn Smart Plug OFF
This function allows turning the Smart Plug output to OFF once the time interval is expired and the Program completed notification is sent to the controller. Values (size is 1 byte dec): • default value 0 • 0 – function disabled • 1 – turn OFF relay once the notification Program completed is sent
74
1
1
Parameter no. 74 – Enable/disable LED
This function allows enabling or disabling the Smart Plug LED. In case the user doesn’t want the LED indicator he can turn it OFF with this parameter. NOTE: if an overload or overcurrent occurs the red LED will still turn ON regardless of the value set in this parameter. Values (size is 1 byte dec): • default value 1 • 0 – LED is disabled • 1 – LED is enabled
Basic V2
COMMAND_CLASS_BASIC_V2
Association Group Information V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic V2
COMMAND_CLASS_BASIC_V2
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V4
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V4
COMMAND_CLASS_METER_V4
Notification V5
COMMAND_CLASS_NOTIFICATION_V5
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Supervision
COMMAND_CLASS_SUPERVISION
Switch Binary V2
COMMAND_CLASS_SWITCH_BINARY_V2
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Exclusion
REMOVAL FROM A Z-WAVE NETWORK (Z-WAVE EXCLUSION)

1. Connect the device to the power supply

2. Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion

3. Enable add/remove mode on your Z-Wave gateway (hub)

4. Press and hold the Service button S from 2 to 6 seconds (with holding the S button for the interval between 2 and 6 seconds you put the device in EXCLUSION MODE)

5. The device will be removed from your network, but any custom configuration parameters will not be erased
Inclusion
AUTOMATICALLY ADDING THE DEVICE TO A Z-WAVE NETWORK (AUTO INCLUSION)

1. Enable add/remove mode on your Z-Wave gateway (hub)

2. Automatic selection of secure/unsecure inclusion

3. The device can be automatically added to a Z-Wave network during the first 2 minutes

4. Connect the device to the power supply

5. Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the device will automatically enrol in your network (when the device is excluded and connected to the power supply it automatically enters the INCLUSION MODE state.)
Factory Reset
FACTORY RESET

• The reset is only possible the first minute after the power on

• Press and hold the service button S more than 6 seconds

• The device will be removed from your network and the led will start blinking. The device is now in its factory default state.

• When the S button is held more than 6 seconds after the first minute is passed, the relay should not react!



By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted. Use this reset procedure only when the main gateway (hub) is missing or otherwise inoperable.
Additional Special Features
1. Qubino Smart Plug 16A supports S2 Authenticated security.

2. Smart Plug 16A can automatically turn devices/lights on or off after a set period of time. Independent of other scenes and gateway (hub) commands.
S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
IP (Ingress Protection) Rated
Product is suitable for Outdoor use and is waterproof under an IP (Ingress Protection) rating system.
Outdoor Use
Product is suitable for use outdoors.
Color
If the product is only available in one color, pick the color from the list.
Supported Meter Type
Indicate which type of metering is supported by the device.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps
Switch Load Capacity Watts
The amount of switch load energy the product is rated for in Watts

 

Reviews

Grade 
07/13/2020

Muy bien

Muy buen funcionamiento con Fibaro. Necesitaba una maniobra de 16A y creo que esta es muy buena opción

Grade 
04/3/2019

16 amperios de enchufe

Lo utilizo para un termo de 3400W y va genial. Pequeño pero matón. Gracias.

  • 1 out of 1 people found this review useful.
Grade 
03/12/2019

Muy potente

Bastante pequeño para la potencia que soporta. Muy discreto en enchufe de pared para mis radiadores electricos.

Write your review!

Write a review

Qubino Smart Plug 16A - Small size Z-Wave Plus on-off wallplug

Qubino Smart Plug 16A - Small size Z-Wave Plus on-off wallplug

Smart wallplug with consumption measurement. The smallest 16A Z-Wave plug on the market. With Z-Wave Plus technology and consumption measurement. It does not limit the power of the plug to which we connect the smart plug since these are usually 16 amps, like this SmartPlug 16A of Qubino.

10 other products in the same category:

Customers who bought this product also bought: