Wall thermostat with Secure LCD screen

1

1

Z-Wave Plus Lifeline group, SRT321 will send unsolicited Battery Level Report, Thermostat Set Point Report and unsolicited Multilevel Sensor Report to lifeline group.

2

4

Nodes controlled by Thermostat Mode SET command.

3

4

Nodes controlled by Switch Binary SET command.

4

4

Nodes to receive unsolicited Battery Level Reports or Low Battery Warnings.

5

4

Nodes to receive Thermostat Set Point Reports.

6

4

Nodes to receive unsolicited Multilevel Sensor Reports.

1

1

255

Enables Temperature Sensor

controls the use of the temperature sensor on the device

2

1

0

Temperature Scale

Sensor will report temperature in this scale

3

1

10

Delta Temperature

defines the temperature steps of the heating control value is 0.1˚C. (e.g. to configure 2˚C delta temperature write 2*10 = 20)

Switch Binary

COMMAND_CLASS_SWITCH_BINARY

Thermostat Mode

COMMAND_CLASS_THERMOSTAT_MODE

Exclusion

STEP 1: On the SRT321, Set DIL switch 1 on the back of the unit to 'ON' position, scroll through the function menu by rotating the dial, select ""E"" and press the dial to activate Exclusion process. Now the character ""E"" starts flashing.

STEP 2: On the 3rd party device, select Exclusion for removing device from SRT321's network.

After successful Exclusion SRT321 displayed ""EP"" other wise displayed ""EF"" (Exclusion fail).

Note: Once the character starts flashing the installer has 60 seconds to activate the 3rd party device.

After successful Exclusion set DIL switch 1 to 'OFF' position to operate SRT321 in normal operation.

If the Exclusion process has failed more than once, try moving the SRT321 to another position and repeat the Exclusion steps.

Inclusion

STEP 1: On the SRT321, set DIL switch 1 on the back of the unit to 'ON' position, scroll through the function menu by rotating the dial, select ""I"" and press the dial to activate Inclusion process. Now the character ""I"" starts flashing.

STEP 2: On the 3rd party device, select Inclusion for adding a device into SRT321's network.

After successful inclusion SRT321 displayed ""IP"" other wise displayed ""IF"" (Inclusion fail).

Note: Once the character starts flashing the installer has 60 seconds to activate the 3rd party device.

After successful Inclusion set DIL switch 1 to 'OFF' position to operate SRT321 in normal operation.

If the inclusion process fails more than once, the 3rd party device may be already included in another network. So first exclude and then include the device.

Factory Reset

Please use this procedure only when the primary controller is missing or otherwise inoperable.

To reset the thermostat Set DIL switch 1 on the back of the unit to 'ON' position, scroll through the function menu by rotating the dial, select ""P"" and press the dial twice on the target device to execute reset.

Note: After successful operation device displayed ""PP"".

It will put the device in factory default, that include setting all the configuration, Association to factory default and removing the device from Z-Wave network.

Learn Mode (adding another controller)

STEP 1: On the another Z-Wave controller, select Include for adding SRT321 to the network.

STEP 2: On the SRT321, Set DIL switch 1 on the back of the unit to 'ON' position, scroll through the function menu by rotating the dial, select ""L"" and press the dial to start Learn process. Now the character ""L"" starts flashing.

After successful operation SRT321 displayed ""LP"" other wise displayed ""LF"" (Learn fail).

Note: Once the character starts flashing the installer has 20 seconds to activate the 3rd party controller unit (2 seconds classic inclusion, than after 3 retries for NWI inclusion).

After successful Learn set DIL switch 1 to 'OFF' position to operate SRT321 in normal operation.

If the Learn process has failed more than once, the SRT321 may be already included in another network. So first exclude and then include the SRT321.

Device Wake-Up

SRT321 will wake-up regularly and announce the wakeup state by sending Wakeup Notification to the configured node ID if Wakeup Interval and valid node ID is set.

To forcefully wake up the device to send Wakeup notification do the following steps: Set DIL switch 1 on the back of the unit to 'ON' position, and than back to the 'OFF' position.

Note: It is possible to set the node ID to 255 to send wakeup notifications as broadcast. In this mode device takes more time to go to sleep and drains battery faster, but can notify all it's direct neighbors about a wakeup.