Viewed products





Confianza Online


Aeotec aërQ - Z-Wave + 700 temperature and humidity sensor

ZWA009-C

New

1 small sensor. 4 main measurements built into any Z-Wave system that automates heating, cooling or air health.

More details

Out of stock

34,99 €

Technical characteristics

Technology Z-Wave Plus

More info

Precise air management

The Aeotec aërQ is a small sensor that monitors critical measurements of the indoor environment.

Temperature

Manage heating and cooling and maintain a perfectly tempered space; aërQ technology monitors and reports temperatures between -10 ° C and 65 ° C and with an accuracy of ± 1 ° C.

Humidity

Whether to manage air flow in living spaces or steam in showers, aërQ technology allows the relative humidity of a space to be measured between 0% and 80% and with an accuracy of ± 3%.

Dew

Comfort and dew point go hand in hand. Too low and the skin can become irritated. Too high and you won't cool off on a hot day. AërQ technology measures the dew point of a room in the same range as its relative humidity.

Mold

A compatible home automation controller can use aërQ technology to check for poor air quality and warn of the likelihood of mold spores.

Install it (almost) anywhere

Comprehension and intelligence, wherever you need it. The aërQ temperature and humidity sensor is small. Really small. At 35mm wide, it is barely wider than a button battery. It is designed this size to fit almost anywhere you need to measure temperature and humidity and analyze certain attributes of air health. Its precision and focus allow you to improve the measurements your automation systems receive from other sensors, while its size allows you to discreetly install multiple sensors in large rooms.

Measurement and understanding

Once paired with a compatible Z-Wave controller, you can monitor room temperature, humidity and health anytime, anywhere.

Measurement and automation

The aërQ temperature and humidity sensor is more than just information. Fully compatible Z-Wave controllers will allow you to exploit your measurements and analysis, using multiple data points and conclusions to enable powerful and intelligent automation.

Cool or heat a space to make it perfect. Automatically.

Set and automate your desired climate and turn on connected ventilation, air conditioning or heating when the temperature of a space is deemed less than perfect.

Moisten a space when the air is too dry. Automatically.

Saunas must look like saunas, deserts, deserts. Controls the relative humidity in a room and automatically turns on connected humidifiers, dehumidifiers or extractors.

Adjust the air flow when the air quality is poor. Yes, automatically.

Turn on the fans and open the windows automatically or reactively when the aërQ temperature and humidity sensor warns you of poor air quality and the risk of mold growth.

1 battery. Shelf life 2 years.

A single button cell keeps measuring for years. With precision.

Engineered in Germany around a unique and inexpensive CR2477 button cell, the aërQ temperature and humidity sensor uses Z-Wave's ultra-low-power Gen7 and S2 technologies, allowing it to work for up to 2 years before needing to be replaced. your stack. And changing the battery is child's play: you just have to separate the two parts, recycle the existing battery and insert a new one. The aërQ temperature and humidity sensor will be in place and will be measuring again in no time.

FUNCTIONS:

Measure temperature and humidity
Measure the dew point
Indicates risk of humidity
Supports 6 groups of associations
Up to 2 years of battery life
Z-Wave Smart Start and S2 Security
Wireless technology: Z-Wave Plus V2 (Z-Wave 700 / Gen7)

TECHNICAL DATA:

Power supply: CR2477 3V lithium battery (LiMnO2)
Battery life: with default settings, up to 2 years
Radio frequency: 868.42 MHz
Operating distance: up to 150 meters outdoors / more than 50 meters indoors
Humidity range: 0 to 80% RH + - 3%.
Temperature range: -10 to 65 ° C (+ - 1 ° C)
Dew point range: -10 to 65 ° C (+ - 1 ° C)
Operating humidity: 10 to 95%.
Operating temperature: 0 ° C to 45 ° C
Storage temperature: -30 ° C to 70 ° C
Dimensions: 35 x 35 x 18 mm
Weight: 21g

Extended Z-Wave info

Name: AërQ - Temperature & Humidity Sensor
Manufacturer:Aeotec
Identifier:ZWA009-C
Z-Wave Certification Number:ZC12-20080086
Hardware Plattform:ZGM130
FLiRS:NO
Role Type:Reporting Sleeping Slave
Short Description:Monitor climate and analyse air health with the AërQ sensor.
Description:The AërQ is an intelligent sensor to monitor your environment at home. It measures temperature and humidity. Via an intelligent analysis, the sensor protects your health by detecting the danger of mould formations.

Manual download HERE.

Group
Max Nodes
Description
1
5
Lifeline Association to Gateway
2
5
High Temperature Notification - Sends a notification to the associated device
3
5
Low Temperature Notification - Sends a notification to the associated device, when the low temperature threshold is breached.
4
5
High Humidty Notification - Sends a notification to the associated device, when the high humidity threshold is breached.
5
5
Low Humidty Notification - Sends a notification to the associated device, when the low humidity threshold is breached.
6
5
Air Temperature (A multilevel sensor report is sent to the nodes in this group).
Number
Size (Bytes)
Default Value
Name
Description
1
1
20
Minimum Temperature change to report
This value defines the minimum change of temperature to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the temperature changes. However, periodic reports, managed by configuration parameter 4, may still be active.
10
1
0
High Temperature Trigger BASIC Set Command Value
This defines what BASIC command shall be sent out into association group 2
11
1
255
Low Humidity Trigger BASIC Set Command Value
This defines what BASIC command shall be sent out into association group 5
12
1
0
High Humidity Trigger BASIC Set Command Value
This defines what BASIC command shall be sent out into association group 4
13
1
0
Offset value for Mould danger notification
This value allows to increase the humidity threshold for mold danger notification by max 10%
2
1
5
Minimum humidity change to report
This value defines the minimum change of humidity to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the humidity changes. However, periodic reports, managed by configuration parameter 4, may still be active.
255
4
0
Reset parameter
This parameter helps reset configuration parameters and the device to factory defaults.
4
2
43200
Temperature and Humidity Periodic Reports
This parameter defines the time interval to send an unsolicited report. If the value is set to 0, there will be no periodic reports sent to the controller. However, reports on temperature/humidity changes, managed by configuration parameters 1 and 2, may still be active.
5
2
0
Temperature Upper Watermark value
This parameter defines a temperature. If the measured temperature surpasses this watermark a BASIC command is sent into Association Group 2
6
2
0
Temperature Lower Watermark value
This parameter defines a temperature. If the measured temperature drops below this watermark a BASIC command is sent into Association Group 3
7
1
0
Humidity Upper Watermark value
This parameter defines a relative humidity. If the measured relative humidity surpasses this watermark a BASIC command is sent into Association Group 4
8
1
0
Humidity Lower Watermark value
This parameter defines a relative humidity. If the measured temperature drops below this relative humidity a BASIC command is sent into Association Group 5
9
1
255
Low Temperature Trigger BASIC Set Command Value
This defines what BASIC command shall be sent out into association group 3
Association Group Information V3
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Battery
COMMAND_CLASS_BATTERY
Configuration V4
COMMAND_CLASS_CONFIGURATION_V4
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V5
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
Indicator V3
COMMAND_CLASS_INDICATOR_V3
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Notification V8
COMMAND_CLASS_NOTIFICATION_V8
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S2
COMMAND_CLASS_SECURITY_2
Sensor Binary V2
COMMAND_CLASS_SENSOR_BINARY_V2
Sensor Multilevel V11
COMMAND_CLASS_SENSOR_MULTILEVEL_V11
Supervision
COMMAND_CLASS_SUPERVISION
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V3
COMMAND_CLASS_VERSION_V3
Wake Up V2
COMMAND_CLASS_WAKE_UP_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Classic Inclusion
Inclusion

1. Insert the battery.

2. Press the button quickly three times in a row.
Classic Exclusion
Exclusion

1. Press the button quickly three times in a row.
Wake-Up Procedure
A click on the central button will wake up the device.
Factory Reset Procedure
Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

Keep the button pressed for 10 seconds. After 5 seconds the red LED will start blinking.
Where to find S2 DSK on product
To run this device please insert fresh 1 * CR2477 batteries. Please make sure the internal battery is fully charged. Triple clicking the central button includes (adds) and excludes (removes) the device. A click on the central button will wake up the device. The device supports the Security S2 framework with unauthenticated and authenticated network keys. The DSK for the S2 inclusion can be found inside the sensors packaging. Please follow the instructions on the central controller when including.

The device also supports Smart Start. Please scan the QR code on the outlet cover of the device and your controller will add the device automatically when powered up.
S2 Authenticated
S2_AUTHENTICATED
S2 Unauthenticated
S2_UNAUTHENTICATED
Color
If the product is only available in one color, pick the color from the list.
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.
Battery Quantity
Enter the number of batteries of the designated type that the product uses.

 

Reviews

Write a review

Aeotec aërQ - Z-Wave + 700 temperature and humidity sensor

Aeotec aërQ - Z-Wave + 700 temperature and humidity sensor

1 small sensor. 4 main measurements built into any Z-Wave system that automates heating, cooling or air health.

21 other products in the same category: