Viewed products





Confianza Online


ZIPATO - Indoor siren Z-Wave+ multisounds

ZIP-AB02Z

New

The Zipato Z-Wave + indoor siren provides a light and sound alert for your installation.

More details

In Stock

44,09 €

-10%

48,99 €

Technical characteristics

Technology Z-Wave Plus

More info

This siren can be included and operated in a Z-Wave network with other certified devices

This siren integrates the sound alert and a light alert with a flash.

The design of the siren makes it easy to place on any wall or surface and can be powered by batteries or a mini 5V USB adapter.

FUNCTIONS:

Siren 115db
10 types of sounds
Z-Wave +
Self-protection contact
Easy to install
Low energy consumption

Technical characteristics :

Protocol: Z-Wave +
Power supply: 2 x CR123A or Mini-USB 5V
Frequency: 868.42 MHz
Range radius: 40m in free field.
Volume of the siren: 115dB
Operating temperature: 0 ° C to 40 ° C.
Dimensions: 70 x 98 x 31 mm.
Certifications: CE and RoHS.

Extended Z-Wave info

Name: Siren alarm EU
Manufacturer:Zipato
Identifier:ne-nas-ab02z.eu
Z-Wave Certification Number:ZC10-18096228
Hardware Plattform:ZM5202
FLiRS:YES
Role Type:Listening Sleeping Slave
Short Description: Multi sound siren which can be used with any Z-Wave gateway.
Description: Alerts you if an intruder tries to get into your home through your doors or windows. · Set the siren and warning light to turn on when unexpected activity is detected. · Set up the siren so that it’s triggered automatically by your sensors and camera. Get smart alerts when doors or windows are opened unexpectedly or when motion is detected.

Manual download HERE.

Group
Max Nodes
Description
1
5
Z-Wave Plus Lifeline, reports relay’s status to just one device, Z-wave network’s main controller by default. It’s not recommended to modify settings of this association group.
2
5
is assigned to the siren status - ON/OFF. Allows for sending a controlled command to the associated device whenever the Indoor siren is turned ON (or OFF).
Number
Size (Bytes)
Default Value
Name
Description
1
1
2
Configure alarm volume
This parameter defines the output volume when siren plays alarm. Doorbell alarm volume has three settings, Low (Parameter is set to ‘1’), Middle (Parameter is set to ‘2’), High (Parameter is set to ‘3’). The default value is ‘2’.
2
1
2
Configure alarm duration time
This Parameter defines the alarm duration time when siren receives an alarm sensor notification report or an alarm command from controller. Siren duration time has three settings: 30 seconds (Parameter is set to ‘1’), 1 minute (Parameter is set to ‘2’), 5 minute (Parameter is set to ‘3’). The default value is ‘2’.
3
1
1
Configuring doorbell music duration time
This parameter defines the doorbell music duration time when siren receives a door/window sensor notification report or an alarm command (BASIC_SET =0x02) from a controller. The doorbell music will be played always if this parameter is set to ‘0’. The doorbell music will not be played if this parameter is set to ‘-1’. Other values are the doorbell music playing duration time. Unit: Time.
4
1
2
Configure doorbell music volume
This parameter defines the output volume when siren plays doorbell music. Doorbell music volume has three settings: Low (Parameter is set to ‘1’), Middle (Parameter is set to ‘2’), High (Parameter is set to‘3’). The default value is ‘2’.
5
1
9
Configure alarm sound index
This parameter defines the alarm sound index so siren can play different sound when an alarm occurs. There are 10 different sounds for user selection.
6
1
10
Configure doorbell music index
This parameter defines the doorbell music index so siren can play different music when an alarm occurs. There are 10 different music compositions for user selection.
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic V2
COMMAND_CLASS_BASIC_V2
Battery
COMMAND_CLASS_BATTERY
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Indicator
COMMAND_CLASS_INDICATOR
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Notification V8
COMMAND_CLASS_NOTIFICATION_V8
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S2
COMMAND_CLASS_SECURITY_2
Supervision
COMMAND_CLASS_SUPERVISION
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V3
COMMAND_CLASS_VERSION_V3
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Factory Reset
Reset procedure will remove all information on the Z-Wave network or Z-Wave controller and restore the sensor to factory default settings. Please use this procedure only when the network primary controller is missing or otherwise inoperable.



1) Remove the sensor’s cover

2) Make sure the sensor is connected to power source

3) Press the code button for 10 seconds, LED will flash blue for 3 seconds

4) Release the code button



Note:

When the siren is being restored to factory settings, please make sure power source is connected.

Additional Special Features
1. Configure alarm volume

This parameter defines the output volume when siren plays alarm. Doorbell alarm volume has three settings, Low (Parameter is set to ‘1’), Middle (Parameter is set to ‘2’), High (Parameter is set to ‘3’). The default value is ‘2’.



2. Configure alarm duration time

This Parameter defines the alarm duration time when siren receives an alarm sensor notification report or an alarm command from controller. Siren duration time has three settings: 30 seconds (Parameter is set to ‘1’), 1 minute (Parameter is set to ‘2’), 5 minute (Parameter is set to ‘3’). The default value is ‘2’.



3. Configuring doorbell music duration time

This parameter defines the doorbell music duration time when siren receives a door/window sensor notification report or an alarm command (BASIC_SET =0x02) from a controller. The doorbell music will be played always if this parameter is set to ‘0’. The doorbell music will not be played if this parameter is set to ‘255’. Other values are the doorbell music playing duration time. Unit: Time.



4. Configure doorbell music volume

This parameter defines the output volume when siren plays doorbell music. Doorbell music volume has three settings: Low (Parameter is set to ‘1’), Middle (Parameter is set to ‘2’), High (Parameter is set to‘3’). The default value is ‘2’.



5. Configure alarm sound index

This parameter defines the alarm sound index so siren can play different sound when an alarm occurs. There are 10 different sounds for user selection.



6. Configure doorbell music index

This parameter defines the doorbell music index so siren can play different music when an alarm occurs. There are 10 different music compositions for user selection.



Note The alarm sounds are very loud and can damage your hearing. During acoustic alarm, please keep sufficient distance to the siren and protect your hearing.



Battery check command

Users can also inquire the battery status of the siren by sending BATTERY_GET command. Once the siren receives the command, it will return BATTERY_ REPORT command. The siren will send BATTERY_ LEVEL=0xFF command to the Z-Wave Controller to inform that the siren is in dead battery status, otherwise BATTERY_LEVEL value range is 0% to 100%.



Command Classes

This Sensor supports Command Classes as Below:

* COMMAND_CLASS_ZWAVEPLUS_INFO (V2)

* COMMAND_CLASS_VERSION (V2)

* COMMAND_CLASS_MANUFACTURER_SPECIFIC (V2) * COMMAND_CLASS_DEVICE_RESET_LOCALLY (V1) * COMMAND_CLASS_POWERLEVEL (V1)

* COMMAND_CLASS_BATTERY (V1)

* COMMAND_CLASS_ASSOCIATION (V2)

* COMMAND_CLASS_ASSOCIATION_GRP_INFO (V1) * COMMAND_CLASS_WAKE_UP (V2)

* COMMAND_CLASS_SWITCH_BINARY (V1)

* COMMAND_CLASS_NOTIFICATION (V4)

* COMMAND_CLASS_CONFIGURATION (V1)
Inclusion
The indoor siren can be included to the Z-Wave network by pressing the code button.

1) Disassemble the siren and insert the battery into

the siren. Make sure the device is located within

the direct range of the controller.

2) Set the controller into the inclusion mode (see

main controller’s operating manual).

3) Quickly triple click the code button, LED light will

flash red for 5 times.

4) The Indoor siren will be detected and included

in the Z-Wave network.

5) Wait for the main controller to configure the siren.



SMART START. This product also supports Z-Wave Smart Start option which enables easier inclusion. QR code for SmartStart inclusion is printed on the battery cover. SmartStart option is only possible when network controller is also supporting SmartStart.
Exclusion
1) Make sure the siren is connected to power source. 2) Set the main controller into the exclusion mode

(see main controller’s operating manual).

3) Quickly triple click the code button, LED light

will flash red for 5 times

4) Wait for the main controller to remove the sensor.
S2 Unauthenticated
S2_UNAUTHENTICATED
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).
Battery Quantity
Enter the number of batteries of the designated type that the product uses.
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.

 

Reviews

Write a review

ZIPATO - Indoor siren Z-Wave+ multisounds

ZIPATO - Indoor siren Z-Wave+ multisounds

The Zipato Z-Wave + indoor siren provides a light and sound alert for your installation.

11 other products in the same category:

Customers who bought this product also bought: