Multisensor 4 en 1 Z-Wave de ZIPATO PIR (Movimiento) + Puerta / Ventana + luminosidad + temperatura

Technical characteristics

Technology	Z-Wave Plus

More info

This multi-sensor Zipato elegant design has multiple home automation functions. It is called "QUAD MODOLITE". Thus, it has detection PIR (Motion Detector), door / window (magnetic contact), temperature and brightness, 4 sensors in a single integrated and compact device, based on Z-Wave Plus technology.

Detects temperature rises, changes in brightness, movement (PIR), and opening of doors or windows

Frequency: 868.42 / 908.42Mhz

Dimensions:

Sensor: 28 x 96 x 23 mm
Magnet: 10 x 50 x 12 mm

characteristics

"(1) door / window detector (2) PIR (3) Iuminosity and (4) temperature, in one sensor
"It has chip of the series 400 Z-Wave, with support of multiple channels and greater speed of data (9.6 / 40 / 100kbps)
"(Output power + 2.5dBm compared to the 300 series -2.5dBm Z-Wave module), superior output power to improve communication range
"Brightness range: 0-500 lx
"Operating temperature: -10 ~ 40 ° C. Only for indoor use.
"CR123A lithium battery 1500mA to guarantee battery life 2 years
"Recessed light sensor, while applied to control brightness
"PIR detection angle: 90 °
"PIR detection range: from 8 to 10m
"Weight: approx 52gr
"Protection against sabotage and manipulations (Tamper)
"Easy to install
"Low battery indicator
"Z-Wave Plus
"Part 15.249 FCC / EN300 220-1 / certification
"NCC

Extended Z-Wave info

Name: Multisensor QUAD - MODOLITE, Z-wave

Manufacturer:Zipato

Identifier:ph-psm02.eu

Z-Wave Certification Number:ZC10-17065644

Hardware Plattform:SD3502

FLiRS:NO

Role Type:Reporting Sleeping Slave

Short Description:Zipato Multisensor Quad offers elaborate security and ambient sensing options.

Description:Zipato Multisensor Quad offers elaborate security and ambient sensing options. Multifunctional nature of this product allows you to detect motion, monitor opened/closed status of any opening object, measure room’s ambient temperature and light intensity.

Manual download HERE.

Group

Max Nodes

Description

1

8

Z-Wave Plus Lifeline

2

8

Lighting group control

Number

Size (Bytes)

Default Value

Name

Description

10

1

12

Auto Report Battery Time

The interval time for auto report the battery level. 0 means turn off auto report battery. The default value is 12. The tick time can setting by the configuration No.20.

11

1

12

Auto Report Door/ Window State Time

The interval time for auto report the door/ window state. 0 means turn off auto report door/window state. The default value is 12. The tick time can setting by the configuration No.20.

12

1

12

Auto Report Illumination Time

The interval time for auto report the illumination. 0 means turn off auto report illumination. The default value is 12. The tick time can setting by the configuration No.20.

13

1

12

Auto Report Temperature Time

The interval time for auto report the temperature. 0 means turn off auto report illumination. The default value is 12. The tick time can setting by the configuration No.20.

2

1

-1

Basic Set Level

Setting the BASIC command value to turn on the light. The 0xFF(-1) means turn on the light. For dimmer equipment 1 to 100 means the light strength.

20

1

30

Auto Report Tick Interval

The interval time for auto report each tick. Setting this configuration will effect configuration No.10, No.11, No.12 and No.13. Caution: Setting to 0 means turn off all auto report function.

21

1

Temperature Differential Report

The temperature differential to report. 0 means turn off this function. The unit is Fahrenheit. Enable this function the device will detect every minutes. And when the temperature is over 140 degree Fahrenheit, it will continue report. Enable this functionality will cause some issue please see the detail in the “Temperature Report” section.

22

1

0

Illumination Differential Report

The illumination differential to report. 0 means turn off this function. The unit is percentage. Enable this function the device will detect every minutes. Enable this functionality will cause some issue please see the detail in the “Illumination Report” section.

3

1

80

PIR Sensitivity

PIR sensitivity settings. 0 means disable the PIR motion. 1 means the lowest sensitivity, 99 means the highest sensitivity. High sensitivity means can detected long distance, but if there is more noise signal in the environment, it will re-trigger too frequency.

4

1

99

Light Threshold

Setting the illumination threshold to turn on the light. When the event triggered and the environment illumination lower then the threshold, the device will turn on the light. 0 means turn off illumination detected function. And never turn on the light. 1 means darkest. 99 means brightest. 100 means turn off illumination detected function. And always turn on the light. Notice: In none test mode, only the value in 1 to 99 will enable the illumination detected function and update the illumination value.

5

1

0

Operation Mode

Operation mode. Using bit to control.

6

1

4

Multi-Sensor Function Switch

Multisensor function switch. Using bit to control.

7

1

4

Customer Function

Customer function switch, using bit control.

8

1

3

PIR Re- Detect Interval Time

In the normal mode, after the PIR motion detected, setting the re-detect time. 8 seconds per tick, default tick is 3 (24 seconds). Setting the suitable value to prevent received the trigger signal too frequently. Also can save the battery energy.

9

1

4

Turn Off Light Time

After turn on the lighting, setting the delay time to turn off the lighting when the PIR motion is not detected. 8 seconds per tick, default tick is 4 (32 seconds). 0 means never send turn off light command.

Basic

COMMAND_CLASS_BASIC

Association Group Info

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association V2

COMMAND_CLASS_ASSOCIATION_V2

Battery

COMMAND_CLASS_BATTERY

Configuration

COMMAND_CLASS_CONFIGURATION

Device Reset Locally

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Firmware Update Meta-Data V2

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

Manufacturer Specific V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Multi-Command

COMMAND_CLASS_MULTI_CMD

Notification V4

COMMAND_CLASS_NOTIFICATION_V4

Powerlevel

COMMAND_CLASS_POWERLEVEL

Security S0

COMMAND_CLASS_SECURITY

Sensor Binary V2

COMMAND_CLASS_SENSOR_BINARY_V2

Sensor Multilevel V5

COMMAND_CLASS_SENSOR_MULTILEVEL_V5

Version V2

COMMAND_CLASS_VERSION_V2

Wake Up V2

COMMAND_CLASS_WAKE_UP_V2

Z-Wave Plus Info V2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Device Wake-Up

If the user want to wake-up the device immediately, please remove

the front cover, and press the tamper key once. The device will

wake-up 10 seconds.

Inclusion

Put the Z-Wave Controller in inclusion mode. Pressing tamper key three times within 1.5 seconds will enter inclusion mode.

After successful inclusion, the device will wake to receive the

setting command from Z-Wave Controller in about 20 seconds.

Exclusion

Put the Z-Wave Controller in exclusion mode. Pressing tamper key three times within 1.5 seconds will enter exclusion mode. Node ID has been excluded.

Factory Reset

Use this procedure only in the event that the primary controller

is lost or otherwise inoperable.

Pressing tamper key four times within 1.5 seconds and during

4th press, hold the tamper key until LED lights up. After 3 seconds the LED will turn OFF, and after next 2 seconds, release the tamper key. If successful, the LED will light ON for one second. Otherwise, the LED will flash once.IDs are excluded and all settings will reset to factory default.

Battery Type

Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.

Color

If the product is only available in one color, pick the color from the list.

Sensors

Sensor types supported by the product.

Supported Notification Types

Select the Notification Types that the product handles (controllers), or sends (slaves).

Battery Quantity

Enter the number of batteries of the designated type that the product uses.