Viewed products





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

Sensor PIR Z-Wave Plus - Gen5 by Vision

VISEZP3102-5

New

Motion sensor technology Z-Wave Plus (passive infrared receiver -> PIR) allows detecting the presence of a person in a room or stay and based on this realizarrt domotic actions

More details

In Stock

46,49 €

Technical characteristics

Technology Z-Wave Plus

More info

This sensor of movement Z-Wave Plus of Vision (PIR = passive infrared receiver) detects presence in the rooms where it is located. The unit sends information to a Z-Wave Control Unit or to another associated Z-Wave device. Up to 4 devices can be controlled from this device. In addition to being a motion sensor, it also has the function of temperature sensor. It can be installed with screws or double-sided tape. The device is operated by batteries and remains in "sleep" mode until an action is detected. After a programmable time of inactivity, the device wakes up and sends a status signal. Then the unit returns to its state of "lethargy". The batteries can be replaced without the need to unscrew. The unit offers a visual alert on the device and sends an alert to the ZWave Control Unit when the battery needs to be changed. A "tamper" type switch protects the device for use in security environments, to protect it from tampering and sabotage. Lithium CR123 batteries last between 3 and 5 years under normal conditions of use. The device supports normal Z-Wave inclusion, auto inclusion and network inclusion, as appropriate. This device complies with the Z-Wave Plus (GEN5) certification.

Batteries, adhesive tape and instruction manual are included.

Note : When used with VERA, the temperature sensor is not available as a separate icon. This implies that LUA code has to be used to access and use the temperature value.

Extended Z-Wave info

Name: Motion Detector (with Temperature Sensor)
Manufacturer:Vision
Identifier:ZP3102EU-5
Z-Wave Certification Number:ZC10-14100005
Hardware Plattform:ZM5202
FLiRS:NO
Role Type:Reporting Sleeping Slave
Short Description:The ZP3102 is a Z-Wave enabled motion detector and temperature sensor.
Description:The ZP3102 is a Z-Wave enabled motion detector and temperature sensor. The motion detector has 120 degrees of horizontal visibility and 60 degrees of vertical visibility. The temperature sensor that is built in to the ZP3102 is capable of reporting in both Celsius and Fahrenheit scales, and may be queried for the temperature and it will report it automatically when it detects changes. The sensor is battery operated and includes the ability to report the battery level and will transmit an alert signal if the battery assumes a critically low level. The ZP3102 is future-proofed by also supporting the ability to have its firmware updated over the Z-Wave network.

Manual download HERE.

Group
Max Nodes
Description
1
5
Z-Wave Plus Lifeline
Number
Size (Bytes)
Default Value
Name
Description
1
1
3
Retriggering Time
User could set up the retriggering time from 1 ~ 255 minutes using values 0x00 to 0xFF (-128 to 127).
2
1
0
Temperature Scale
User could choose the temperature reported scale by following: 0x00 - Celsius 0x01 - Fahrenheit
3
1
4
Infrared sensor sensitivity
Infrared sensor sensitivity adjustment: 1 = most sensitive 7 = most insensitive
Basic
COMMAND_CLASS_BASIC
Exclusion
Put the Z-Wave Interface Controller into “exclusion” mode, and following its instruction to delete the ZP3102 to your Z-Wave network. Press the Program Switch of ZP3102 once to be excluded. The LED on the ZP3102 should start to flash.
Inclusion
Put the Z-Wave Interface Controller into 'inclusion' mode, and follow its instructions to add the ZP3102 to your Z-Wave network. For a successful inclusion, it is suggested to have the sensor and your Z-Wave controller about one meter apart. Press the Program Switch of the ZP3102 (refer to the manual for the location of the program switch) ready the ZP3102 for inclusion into the Z-Wave network. If inclusion does not take place or is unsuccessful within 20 seconds, the ZP3102 will go to sleep; if this happens, simply repeat pressing the program switch to try again.
Device Wake-Up
Remove the rear cover to wake up the device, or set the wake up interval time from 10 minutes to 1 week. The battery will be drained quickly if you fail to replace the cover after using that method to wake up the device.
Factory Reset
Removing the rear cover to wake up the device. Press Program Switch 10 times within 10 seconds, ZP3102 will go back to factory default. (This is to be used only in the case of the primary controller being inoperable or otherwise unavailable.)

 

Reviews

Grade 
11/26/2017

Sensor PIR

Como sensor de movimiento funciona bien, pero como sensor de temperatura es poco preciso va en escalones de unos 2 grados.

  • 1 out of 1 people found this review useful.

Write your review!

Write a review

Sensor PIR Z-Wave Plus - Gen5 by Vision

Sensor PIR Z-Wave Plus - Gen5 by Vision

Motion sensor technology Z-Wave Plus (passive infrared receiver -> PIR) allows detecting the presence of a person in a room or stay and based on this realizarrt domotic actions

Customers who bought this product also bought: