Viewed products





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

Smart Switch Aeotec Heavy Duty Smart Switch for high load with consumption measurement Z-Wave Plus (GEN5)

AEO_ZW078-ZWEU

New

Smart switch Aeotec Heavy Duty Smart Switch Z-Wave Plus (GEN5) by AEON LABS for large loads and high power (heavy duty)

More details

In Stock

119,95 €

Technical characteristics

Technology Z-Wave Plus
Characteristic Consumption Measurement

More info

It is a switch Z-Wave Plus (GEN5), intelligent, from the manufacturer AEON LABS suitable for large loads (heavy duty) up to 40 amps.

Smart switch Z-Wave Plus (GEN5) Aeotec by AEON LABS for large loads (heavy duty) is a switch module that will allow controlling devices or groups of devices with maximum loads of up to 9600W. You can control remotely or automatically through events or predefined home automation scenes through a Z-Wave Control Unit.

Thanks to its energy monitoring and planning features you can save on electricity immediately. You can receive reports of electric consumption in real time, you can plan and foresee the peaks of consumption, etc. thanks to its electric control and saving functions, up to a maximum of 40 amperes of electrical intensity.

Smart switch Z-Wave Plus (GEN5) from AEON LABS has Aeotec Gen5 technology, which surpasses the performance of everything known so far in Z-Wave. It is built according to the Z-Wave 500 series, offering improvements in radio performance of 50% and a communication speed of 250% faster than previous products with Z-Wave technology.

It is necessary to have a Z-Wave Control Unit to be able to integrate and control it from your Z-Wave network. This Z-Wave module works as if it were a wireless repeater with the other devices to favor the meshing of the Z-Wave network and increase coverage in the rooms.

FUNCTIONS:

  • Control remotely a device or group of devices connected to power circuits
  • ON / OFF function
  • Measurement of instantaneous and accumulated consumption.
  • Works for loads up to 40 amps maximum
  • Manufacture based on the Gen5 range of Aeon Labs
  • Security of communication via radio using AES-128 encryption
  • Integrates the Z-Wave technology of the 500 series
  • 250% faster communication compared to standard Z-Wave devices
  • Supports Z-Wave exploration frames
  • Supports Beaming
  • Firmware updates wirelessly: Over The Air (OTA)
  • Z-Wave message repeater
  • Optimization of antenna range up to 150 meters
  • Ease of use and installation

TECHNICAL CHARACTERISTICS :

  • Module type: Z-Wave Receiver (Z-Wave Plus)
  • Power supply: 240VAC, 50 / 60Hz
  • Consumption: 1W
  • Maximum load: 9600W / 40A
  • Frequency: 868.42 Mhz
  • Transmission distance: 200 m in open field
  • IP protection: IP43
  • Dimensions: 150mm x 118mm x 35mm
  • Weight: 350g
  • Operating temperature: 5-40 ° C
  • Moisture supported for operation: 80%
  • Certifications: FCC, UL, CE, ROHS
  • Fibaro HC Lite compatible Yes
  • Fibaro HC2 compatible Yes
  • Vera 3 / Lite compatible Yes
  • ZIPABOX compatible Yes
  • ZiBASE Pro compatible Yes
  • eedomus compatible Yes
  • ZiBASE Lite compatible Yes
  • Domoticz compatible Yes

Extended Z-Wave info

Name: Heavy Duty Smart Switch Gen5
Manufacturer:Aeotec
Identifier:ZW078-C
Z-Wave Certification Number:ZC10-14090016
Hardware Plattform:ZM5202
FLiRS:NO
Role Type:Always On Slave
Short Description:Heavy Duty Smart Switch Gen5 is an on/off switch module that also provides energy metering.
Description:Aeon Labs Heavy Duty Smart Switch is a Z-Wave device that can report the wattage energy usage and KWH usage to a Z-Wave Controller (especially a gateway), it can be controlled by other Z-Wave devices to turn on/off loads, it can bear up to 40A current of resister loads. It also acts as a repeater that forward Z-Wave command messages to destination nodes if the originating controller is out of range from the destination node. By taking advantage of the Z-Wave mesh network, commands can be routed to their destination via intermediary “listening” Z-Wave products. Products that are Z-Wave certified can be used and communicate with other Z-Wave certified devices.

Manual download HERE.

Group
Max Nodes
Description
1
5
Group 1 is assigned to the Lifeline association group and every device has 5 nodes to associate. When the switch is turned on or off using the action button, the switch will send a basic report of its status to the nodes in association group 1. To change what kind of signal is sent to the nodes in group 1, please see the detailed description of configuration parameter 80.
2
5
When the product receives a controlling Basic Set CC/Switch Binary Set CC/ Scene Activation Set CC, which if cause the product’s load state to be changed, which will lead to send the Basic Set CC/Switch Binary Set CC /Scene Activation Set CC to nodes in group 2.
Number
Size (Bytes)
Default Value
Name
Description
101
4
4
To set which report need to be sent.
This parameter is used to configure which reports need to be sent in Report Group 1. The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent. For example, instantaneous Current is the value 2 and instantaneous Watts is the value 4, so setting parameter 101 to a value of 6 will result in both instantaneous Current and instantaneous Watts to be reported. See the full description of the parameter values for other possible settings.
102
4
8
To set which report need to be sent.
This parameter is used to configure which reports need to be sent in Report Group 2. The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent. For example, instantaneous Current is the value 2 and instantaneous Watts is the value 4, so setting parameter 102 to a value of 6 will result in both instantaneous Current and instantaneous Watts to be reported. See the full description of the parameter values for other possible settings.
103
4
0
To set which report need to be sent.
This parameter is used to configure which reports need to be sent in Report Group 3. The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent. For example, instantaneous Current is the value 2 and instantaneous Watts is the value 4, so setting parameter 103 to a value of 6 will result in both instantaneous Current and instantaneous Watts to be reported. See the full description of the parameter values for other possible settings.
111
4
300
Set the interval time of sending report.
This parameter is used to set the interval time of sending report in Report Group 1. (The unit of time is second).
112
4
120
Set the interval time of sending report.
This parameter is used to set the interval time of sending report in Report Group 2. (The unit of time is second).
113
4
120
Set the interval time of sending report.
This parameter is used to set the interval time of sending report in Report Group 3. (The unit of time is second).
20
1
0
The load status after power on
This parameter is used for indicating the state of output load after re-power on.
200
1
0
Partner ID
This parameter is used to configure the partner ID. (0== Aeon Labs Standard Product, 1~255== others).
252
1
0
Enable/Disable Lock Configuration
This parameter is used to enable/disable Lock all configuration parameters. (0 =disable, 1 = enable)
255
4
0
Reset to default factory setting
This parameter is used to reset product to default factory setting. (There are just 2 values can be used).
3
1
0
Current Overload Protection
This parameter is used for the overload protection, which means the load will be disconnected after 5 seconds when the current more than 39.5A.
80
1
0
Enable/Disable to send notifications to associated devices to associated devices.
This parameter is used to Enable/Disable to send notifications to associated devices (in Group 1) when the state of Smart Switch Gen5’s load is changed. (0=Send nothing, 1=Send hail CC, 2=Send basic report CC).
90
1
1
Enable/Disable the function of parameter 91 and 92.
This parameter is used to Enable/Disable the function of parameter 91 and 92 (1=Enabled, 0=Disabled).
91
2
50
Induce an automatic report
This parameter is used to induce an automatic report when the change of the current power is more/less than the threshold in wattage.
92
1
10
Induce an automatic report
This parameter is used to induce an automatic report when the change of the current power is more/less than the threshold in percentage.
Basic
COMMAND_CLASS_BASIC
Hail
COMMAND_CLASS_HAIL
Scene Activation
COMMAND_CLASS_SCENE_ACTIVATION
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Inclusion
Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Action button that you can find on the product's housing.
Exclusion
Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Action button that you can find on the product's housing.
Learn Mode (adding another controller)
N/A
Factory Reset
Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable.
Device Wake-Up
N/A
Additional Special Features
Support ""Over the Air Firmware Updating"" and “Z-Wave Security”.

 

Reviews

Write a review

Smart Switch Aeotec Heavy Duty Smart Switch for high load with consumption measurement Z-Wave Plus (GEN5)

Smart Switch Aeotec Heavy Duty Smart Switch for high load with consumption measurement Z-Wave Plus (GEN5)

Smart switch Aeotec Heavy Duty Smart Switch Z-Wave Plus (GEN5) by AEON LABS for large loads and high power (heavy duty)

30 other products in the same category:

Customers who bought this product also bought: