Viewed products





Confianza Online


Qubino Flush 1 Relay

ZMNHAD1

New

1 relay micromodule with Qubino Flush 1 Relay consumption control for on / off, with Z-Wave Plus technology. It is a relay used to turn on / off (On / Off - all / nothing) electrical devices such as lights, fans, ovens, washing machines, irons, power outlets, garage doors, electric radiators, water heaters, etc. ..

More details

In Stock

59,85 €

Technical characteristics

Technology Z-Wave Plus
Characteristic Consumption Measurement

More info

The smallest Z-Wave relay in the world

The Qubino Flush 1 Relay is ideal as an electric switch for lights, fans, ovens, washing machines, irons, sockets, garage doors, electric radiators, water heaters, etc. You can control it remotely through the Z-Wave network or through wall switches. It also measures the power consumption and supports the connection of a digital temperature sensor.

The smallest Z-Wave relay

The Z-Wave relay Qubino Flush 1 Relay is a micromodule that occupies less space than any other module with which it is compared to any other competitor and will fit easily into any conventional mechanism box.

Qubino Flush 1 Relay

This Z-Wave micromodule Qubino Flush 1 Relay is a relay used to turn on / off (On / Off - all / nothing) electrical devices such as lights, fans, ovens, washing machines, irons, power outlets, garage doors, electric radiators , water heaters, etc ...

This hidden relay micromodule, Qubino Flush 1 Relay has an input to connect a temperature probe , which suits it to control heating or air conditioning systems.

What can be used for?

The Qubino Flush 1 Relay is ideal for remote control and change of electrical devices (eg lights or fans).

Energy control

The simple relay Z-Wave Qubino Flush 1 Relay , makes measurement of electrical consumption of the connected electrical device and of itself, when it is in "standby" it only consumes 0.4 W.

Very versatile

The Qubino Flush 1 Relay , can operate through an extensive range of temperatures from cold -10ÚC to suffocating 40ÚC (14Ú 104ÚF). It supports the connection of a digital temperature sensor, which is also useful for creating complex scenarios. Each module also acts as a repeater in order to improve the range and stability of the Z-Wave network.

The simplest installation.

The extremely small size and a specially designed housing mean that the connection of the module inside a recessed mounting box is simple. The installation process, tested and approved by professional electricians , consists of only three simple steps:

1 - Remove the switches from the box and disconnect the cables.
2 - Connect the cables to the Qubino module and insert them into the box.
3 - Fix the switches to the box.

The most proven and reliable Z-Wave modules

Qubino's Z-Wave modules are install-and-forget products. The Qubino products that we offer, are manufactured to last, so they only use electronic components that meet the most demanding levels of quality. Our modules are also the most tested Z-Wave micromodules on the market. The Slovenian Institute of Quality and Measurement (SIQ), an independent European entity, checks the quality of the actual parameters of our products, including temperature increases, manufacturing, insulation resistance, electrical consumption and overloads according to European standards of the highest quality according to the specification of standard EN 60669-2-1.

Additional parameters for professionals.

The Qubino Flush 1 Relay micromodule   It has 15 additional parameters for its use by experts. Some of the most useful are

  • Adjustment of the mono-stable type (pulsator) or bi-stable
  • Activate or deactivate the ALL ON / ALL OFF functions
  • Automatic on / off output after set time

The micromodule can be controlled either through a Z-Wave network or through a wall switch. This module has been designed to be mounted inside a mechanism box and hidden behind a conventional wall switch.

We highlight as an advantage with respect to other regulators, that the Qubino Flush 1 Relay micromodule is able to control the electrical consumption of the connected load (lighting, fan ...). It also has a connector to which you can connect a temperature probe (optional, not included) to provide greater versatility to this module, which apart from the lighting control, offers control of electricity consumption and temperature information of the stay in the one that has been installed.

Electrical diagrams and technical specifications:

Electrical Schemes Qubino Flush 1 Relay

Electrical Schemes Qubino Flush 1 Relay

We emphasize that Qubino offers us strict quality, safety and durability standards in the manufacture of its hidden micromodules. It should be noted the selection of high quality components and high performance, such as the use of internal components of the Omron brand.

Feeding: 110 230 VAC ± 10%
50/60 Hz, (24 30 VDC)
Maximum AC output load (resistive load) * 1 X 10 A / 230 VAC
Maximum DC output load (resistive load) * 1 X 10 A / 30 VDC
Output circuit power of AC output (resistive load): 2300 W (230 VAC)
Output circuit power of DC output (resistive load): 240 W (24 VDC)
Accuracy of the power measurement: P = 5 50 W, +/- 3 W
P> 50 W, +/- 3%
Digital temperature sensor range: -50 ° ~ + 125 ° C, resolution 0.1 ° C
Cable length of the digital temperature sensor: 1000 mm
Operating Temperature: -10 ° ~ + 40 ° C
Distance up to 30 m indoors (depending on materials)
Dimensions (WxHxD) 41.8 x 36.8 x 15.4 mm
(packaging) (115 x 96 x 22)
Weight (including packaging) 48 g (64 g)
Electric consumption on standby 0.4 W
For installation in mechanism boxes Ø e 60 mm or 2 M
Switching by: Relay

* In the case of loads other than resistive loads, pay attention to the value of cosÆ and, if necessary, use a load lower than the nominal load. The maximum current for cosÆ = 0.4 is 3 A at 250 VAC, 3 A at 24 VDC L / R = 7 ms.

Meets CE and ROHS Certifications

Download

Extended Z-Wave info

Name: Flush 1 Relay
Manufacturer:QUBINO
Identifier:ZMNHAD1
Z-Wave Certification Number:ZC10-18015974
Hardware Plattform:ZM5202
FLiRS:NO
Role Type:Always On Slave
Short Description:The Qubino Flush 1 Relay is ideal for remotely controlling one light or electrical device (door lock, door opener, small appliances, etc.).
Description:The Flush 1 Relay controls on/off function for one electrical device. It measures power consumption of the connected device, and can be paired with a digital temperature sensor (sold separately). It supports push-button/momentary switches and toggle switches (default). The connection of a digital temperature sensor means you can create complex scenes and control any device relative to a set temperature range. The Qubino Flush 1 Relay also acts as a Z-Wave repeater to improve the range and stability of the Z-Wave network.

Manual download HERE.

Group
Max Nodes
Description
1
1
Lifeline group (reserved for communication with the primary gateway (hub)), 1 node allowed.
2
16
Basic on/off (status change report for Q⬆ load), up to 16 nodes.
3
16
Basic on/off (status change report for I2 input), up to 16 nodes.
4
16
Notification report (status change report for I2 input), up to 16 nodes.
5
16
Binary sensor report (status change of the I2 input), up to 16 nodes.
6
16
Basic on/off (status change report for I3 input), up to 16 nodes.
7
16
Notification report (status change report for I3 input), up to 16 nodes.
8
16
Binary sensor report (status change of the I3 input), up to 16 nodes.
9
16
Multilevel sensor report (triggered at change of temperature sensor) up to 16 nodes.
Number
Size (Bytes)
Default Value
Name
Description
1
1
1
In-wall Switch Type for Load 1 (Q⬆) to control I1
With this parameter, you can select between push-button (momentary) and on/off toggle switch types.
10
2
255
Activate / deactivate ALL ON / ALL OFF Functionality
Flush 1 Relay device responds to commands ALL ON / ALL OFF that may be sent by the primary or secondary gateway (hub) within the Z-Wave network.
100
1
0
– Enable / Disable Endpoint I2 or select the Notification Type and the Notification Event
Choose whether the Endpoint I2 is disabled (and not shown on the UI) or enabled (and displayed on the UI). By enabling this endpoint (setting it to be either a notification sensor or a binary sensor), the user also selects a Notification Type and a Notification Event for which notification reports will be sent (in case the endpoint is configured as a notification sensor). Endpoint device type selection: -notification sensor (1 - 6): GENERIC_TYPE_SENSOR_NOTIFICATION, SPECIFIC_TYPE_NOTIFICATION_SENSOR -sensor binary (9): GENERIC_TYPE_SENSOR_BINARY, SPECIFIC_TYPE_NOT_USED Values (size is 1 byte dec): • 9 - Sensor binary NOTE 1: After changing the values of the parameter, first exclude the device (without setting the parameters to their default values), then wait at least 30 seconds to re-include the device! NOTE 2: When the parameter is set to value 9 the notifications are sent for the Home Security notification type.
101
1
0
Enable / Disable Endpoint I3 or select the Notification Type and the Notification Event
Choose whether the Endpoint I3 is disabled (and not shown on the UI) or enabled (and displayed on the UI). By enabling this endpoint (setting it to be either a notification sensor or a binary sensor), the user also selects a Notification Type and a Notification Event for which notification reports will be sent (in case the endpoint is configured as a notification sensor). Endpoint device type selection: -notification sensor (1 - 6): GENERIC_TYPE_SENSOR_NOTIFICATION, SPECIFIC_TYPE_NOTIFICATION_SENSOR -sensor binary (9): GENERIC_TYPE_SENSOR_BINARY, SPECIFIC_TYPE_NOT_USED Values (size is 1 byte dec): • 9 - Sensor binary NOTE 1: After changing the values of the parameter, first exclude the device (without setting the parameters to their default values), wait at least 30 seconds and then re-include the device! NOTE 2: When the parameter is set to the value 9 the notifications are sent for the Home Security notification type.
11
2
0
Turn Load 1 (Q⬆) Off Automatically with Timer
If Load 1 (Q⬆) is ON, you can schedule it to turn OFF automatically after a period of time defined in this parameter. The timer is reset to zero each time the device receives an ON command, either remotely (from the gateway (hub) or associated device) or locally from the switch.
110
2
32536
Temperature Sensor Offset Settings
Set value is added to or subtracted from the actual measured value to adjust the temperature report sent by an external sensor (sold separately). This parameter only applies to Celsius temperature unit (the Fahrenheit unit is currently not supported).
12
1
0
Turn Load 1 (Q⬆) On Automatically with Timer
If Load (Q⬆) is OFF, you can schedule it to turn ON automatically after a period of time defined in this parameter. The timer is reset to zero each time the device receives an OFF command, either remotely (from the gateway (hub) or associated device) or locally from the switch.
120
1
5
Temperature Sensor Reporting Threshold If
If an external digital temperature sensor (sold separately) is connected to the device, it reports temperature readings based on the threshold defined in tIf an external digital temperature sensor (sold separately) is connected to the device, it reports temperature readings based on the threshold defined in this parameter. This parameter only applies to the Celsius temperature unit (the Fahrenheit unit is currently not supported).his parameter. This parameter only applies to the Celsius temperature unit (the Fahrenheit unit is currently not supported).
15
1
0
Set Timer Units to Seconds or Milliseconds
Choose if you want to set the timer in seconds or milliseconds in parameters 11 and 12. Please note that the value for this parameter applies to settings for Q⬆ load in all of the above parameters (timer on / timer off).
2
1
0
Input 2 contact type
This parameter defines input 2 contact type.
3
1
0
Input 3 contact type
This parameter defines input 3 contact type.
30
1
0
Restore on/off status for Q⬆ load after power failure
This parameter determines if on/off status is saved and restored for the load Q⬆ after power failure.
40
1
10
Watt Power Consumption Reporting Threshold for Q⬆ Load
Choose by how much power consumption needs to increase or decrease to be reported. Values correspond to percentages so if 10 is set (by default), the device will report any power consumption changes of 10% or more compared to the last reading. NOTE: Power consumption needs to increase or decrease by at least 1 Watt to be reported, REGARDLESS of percentage set in this parameter.
42
2
0
Watt Power Consumption Reporting Time Threshold for Q⬆ Load
Set value refers to the time interval with which power consumption in Watts is reported (0 – 32535 seconds). If 300 is entered (by default), energy consumption reports will be sent to the gateway (hub) every 300 seconds (or 5 minutes).
63
1
0
Choose Normally Closed or Normally Open for Q⬆ Load
Set value determines the type of the device connected to the Q⬆ output. The output type can be normally open (NO) or normally closed (NC).
Basic
COMMAND_CLASS_BASIC
Association Group Information V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V2
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V4
COMMAND_CLASS_METER_V4
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Notification V5
COMMAND_CLASS_NOTIFICATION_V5
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Sensor Binary
COMMAND_CLASS_SENSOR_BINARY
Sensor Multilevel V7
COMMAND_CLASS_SENSOR_MULTILEVEL_V7
Switch All
COMMAND_CLASS_SWITCH_ALL
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Inclusion
AUTOMATICALLY ADDING THE DEVICE TO A Z-WAVE NETWORK (AUTO INCLUSION)



1. Enable add/remove mode on your Z-Wave gateway (hub)

2. Connect the device to the power supply (with the temperature sensor already connected – sold separately*).

3. Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the device will automatically enrol in your network



MANUALLY ADDING THE DEVICE TO A Z-WAVE NETWORK (MANUAL INCLUSION)



1. Enable add/remove mode on your Z-Wave gateway (hub)

2. Connect the device to the power supply (with the temperature sensor already connected*)

3. Toggle the switch connected to the I1 terminal 3 times within 5 seconds

OR

If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds

4. A new multi-channel device will appear on your dashboard

*If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor.





*Make sure the device is excluded from your network before connecting the temperature sensor. Switch off the power supply, connect the temperature sensor, and re-include the device to your network.

Exclusion
REMOVAL FROM A ZWAVE NETWORK (Z-WAVE EXCLUSION)



1. Connect the device to the power supply

2. Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion

3. Enable add/remove mode on your Z-Wave gateway (hub)

4. Toggle the switch connected to the I1 terminal 3 times within 5 seconds

OR

If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds

5. The device will be removed from your network but any custom configuration parameters will not be erased

Factory Reset
FACTORY RESET



1. Connect the device to the power supply

2. Within the first minute (60 seconds) the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (5 times change switch state)

OR

If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds



*By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted. Use this reset procedure only when the main gateway (hub) is missing or otherwise inoperable.

Neutral Wire Required
For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.
Color
If the product is only available in one color, pick the color from the list.
Supported Meter Type
Indicate which type of metering is supported by the device.
Sensors
Sensor types supported by the product.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).

 

Reviews

Write a review

Qubino Flush 1 Relay

Qubino Flush 1 Relay

1 relay micromodule with Qubino Flush 1 Relay consumption control for on / off, with Z-Wave Plus technology. It is a relay used to turn on / off (On / Off - all / nothing) electrical devices such as lights, fans, ovens, washing machines, irons, power outlets, garage doors, electric radiators, water heaters, etc. ..

Accessories

30 other products in the same category:

Customers who bought this product also bought: