Viewed products





Confianza Online


Reduced price! ZIPATO sensor Puerta/Ventana  Z-Wave+ View larger

ZIPATO Sensor Door / Window Z-Wave+

ZIP-DS01Z

New

This detector sends a Z-Wave + radio signal when opening a door or window.

More details

In Stock

29,00 €

-10,00 €

39,00 €

Technical characteristics

Technology Z-Wave Plus

More info

This battery-powered detector allows you to send a Z-Wave + radio signal when you open a door or window. It consists of a piece with a magnet (the mobile part), fixed in the door or window, as well as the main unit placed in the fixed part of the window / door with screws or an adhesive. When the two parties are no longer in front, a message is sent automatically.

You need a Z-Wave controller (remote control, dongle, home automation controller, ...) to integrate this detector into your network if you already have an existing network.

FUNCTIONS:

Opening detector
Button to include / exclude the detector
Low battery detection
Supports 4 groups of associations (5 devices max / group)
Ease of use and installation

TECHNICAL CHARACTERISTICS :

Type of device Z-Wave +: slave
Power supply: 1 3V CR2 battery
Frequency: 868.42 MHz
Transmission distance: 30 m
Led screen
Operating temperature: 0 ° C to 60 ° C
Dimensions: 70 x 20 x 20 mm
Z-Wave + 500 series chipset

Extended Z-Wave info

Name: Door sensor
Manufacturer:Zipato
Identifier:ne-nas-ds01z.eu
Z-Wave Certification Number:ZC10-18015914
Hardware Plattform:ZM5202
FLiRS:NO
Role Type:Reporting Sleeping Slave
Short Description:Door/Window sensor that can be mounted to any door window or other opening object.
Description:Door/Window sensor that can be mounted to any door window or other opening object.

Manual download HERE.

Group
Max Nodes
Description
1
5
GROUP 1 is lifeline service that assigned to Sensor (Door/Window detector) status – Open/Close. It enables the sensor to send reports and readings to Z-Wave Controller or Z-Wave Gateway whenever the sensor is triggered. This Group Support: NOTIFICATION_REPORT BATTERY_REPORT SENSOR_BINARY_REPORT DEVICE_RESET_LOCALLY_NOTIFICATION
2
5
GROUP 2 allows for sending control commands to associated devices such as relay module, lighting, etc. This association group is configured through the advanced parameters no. 1 and 2. This Group Support: BASIC_SET.
3
5
GROUP 3 allows for Send Notification to associated devices in this group. This Group Support: NOTIFICATION_REPORT
4
5
GROUP 4 allows for Send Notification to associated devices in this group. This Group Support: SENSOR_BINARY_REPORT
Number
Size (Bytes)
Default Value
Name
Description
1
2
0
OFF Delay
This configuration parameter can be used to adjust the amount of delay before the OFF com mand is transmitted. This parameter can be configured with the value of 0 through 65535, where 0 means send OFF command immediately and 65535 means 65535 seconds of delay.
2
1
255
BASIC_SET level
Basic Set Command will be sent where contains a value when the door/window is opened or closed, Z-Wave controller or Z-Wave gateway will take it for consideration; for instance, if a lamp module receives the Basic Set Command of which value is decisive asto howbright of dim levelof lamp moduleshall be.
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Battery
COMMAND_CLASS_BATTERY
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Manufacturer Specific
COMMAND_CLASS_MANUFACTURER_SPECIFIC
Notification V4
COMMAND_CLASS_NOTIFICATION_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Sensor Binary V2
COMMAND_CLASS_SENSOR_BINARY_V2
Version V2
COMMAND_CLASS_VERSION_V2
Wake Up V2
COMMAND_CLASS_WAKE_UP_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Device Wake-Up
You can press the button once to wake up the device and send wakeup notification to controller. If press successfully, the LED will blink one time.
Inclusion
Add the Sensor (Door/Window detector) to Z-Wave Network



1.Remove the sensor cover.



2.Make sure the sensor is powered.



3.Set Z-Wave controller or Z-Wave gateway into inclusion mode (Refer to the controller or gateway operating manual)

4.Press the button three times within 1.5 second, the device will enter inclusion mode. And the LED will flash on and off alternately five times.
Exclusion
Delete the Sensor (Door/Window detector) from Z-Wave Network



1.Remove the device cover.



2.Make sure the sensor is powered.



3.Set Z-Wave controller or Z-Wave gateway into exclusion mode (Refer to the controller or gateway operating manual)

4.Press the button three times within 1.5 second, the device will enter exclusion mode.
Factory Reset
Note: to use the reset procedure only when the primary controller is missing or inoperable.



Restore the Sensor (Door/Window detector) to Factory Default Settings



Reset procedure will delete all information on the Z-Wave network and Z-Wave controller or Z-Wave Gateway, and restore the sensor to factory default settings.

1.Remove the device cover.



2.Make sure the sensor is powered.



3.Press and hold the button for 10 seconds,



4.Release the button.
Battery Quantity
Enter the number of batteries of the designated type that the product uses.
Battery Type
Enter the type (e.g. AA, CR2032, AAA) of the battery/batteries that the product uses.
Color
If the product is only available in one color, pick the color from the list.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).

 

Reviews

Write a review

ZIPATO Sensor Door / Window Z-Wave+

ZIPATO Sensor Door / Window Z-Wave+

This detector sends a Z-Wave + radio signal when opening a door or window.

9 other products in the same category:

Customers who bought this product also bought: