Viewed products





Confianza Online


Door or window sensor for embedding Aeotec GEN5 Z-Wave PLUS

AEO_ZW089

New

Detector of opening for installation embedded or emutida in door, offering improvements before the sabotage, with detection of opening or closing of doors, windows or furniture of instantaneous form

More details

Out of stock

63,50 €

Technical characteristics

Technology Z-Wave Plus

More info

The flush-mounted door sensor is a small and compact Z-Wave Plus sensor that communicates to the Z-Wave network whether a door is closed or open. It is almost invisible because it is designed to be embedded in a hole made for this purpose with a drill bit, usually at the top, on the top edge of a door or window. It is not too difficult to embed as the hole is usually unattainable in view when placed on the top of any wooden door. The installation in the domotics of the built-in sensor is easy since you only have to add the sensor to your Z-Wave network activating the battery and associating it with your system or Z-Wave home automation controller. When activated for security features, it allows accepting and sending security commands to other devices.

You can see the "unboxing" of the Aeotec door opening or window opening sensor here:

Characteristics:

Module type: Z-Wave Plus Transmitter - 868.42 MHz

Power supply: 1 CR2 battery (3V, 800 mAh)

Battery life: 1 year

Transmission distance: 30 meters

Dimensions: Fixed part: 62 x 18 mm (W x D) - Moving part: 13 x 18 mm (W x D)

Operating temperature: -10 ° C to 60 ° C

Relative humidity: from 8% to 80%

Extended Z-Wave info

Name: Recessed Door Sensor Gen5
Manufacturer:Aeotec
Identifier:ZW089-C
Z-Wave Certification Number:ZC10-14120011
Hardware Plattform:ZM5202
FLiRS:NO
Role Type:Reporting Sleeping Slave
Short Description:Aeon Labs Recessed Door Sensor Gen5 is a door sensor that can detect the state of the door's open/close.
Description:The Aeotec by Aeon Labs Recessed Door Sensor Gen5 is a door sensor that can detect the state of the door's open/close. It will report the door state to your controller/ gateway/associated nodes in real time when the state of your door has a change. It’s a security Z-Wave device that supports security encryption. Also it supports the “Over the Air Firmware Updating” that allows you wirelessly update its firmware if needs. It can be included and operated in any Z-Wave network with other Z-Wave certified devices from manufacturers and/or other applications.

Manual download HERE.

Group
Max Nodes
Description
1
5
Group 1 is assigned to the Lifeline association group and every device has 5 nodes to associate. The Basic Set CC or Sensor Binary report CC will be sent to the associated nodes in Group 1.
Number
Size (Bytes)
Default Value
Name
Description
1
1
0
Which value of the Sensor Binary Report will be sent when the magnet switch to open/close.
This parameter is used to set the Sensor binary report value when the magnet switch to open/close.
101
1
0
Enable/disable the function of low battery checking
This parameter is used to configure to enable/disable the function of low battery checking.(00==Disable, 1==Enable).
111
4
86640
The interval time of low battery checking.
This parameter is used to configure the interval time of low battery checking. Note: 1. The minimum unit of interval time is 4 minutes(240). If the value is set to 1 minute, the interval time will be 4 minutes. The same is if the value is set to 7 minutes, the interval time will be 8 minutes. 2. The possible values are unsigned value, so its range is 0 to 2147483647.
121
4
256
To set which command will be sent to the associated nodes when the magnet switch is triggered.
This parameter is used to set which command will be sent to the associated nodes when the magnet switch is triggered.
252
1
0
Enable/disable all configuration parameters to be locked
This parameter is used to enable/disable all configuration parameters to be locked. (0 =disable, 1 = enable)
254
2
0
Device Tag
This parameter is used to set the device tag. Note: The possible values are unsigned value, its range is 0 to 65535.
3
1
0
Which value of the Basic Set will be sent when the magnet switch to open/close.
This parameter is used to set the Basic Set value when the magnet switch to open/close.
Basic
COMMAND_CLASS_BASIC
Exclusion
Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Z-Wave button that you can find in back of the product.
Inclusion
Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Z-Wave button that you can find in the back of the product.
Device Wake-Up
Press and hold the Z-Wave button for 5 seconds will trigger sending the Wake up notification command and then keep waking up for 10 seconds after release the Z-Wave button.
Learn Mode (adding another controller)
N/A
Factory Reset
Press and hold the Z-Wave button that you can find in back of the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable.
Additional Special Features
Support ""Over the Air Firmware Updating"" and “Z-Wave Security”.

 

Reviews

Write a review

Door or window sensor for embedding Aeotec GEN5 Z-Wave PLUS

Door or window sensor for embedding Aeotec GEN5 Z-Wave PLUS

Detector of opening for installation embedded or emutida in door, offering improvements before the sabotage, with detection of opening or closing of doors, windows or furniture of instantaneous form

10 other products in the same category:

Customers who bought this product also bought: