No products
Prices are tax included
Product successfully added to your shopping cart
There are 0 items in your cart. There is 1 item in your cart.
View larger
Everspring 20W outdoor led spotlight with Z-Wave motion detector
EVR_EH403-3
New
This slim design projector with Z-Wave PIR detector is a compact fully automatic security projector.
Out of stock
- Remove this product from my favorite's list.
- Add this product to my list of favorites.
Technical characteristics
| Technology | Z-Wave Plus |
More info
Small but powerful, this slim projector with PIR detector is a compact, fully automatic security projector. Its aesthetic design makes it suitable for installation in the front areas of the house that are usually occupied by conventional lights and lamps.
When connected to the Z-Wave controller, the user can remotely turn the projector or LED spotlight on and off and be notified when the PIR detector detects motion.
This product supports the S2 security protocol, which uses encrypted Z-Wave Plus messages to communicate with other secure Z-Wave Plus products. A Z-Wave Plus secure controller must be used to fully utilize the safety features of this product.
Let's say that it can be considered a Z-Wave Plus sensor + actuator to be turned on by Z-Wave home automation and used as an external presence sensor, powered, without batteries and that
FUNCTIONS:
LED floodlight with Z-Wave motion detector
Two-way wireless communication
Integrates the S2 security protocol
Autoinclusion with the Z-Wave Controller
IP44 protection for outdoor use
Adjustable timer and brightness threshold
Rotating lens angle
Test mode for easy outdoor installation
TECHNICAL SPECIFICATIONS
Power supply: 100V - 240VAC, 50 / 60Hz
Power Consumption: 20W
Luminous flux: 1500 lm
Color temperature: 5000K, cool white
CRI: g70
Illumination angle:> 90 °.
Frequency: 868.42 Mhz
Range: up to 100m in open field
PIR coverage angle: 110 ° at 8m, height 2.4m
Sensor angle adjustment:
Horizontal: 60 °.
Up to 30 ° left
Up to 30 ° to the right
Brightness regulation: 30 - 200 lux
Timer setting: 8 ± 5 seconds - 12 ± 4 minutes
Weight: 830g
Dimensions: 201 x 196 x 88.8 mm
Operating temperature: -10 ~ 45 ° C
Humidity: 95% RH max.
Electrical classification: CLASS II
Extended Z-Wave info
Manual download HERE.
2. Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode.
2. Within 1 second of step 1, press the tamper switch again and hold until LED is off (about 5 seconds).
3. Node ID is excluded. The device reverts to factory default state and will be in auto-inclusion mode for 4 minutes.
4. Please use this procedure only when the network primary controller is missing or otherwise inoperable
The unit supports Auto Inclusion feature where it will automatically enter Inclusion mode when first powered up after a factory reset.
1. Prepare the Z-Wave controller.
2. Plug the cable plug to the wall socket to power up the unit.
3. The Link LED will start to blink slowly with 2-second on, 2-second off (for 2 minutes) which shows the unit does not be paired.
4. Within 30 seconds, put the Z-Wave Controller into inclusion mode.
5. The Inclusion process should be completed when the Link LED stops blinking.
Note: If you are connecting this unit to a Z-Wave Controller that utilizes the S2 security protocol, you may be asked by your controller to enter a 5-digit Device Specific Key (DSK) that is unique to each unit. This can be found in one of two places:
- on the QR code label on the back of the unit
- on the insert card inside the packaging.
6. Turn on the floodlight using the controller to check if the auto inclusion is working properly.
Manual Inclusion
1. Prepare the Z-Wave controller.
2. Press the tamper switch 3 times within 1.5 seconds to put the unit into inclusion mode.
