Viewed products





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

HANK LED Bulb RGB technology Z-Wave Plus

HNKERGB01

New

The Z-Wave LED bulb RGB for conventional socket E27 (the "fat" cap) of all life.

More details

Out of stock

35,70 €

-15%

42,00 €

Technical characteristics

Technology Z-Wave Plus

More info

Bring color to your life and create a personal comfortable atmosphere with white and colored dimmable tones. The Hank RGB LED bulb fits into each E27 bulb holder and can be connected to a smart home center through Z-Wave wireless technology just after screwing. The required radio chip is already integrated into the bulb housing. Through the remote control, smartphone or tablet you can vary the brightness and the color of the light as well. Daylight, candlelight or party mood: From now on, you can define a light atmosphere according to your wishes or use scenes (for example, in case of an alarm) activating the appropriate light color.

As a special function, the color of the Hank bulb light can be adjusted completely without using a smartphone application. Only control it by the existing wall switch. Through the combination of ON / OFF on the wall switch, the bulb will enter a fade mode and is dimmed through all the main colors. Once you have found the color you like, select it by turning the bulb on / off again. Then the fade mode will stop and the bulb will remain in the current color mode.

Due to LED technology, the power consumption is very low compared to conventional bulbs. Hank's bulb is as bright as a conventional 60W bulb, but it only needs 7W.

characteristics:

Lamp for cap type E27
Integrated radio chip
Colors: 3-channel RGB, 16 million colors, warm and cool white
Power consumption: max. 7 W
Intensity of light: 600 lm
Energy efficiency class: A +
Wireless technology: Z-Wave Plus
Dimensions: 115x65x65 mm

Extended Z-Wave info

Name: RGB Bulb
Manufacturer:Hank
Identifier:HKZW-RGB01
Z-Wave Certification Number:ZC10-16095231
Hardware Plattform:ZM5101
FLiRS:NO
Role Type:Always On Slave
Short Description:RGB Bulb is a smart bulb enables Z-Wave remote command and control (on/off/dim). It has over 16,000,000 colors, you can choose its color according to your favour.
Description:RGB Bulb is a smart bulb enables Z-Wave remote command and control (on/off/dim). It has over 16,000,000 colors, you can choose its color according to your favour.

Manual download HERE.

Group
Max Nodes
Description
1
5
Z-Wave Plus Lifeline RGB BULB supports only one association groupings: RGB BULB will send the follow notification to the associated nodes when the status of the RGB BULB is changed. 1. Set Configuration parameter 24 to 0: Reserved 2. Set Configuration parameter 24 to 1: Send Basic Report 3. Set Configuration parameter 24 to 2: Send Basic Report only when the status of the RGB BULB is not changed by Z-WAVE Command.
Number
Size (Bytes)
Default Value
Name
Description
21
1
0
Setting device status after power failure
Define how the RGB BULB will react after the power supply is back on.
24
1
1
Notification when Load status change
RGB BULB can send notifications to associated device (Group Lifeline) when the status of the RGB BULB is changed.
255
4
0
Reset to factory default
RGB BULB will exclude from the Z-Wave network with this particular command.
Exclusion
To remove the RGB BULB from the Z-Wave network:

(1) Screw in the RGB BULB.

(2) Set the Z-Wave network main controller into excluding mode

(see Z-Wave controller operating manual).

(3) Toggle the wall switch off and on 3 times quickly(within 3

and the final ending position of the wall switch must be on),

if the exclusion is successful, the RGB BULB will blink fast in

orange for less than 5 seconds and then keep on for 3 seconds.

RGB BULB will keep on warm white after the exclusion procedure

is finished.
Factory Reset
There are two ways to reset the RGB BULB. One is that removing

RGB BULB from the Z-Wave network, the other is that using the

configuration command class.
Inclusion
To include RGB BULB into a Z-Wave network as a non-security device:

(1) Make sure the power supply is disconnected and the RGB BULB is

located within a direct Z-Wave network's main controller

communication range.

(2) Set the Z-Wave network main controller into learning mode

(see Z-Wave network controller operating manual).

(3) Insert the RGB BULB into a lamp-socket and then power on.

(4) Auto-inclusion will be activated. If the inclusion is successful, the

RGB BULB will blink fast in blue for less than 5 seconds and then

keep on for 3 seconds. RGB BULB will keep on in the color before it

is included into the Z-Wave network after the inclusion procedure

is finished.



To include RGB BULB into a Z-Wave network as a security device:

(1) Screw in the RGB BULB.

(2) Set the Z-Wave network main controller into learning mode

(see Z-Wave network controller operating manual).

(3) Toggle the wall switch off and on 3 times quickly (within 3 seconds

and the final ending position of the wall switch must be on).

(4) If the inclusion is successful, the RGB BULB will blink fast in green

for less than 5 seconds and then keep on 3 seconds. RGB BULB will

keep on in the color before it is included into the Z-Wave network

after the inclusion procedure is finished.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.

 

Reviews

Grade 
07/13/2020

Bombilla económica

Económica y práctica. Muy útil para avisarte del disparo de una escena o para avisarte de si algo ocurre

Write your review!

Write a review

HANK LED Bulb RGB technology Z-Wave Plus

HANK LED Bulb RGB technology Z-Wave Plus

The Z-Wave LED bulb RGB for conventional socket E27 (the "fat" cap) of all life.

4 other products in the same category:

Customers who bought this product also bought: