Viewed products





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

Philio PAN08 Roller Shutter Controller - Z-Wave Blind Driver

PHI_PAN08

New

It allows the control of motors of blinds and awnings locally and remotely through the standard Z-Wave.

More details

Out of stock

47,20 €

-20%

59,00 €

Technical characteristics

Technology Z-Wave Plus

More info

Thanks to this module, you can control motorized roller shutters manually (by pushbutton) or through a remote control or Control Unit in your Z-Wave network. It has calibration technology, so that the PAN08 device can be used to control many types of blinds, awnings, etc.
Easy installation in a conventional mechanism box. It works like the rest of ZWave devices, such as a wireless repeater with other ZWave modules to offer total coverage of your home or office. (Meshed network).

Technical specifications:

  • Module type: receiver
  • Frequency radio: 868 MHz
  • Installation: in universal mechanism box. Three wire wiring. Requires neutral
  • Maximum load: up to 16A
  • Scope of the antenna: 30m in buildings
  • Power supply: AC 90V-240V
  • Dimensions: 47mmx39mmx15.6mm

Extended Z-Wave info

Name: Micro Module motor controller
Manufacturer:Zipato
Identifier:ph-pan08.eu
Z-Wave Certification Number:ZC10-17055604
Hardware Plattform:SD3502
FLiRS:NO
Role Type:Always On Slave
Short Description:Using Micromodule Motor Controller user can control connected roller shutters and blinds, finely adjust their position with his Z-Wave controller, Z-Wave remote or simple push of a button.
Description:Using Micromodule Motor Controller user can control connected roller shutters and blinds, finely adjust their position with his Z-Wave controller, Z-Wave remote or simple push of a button. Micromodule Motor Controller is Z-Wave Plus enabled device which makes it compatible with any Z-Wave enabled network, regardless of the manufacturer. Slim design makes it easy to fit in majority of wall boxes. New smart-relay calibration technology reduces inrush current caused by the load and enables module to work perfectly with all kinds of roller shutters and blinds. Micromodule is able to detect position of the Shutter by using the patterned power measuring method, so it can be remote controlled not only fully up or down, but also can be adjusted to ex. 30% or 50%. When manually operated by the push button, Micromodule Motor Controller can also memorize the position and send the new shutter position to its controller (ex. IP-Gateway).

Manual download HERE.

Group
Max Nodes
Description
1
1
Lifeline There is only one group called Group1, there is only one node for Group1 which support MULTILEVEL_SWITCH_REPORT, METER_REPORT_COMMAND_V3, ALARM_REPORT.
Number
Size (Bytes)
Default Value
Name
Description
1
2
720
Watt Meter Report Period
If the setting is configured for 1hour (set value =720), the Micromodule will report its instant power consumption every 1 hour to the node of corresponding Group. The maximum interval to report its instant power consumption is 45 hours (5s*32767/3600=45hr). Default value is 1 hour.
2
2
6
KWH Meter Report Period
If the setting is configured for 1hour (set value =6), the Micromodule will report its Accumulated Power Consumption (KW/h) every 1 hour to the node of corresponding Group. The maximum interval to report its Accumulated Power Consumption (KW/h) is 227.55 days (10min*32767/1440=227.55 days). Default value=1 hour.
3
2
500
Threshold of current for Load Caution
This is a warning when the wattage of load exceeds the preset threshold value, If the setting value is 500, when the load current over this value, Micromodule will send current meter report command to the node of corresponding Group. Default value=500.
4
2
10000
Threshold of KWH for Load Caution
This is a warning when the KWh of load over the preset threshold value, If the setting value is 10000, when the Accumulated Power Consumption of Relay1 or Relay2 over this value, Micromodule will send KWh Meter Report command to the node of corresponding Group, minimum value is 1KWh and default value is 10000 kWh.
5
1
1
External switch type
1.ONE PUSH BUTTON When the configuration setting is One Push Button, only S1 input will be valid. The control moving commands can be accepted in this switch type while the shutter is moving. In this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing S1 just like the operation of include button. When S1 is short pressed, the shutter will move up toward TOP(0xFF). If during this movement S1 is short pressed again, the shutter will stop moving. A third short pressing of S1 will move the shutter down toward BOTTOM(0x00). If during this movement S1 is short pressed again, the shutter will stop moving. And so on… Inverting direction and stopping. 2.TWO PUSH BUTTON: (THE DEFAULT SETTING IS TWO PUSH BUTTON (2)) If this setting is configured as Two Push Button, S1 and S2 input will be valid, but will not accept pressing S1 and S2 at the same time. In this switch type, the inclusion/exclusion/reset/association function can also be fulfilled by pressing S1 or S2 just like the operation of include button. When S1 is pressed and held more than 1.5 seconds, the shutter will move up toward TOP(0xFF), and the shutter will stop moving when S1 is released. When S2 is pressed and held for more than 1.5 seconds, the shutter will move down toward BOTTOM(0x00), and the shutter will stop moving when S2 is released.When S1 is short pressed, the shutter will move up toward TOP(0xFF). If during this movement S1 i short pressed again S1 again, the shutter just keep moving up toward TOP(0xFF). The easy way to stop this moving is short pressing S2. When S2 is short pressed, the shutter will move down toward BOTTON(0x00). If during this movement S2 is short pressed again S2 again, the shutter just keep moving down toward BOTTON(0x00). The easy way to stop this moving is short pressing S1. When in Two Push Button switch type, S1 or S2 are pressed and not released, and PAN08 receive any control moving command from Z-Wave RF (Ex. BASIC_SET, BINARY_SWITCH_SET, MULTILEVEL_SWITCH_SET, MULTILEVEL_SWITCH_START_LEVEL_CHANGE or MULTILEVEL_SWITCH_STOP_LEVEL_CHANGE or SCENE_ACTIVATION_SET), PAN08 won’t do any change in position but report alarm to Group1 (Alarm_Type=1, Alarm_level =0xFF), this indicate that the S1 or S2 not been release.
6
1
2
Level report mode
Mode 1 : In 5 seconds period after controlled by a moving command, it will report the destination level when received request command. Out of the 5 seconds period, it will report the actual level of the shutter when received request command. Mode 2 : Whenever the shutter moves past a 10 percent level, it will auto report the level to Group 1 node.
Alarm
COMMAND_CLASS_ALARM
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic
COMMAND_CLASS_BASIC
Configuration
COMMAND_CLASS_CONFIGURATION
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V2
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Meter V3
COMMAND_CLASS_METER_V3
Powerlevel
COMMAND_CLASS_POWERLEVEL
Scene Activation
COMMAND_CLASS_SCENE_ACTIVATION
Scene Actuator Conf
COMMAND_CLASS_SCENE_ACTUATOR_CONF
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Switch Multilevel V3
COMMAND_CLASS_SWITCH_MULTILEVEL_V3
Version V2
COMMAND_CLASS_VERSION_V2
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Factory Reset
Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.

Pressing Include button three times within 2 seconds will enter inclusion mode.

Within 1 second, press Include button again for 5 seconds until LED is off.

IDs are excluded.
Inclusion
Put your Z-Wave controller into inclusion mode by following the instructions provided by the controller manufacturer.

Pressing Include button three times within 2 seconds will enter inclusion mode.
Exclusion
Put the Z-Wave Controller in exclusion mode.

Pressing Include button three times within 2 seconds will enter exclusion mode.

Node ID has been excluded.

Electric Load Type
Select the electric load type(s) supported by the device.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Switch Load Capacity Watts
The amount of switch load energy the product is rated for in Watts
Loads Controlled
The number of different loads controllable by the product if it supports more than one.
Supported Meter Type
Indicate which type of metering is supported by the device.
Switch Type
Describes the type of operator for a switch.
Window Covering Control Features
Select the feature(s) supported in the Window Covering Control product.
Color
If the product is only available in one color, pick the color from the list.
Neutral Wire Required
For electric in-wall/wired switches, indicate whether a neutral wire is required for installation.

 

Reviews

Write a review

Philio PAN08 Roller Shutter Controller - Z-Wave Blind Driver

Philio PAN08 Roller Shutter Controller - Z-Wave Blind Driver

It allows the control of motors of blinds and awnings locally and remotely through the standard Z-Wave.

6 other products in the same category:

Customers who bought this product also bought: