Viewed products





Confianza Online


domoticalia.es/es/ Reviews with ekomi.es

Heatit Z-WATER Z-Wave + DIN rail control module for hydraulic heating 10 outputs

HEATIT-4512475

New

Module for installation on DIN rail, Z-Wave + technology for the control of hydraulic heating up to 10 outputs. Heatit Z-Water is a DIN rail mounted controller for controlling hydronic heating.

More details

This product is no longer in stock

326,70 €

Technical characteristics

Technology Z-Wave Plus

More info

Heatit Z-Water is a DIN rail mounted controller for controlling hydronic heating. The module clips directly to a DIN rail to add a variety of functions to your Z-Wave wireless network. Heatit Z-Water is equipped with 10 relay outputs and has 4 analog inputs. The module is powered by a 230V AC mains connection and is capable of providing a 24V DC or 230V output power.

The relay outputs of the Heatit Z-Water can be freely controlled from the Z-Wave network and can be used for various purposes, for example control of on / off lights, control of valve actuators in a underfloor heating system or control of other home automation systems.

The Heatit Z-Water inputs are analog inputs for interfacing simple temperature sensors; NTC, PT1000, etc.

The level and status light indication on the front of the Heatit Z-Water controller is configurable.

Introduction video to Heatit Z-Water DIN Rail Regulator to control water heating systems:

Short video clip showing how to configure Heatit Z-Water control by using Heatit Z-TRM2 using Fibaro Home Center.

Connection diagrams:

Heatit Z-Water Connections

FUNCTIONS:


Controller for water heating systems
Relay outputs can control the actuators of a water-based underfloor heating system
Can be used to control 24V or 230V actuators
4 analog inputs supporting temperature sensors
Can be used with a Heatit Z-Temp2 sensor in each zone
DIN rail mounting
Works as a Z-Wave repeater to improve the range of the Z-Wave network
Firmware updates (OTA)
Supports encryption mode: S0, S2 Authenticated Class, S2 Unauthenticated Class

TECHNICAL SPECIFICATIONS:

Protocol: Z-Wave Plus, 868.4 MHz
Chip: Z-Wave 500 chip
Nominal voltage: 100V - 240V 50 / 60Hz
Power Consumption: 0.6W Standby
Ambient temperature: 0 ° C to 40 ° C
Humidity: Maximum 90% RH
Fuse: 3.15A fast acting, UMF 250 Schurter Inc Part Number: 3405.0171.11
24VDC output: 1.17 A, 28 W maximum
Maximum switching current: 5A
Maximum load per relay: 150 W
Maximum voltage: 250 V AC, 30 V DC
Tickets:
Maximum input voltage: 10V DC
Input impedance: 10K ©
Loop output voltage: 5V DC
Dimensions: 160 x 86 x 58 mm

Extended Z-Wave info

Name: Heatit Z-Water
Manufacturer:HEATIT
Identifier:Z-Water
Z-Wave Certification Number:ZC10-19036400
Hardware Plattform:ZM5101
FLiRS:NO
Role Type:Always On Slave
Short Description:Heatit Z-Water is a DIN-rail regulator for controlling hydronic heating. Heatit Z-Water is a module that clips right onto a DIN rail to add a variety of functions to your wireless Z-Wave network.
Description:Heatit Z-Water is equipped with 10 relay outputs and 4 analog inputs, and a Z-Wave radio for interfacing to the wireless Z-Wave network. The regulator can be power supplied from a 230V AC mains connection, and is able to deliver an output supply of 24V DC. Heatit Z-Water relay outputs are able to be freely controlled from the Z-Wave network, and can be used for several purposes, e.g. on/off control of light, control of valve actuators for an underfloor heating system, or control of other home automation systems. Heatit Z-Water inputs are analog inputs for interfacing simple temperature sensors; NTC, PT1000, etc. It is possible to configure the level and the indication of the status indicator LED in the front of the Heatit Z-Water regulator.

Manual download HERE.

Group
Max Nodes
Description
1
5
Lifeline. - Reset notification - Basic Report On / Off - Multilevel Sensor Report
2
5
Sends Multilevel Sensor Reports for input 1.
3
5
Sends Multilevel Sensor Reports for input 2.
4
5
Sends Multilevel Sensor Reports for input 3.
5
5
Sends Multilevel Sensor Reports for input 4.
Number
Size (Bytes)
Default Value
Name
Description
1
1
1
Status LED
Configuration of the status LED.
10
1
0
Input 4 calibration.
Configures the functionality of input 4.
11
2
6
Input 1 report interval
Time interval between consecutive temperature reports. Temperature reports can be also sent as a result of polling.
12
2
6
Input 2 report interval
Time interval between consecutive temperature reports. Temperature reports can be also sent as a result of polling.
13
2
6
Input 3 report interval
Time interval between consecutive temperature reports. Temperature reports can be also sent as a result of polling.
14
2
6
Input 4 report interval
Time interval between consecutive temperature reports. Temperature reports can be also sent as a result of polling.
2
1
50
Status LED brightness level
Configure the percentage of light in the status LED, when the LED is turned on.
3
1
1
Thermistor type connected to input 1
This parameter decides which kind of thermistor that is connected to the input.
4
1
1
Thermistor type connected to input 2
This parameter decides which kind of thermistor that is connected to the input.
5
1
1
Thermistor type connected to input 3.
This parameter decides which kind of thermistor that is connected to the input.
6
1
1
Thermistor type connected to input 4
This parameter decides which kind of thermistor that is connected to the input.
7
1
0
Input 1 calibration
Configures the functionality of input 1.
8
1
0
Input 2 calibration
Configures the functionality of input 2.
9
1
0
Input 3 calibration
Configures the functionality of input 3.
Association Group Info
COMMAND_CLASS_ASSOCIATION_GRP_INFO
Association V2
COMMAND_CLASS_ASSOCIATION_V2
Basic V2
COMMAND_CLASS_BASIC_V2
Battery
COMMAND_CLASS_BATTERY
Configuration V3
COMMAND_CLASS_CONFIGURATION_V3
Device Reset Locally
COMMAND_CLASS_DEVICE_RESET_LOCALLY
Firmware Update Meta-Data V4
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
Manufacturer Specific V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
Multi-Channel Association V3
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
Multi-Channel V4
COMMAND_CLASS_MULTI_CHANNEL_V4
Powerlevel
COMMAND_CLASS_POWERLEVEL
Security S0
COMMAND_CLASS_SECURITY
Security S2
COMMAND_CLASS_SECURITY_2
Sensor Multilevel V5
COMMAND_CLASS_SENSOR_MULTILEVEL_V5
Supervision
COMMAND_CLASS_SUPERVISION
Switch Binary
COMMAND_CLASS_SWITCH_BINARY
Transport Service V2
COMMAND_CLASS_TRANSPORT_SERVICE_V2
Version V3
COMMAND_CLASS_VERSION_V3
Z-Wave Plus Info V2
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
Factory Reset
Heatit Z-Water can be factory reset by pressing the small button through the little hole, marked with the text “INCLUSION”,

in front of the Heatit Z-Water regulator for at least 10 seconds.



NOTE: Only use this procedure when the primary network controller is missing or is otherwise inoperable.
Inclusion
Add

Please refer to your primary controller manual on how to enter

add mode. The device can only be added from the network if the primary controller is in add mode.



When the primary controller is set to add modus press

the ”INCLUSION” button once on the device.

Exclusion
Remove

Please refer to your primary controller manual on how to enter

remove mode. The device can only be removed from the network if the primary controller is in remove mode.



When the primary controller is set to remove modus press

the ”INCLUSION” button once on the device.
Switch Load Capacity Watts
The amount of switch load energy the product is rated for in Watts
Switch Load Capacity Current
The amount of switch load energy the product is rated for in Amps
Switch Load Capacity Volt-Ampere
The amount of switch load energy the product is rated for in VA (Volt-Amperes)
Loads Controlled
The number of different loads controllable by the product if it supports more than one.
Firmware Updatable
Indicates whether the firmware can be updated and whether it is done by the consumer or a technician.
Supported Notification Types
Select the Notification Types that the product handles (controllers), or sends (slaves).
Electric Load Type
Select the electric load type(s) supported by the device.
Sensors
Sensor types supported by the product.

 

Reviews

Write a review

Heatit Z-WATER Z-Wave + DIN rail control module for hydraulic heating 10 outputs

Heatit Z-WATER Z-Wave + DIN rail control module for hydraulic heating 10 outputs

Module for installation on DIN rail, Z-Wave + technology for the control of hydraulic heating up to 10 outputs. Heatit Z-Water is a DIN rail mounted controller for controlling hydronic heating.

12 other products in the same category:

Customers who bought this product also bought: